ISL83490IB - 3.3V 10Mbps RS-485/RS-422 Transceiver | Renesas
Référence : ISL83490IB ✗ Fin de vieISL83490IB Présentation
A differential transceiver is an interface IC that translates logic-level signals into balanced differential voltage pairs and converts received differential signals back into CMOS-compatible outputs. The RS-485 and RS-422 standards define the physical signaling method rather than the data protocol. This distinction allows ISL83490IB to carry data generated by UARTs, microcontrollers, industrial controllers, or other serial equipment while leaving packet framing and higher-layer control to the connected system.
The ISL83490IB provides one transmit driver and one receive channel, supports 3.3 V operation, and is specified for data rates up to 10 Mbps. Its full-duplex configuration permits simultaneous transmission and reception on separate differential pairs. This is advantageous for point-to-point links, industrial equipment connections, test systems, and embedded control networks where half-duplex bus arbitration would add unnecessary application complexity. The SOIC-8 package also keeps the interface compact while providing adequate pin spacing for conventional board assembly.
Renesas identifies the ISL83490 family as a low-power, high-speed RS-485/RS-422 transceiver family with operating variants described as high-speed or slew-rate-limited. The exact drive strength, receiver thresholds, bus loading, and propagation-delay limits should be taken from the pin-specific manufacturer datasheet before assigning a cable length or termination network. For long cables, incorrect termination, excessive stub lengths, or incompatible grounding can increase reflections even when the transceiver operates within its rated data rate.
Typical uses include industrial control links, factory equipment connections, building automation equipment, instrumentation, and embedded serial links. In these systems, the transceiver converts the controller's UART logic into a balanced differential signal and receives the remote signal with common-mode rejection. Board-level protection, isolation, surge handling, and ground strategy remain application-level concerns because the ISL83490IB is primarily a signal interface rather than a surge-protection device.
A robust layout should route the differential driver and receiver traces as a closely coupled pair with continuous reference planes, keep the driver output path short, and place any termination components near the appropriate connector or transceiver pin. Decoupling capacitors should connect directly to the device supply and ground pins with minimal loop area. Avoid adding large test pads or long stub branches to the bus traces, because such structures can degrade edge response at the supported 10 Mbps signaling rate.
This page combines lifecycle information, interface-family positioning, compatible ordering variants, package guidance, and application-oriented design considerations. It is intended to accelerate component selection and PCB planning while keeping the manufacturer datasheet authoritative for pin assignments, electrical limits, recommended operating conditions, and ordering information.
Alternatives de remplacement direct pour ISL83490IB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ISL83490IB (même facteur de forme et même empreinte) — différant par Maximum Data Rate, Package, Product Type, Supported Standards.
ISL83490IBZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83490IBZ-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83490IB-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83490IB Spécifications
| Product Type | RS-485/RS-422 differential transceiver |
| Tension d'alimentation | 3.3 V |
| Maximum Data Rate | 10 Mbps |
| Duplex Mode | Full duplex |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| Supported Standards | RS-422 and RS-485 |
| Boîtier | 8-pin SOIC, 3.90 mm width |
| Type de montage | Surface mount |
| Plage de température de fonctionnement | -40°C to +85°C |
| Statut du cycle de vie | Obsolete |
Guide de configuration des broches du ISL83490IB 8-pin soic, 3.90 mm width
Configuration des broches du ISL83490IB (boîtier 8-pin soic, 3.90 mm width). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ISL83490IB.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ISL83490IB convient pour 6 applications: Industrial Controller Field Bus, Building Automation Equipment, Test and Measurement Instrumentation, Embedded UART Communication, Robotics and Motor Control, Point-to-Point Data Links.
Industrial Controller Field Bus
The ISL83490IB fits full-duplex industrial links that carry controller data over balanced copper pairs. Its 3.3 V supply matches modern embedded logic, while the 10 Mbps rate provides ample bandwidth for command, status, and diagnostic traffic. The integrated transmitter and receiver create separate differential paths, avoiding half-duplex bus contention. Install termination at the physical bus endpoint and validate return loss over the intended cable length, since transceiver speed alone does not guarantee reliable communication in every topology.
Recommandé
Building Automation Equipment
The ISL83490IB can connect a low-voltage controller to field equipment over a full-duplex RS-485/RS-422 interface. The -40°C to +85°C rating supports equipment operating across industrial temperature ranges, and the 8-pin SOIC footprint simplifies compact controller-board designs. Use the device with isolated or non-isolated grounding appropriate to the building installation, and place protection elements at the cable entry so transient energy does not reach the transceiver pins.
Recommandé
Test and Measurement Instrumentation
For bench instruments and automated test equipment, the ISL83490IB provides a compact differential interface between a controller and remote fixtures. A 10 Mbps ceiling supports high-volume command exchange and status updates, while full-duplex operation permits simultaneous transmission and reception. Keep the high-speed differential route short and controlled, use a common reference plane, and verify the receiver behavior with the actual cable and connectors. Protection or isolation may be needed when fixtures are connected to external equipment.
Recommandé
Embedded UART Communication
The ISL83490IB extends a 3.3 V UART or microcontroller through balanced RS-485/RS-422 wiring. Differential signaling improves noise immunity over longer interconnects than a single-ended interface, particularly in equipment cabinets containing motors and switching power converters. The separate driver and receiver channels support dedicated transmit and receive pairs. Configure the logic-side enables according to the datasheet and keep supply-return paths close to each signal route to minimize common-mode conversion.
Recommandé
Robotics and Motor Control
The ISL83490IB is suitable for command and feedback links between a robot controller and distributed motor-control electronics. Full-duplex operation allows controller commands to travel while position, current, and diagnostic information returns on separate differential pairs. The 10 Mbps capability is well above the throughput normally required for motor commands, leaving margin for expansion. Keep the bus interface away from motor-current paths, use a suitable chassis or cable ground strategy, and add surge protection where robots connect to long external cables.
Recommandé
Point-to-Point Data Links
The ISL83490IB works well in short point-to-point links where both endpoints transmit and receive independently. Its 3.3 V operation, 10 Mbps capability, and 8-pin SOIC package simplify interfaces between instrument subsystems, peripheral controllers, and remote I/O modules. Unlike a multidrop bus, a point-to-point arrangement normally uses one termination at the receiving end of each differential pair. Validate the receiver threshold and common-mode range against the complete system before release, particularly when ground-potential differences are possible.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL83490IB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL83490IBZ | ISL83490IBZ-T | ISL83490IB-T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
| Transmitter and Receiver Count | 1 transmitter, 1 receiver | 1 transmitter, 1 receiver | 1 transmitter, 1 receiver | 1 transmitter, 1 receiver |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Principaux différenciateurs
- Direct 10 Mbps full-duplex interface (vs ISL83490IBZ)
- No PCB modification for the closest ordering replacement (vs ISL83490IBZ)
- Separate differential transmit and receive paths (vs ISL83490IB-T)
Notes de conception
Route each differential pair as a tightly coupled, impedance-controlled trace with a continuous reference plane beneath it. Keep the ISL83490IB output section short, avoid test pads and branch stubs on the bus, and place termination only at the defined physical endpoint of the line. At 10 Mbps, even short discontinuities can create reflections that reduce receiver margin.
Place the device supply bypass capacitor directly across the supply and ground pins, with a short, low-inductance connection. Keep the ground return under the SOIC footprint and separate logic-supply routing from motor, relay, and power-converter paths. If the interface uses isolated power, confirm that the isolated-side ground and transceiver ground arrangement satisfies the receiver common-mode limits in the manufacturer datasheet.
Do not substitute ISL83491IBZ or another family member solely because it also uses an 8-pin SOIC. Although the family offers related products, receiver enables, shutdown behavior, and other functions can differ. For an exact board-level replacement of the ISL83490IB, use ISL83490IBZ after confirming lifecycle and ordering requirements, and compare the complete pin-description and electrical-characteristic tables.
Use the shortest practical connection from the transceiver to the cable connector, and place common-mode chokes or protection devices where their capacitive loading will not impair the intended 10 Mbps edge rate. Connect cable shields according to the installation’s grounding strategy. Validate radiated and conducted emissions after installation because enclosure grounding, cable geometry, and connector transitions can dominate the transceiver’s board-level behavior.
Informations de conformité
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ISL83490IB ordering code. Confirm material and qualification status with Renesas before use in regulated or automotive designs.