KSZ8081MNXCA - 10/100 Ethernet PHY | Microchip | QFN-32
MPN: KSZ8081MNXCA ✓ Hoạt độngKSZ8081MNXCA Tóm tắt
An Ethernet PHY is an interface integrated circuit that converts digital MAC signals into electrical signaling suitable for copper cabling and converts received cable signals back into digital data. In the hierarchy, the KSZ8081 is an Ethernet physical-layer transceiver, an interface IC, a network-interface component, and a semiconductor. It sits between a network controller or embedded processor with an MII interface and a CAT-5 unshielded twisted-pair network connection.
The device supports both 10BASE-T and 100BASE-TX data rates on standard CAT-5 UTP cabling. Its Full MII connection provides parallel data and control signaling to the host Ethernet controller, while the integrated PHY reduces the number of external interface components required on a network port. The 32-QFN package includes an exposed pad for improved heat conduction and supports a compact 5 x 5 mm PCB footprint.
The KSZ8081 family is designed for space-constrained Ethernet equipment requiring a conventional copper twisted-pair port. The manufacturer describes the KSZ8081 as a highly integrated PHY that reduces board cost and space, making it appropriate for industrial controllers, embedded systems, access equipment, and compact network interfaces. A 25 MHz crystal can be used to generate the required clocks in applicable family configurations, including the 50 MHz RMII reference output identified for the KSZ8081RNB.
Typical implementations place the PHY close to the RJ45 connector and magnetic network interface, with short differential copper traces routed to maintain Ethernet signal quality. Decoupling should follow the manufacturer's recommended circuit, and the exposed pad requires a properly designed ground and thermal-via arrangement. Component values and layout must be checked against the current manufacturer datasheet before release to production.
The KSZ8081MNXCA is intended for designs using a 3.3 V Ethernet PHY with Full MII host signaling. Engineers should verify the exact MII clocking mode, magnetics selection, cable-length support, and diagnostic behavior against the device configuration required by the target system, particularly when using a different suffix or package option.
This product page combines the principal electrical, package, interface, application, and replacement information needed for initial design selection. It also distinguishes true package-compatible options from related KSZ8081 variants and highlights the checks that should be completed before any PHY replacement is approved for an existing PCB.
Bộ thay thế dễ dàng lắp đặt cho KSZ8081MNXCA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với KSZ8081MNXCA (cùng hình factor và footprint) — khác nhau ở Package.
KSZ8081MNXIA-TR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →KSZ8081RNBCA-TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8081RNDCA-TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8081MNXCA-TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
KSZ8081MNXCA Thông số kỹ thuật
| Product Type | 10BASE-T/100BASE-TX Ethernet physical-layer transceiver |
| Manufacturer | Microchip Technology |
| Supported Data Rates | 10 Mbit/s and 100 Mbit/s |
| PHY Channel Count | 1 channel |
| Host Interface | Full MII |
| Điện áp cung cấp | 3.3 V |
| Power Supply Architecture | Single supply |
| Cable Support | CAT-5 unshielded twisted pair |
| Ethernet Standard | IEEE 802.3 |
| Hộp | 32-pin QFN, 5 x 5 mm |
| Exposed Thermal Pad | Present |
| Lead Style | No lead |
| Nhiệt độ hoạt động | -40 C to +85 C |
| Temperature Grade | Commercial |
| Packaging | Tray |
| Crystal Reference Frequency | 25 MHz |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
Hướng dẫn cấu hình chân KSZ8081MNXCA 32-pin qfn, 5 x 5 mm
Cấu hình chân cho KSZ8081MNXCA (32-pin qfn, 5 x 5 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho KSZ8081MNXCA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
KSZ8081MNXCA phù hợp cho 6 Áp dụngs: Embedded Ethernet Control, Industrial Monitoring Equipment, Network Interface Adapter, Instrumentation and Test Equipment, Industrial IoT Gateway, Access and Control Terminals.
Embedded Ethernet Control
The KSZ8081MNXCA suits embedded controllers that require a compact 10/100 Mbit/s Ethernet port without implementing the physical layer in discrete components. Its single 3.3 V supply and Full MII interface provide a direct digital connection to an Ethernet MAC, while the PHY handles 10BASE-T and 100BASE-TX signaling over CAT-5 UTP. Placing the device near the magnetics and RJ45 connector can reduce board area and routing complexity. The design should follow the manufacturer typical-application circuit for decoupling, clocking, exposed-pad grounding, and magnetic-interface values.
Được đề xuất
Industrial Monitoring Equipment
The KSZ8081MNXCA is appropriate for industrial monitoring and control equipment requiring wired Ethernet connectivity in a commercial-grade temperature range of -40 C to +85 C. Its 32-QFN, 5 x 5 mm footprint preserves PCB area in compact instruments, and support for both 10 and 100 Mbit/s allows connection to common legacy and fast Ethernet infrastructure. Designers should verify the enclosure temperature rise, galvanic isolation strategy, magnetics, and grounding because the PHY itself does not provide an isolation barrier.
Được đề xuất
Network Interface Adapter
The KSZ8081MNXCA can form the physical-layer portion of a small network interface adapter that connects a host controller through Full MII to a standard copper Ethernet jack. Its integrated 10BASE-T/100BASE-TX PHY reduces the adapter's component count and footprint compared with a discrete transceiver arrangement. The implementation should preserve short differential routes between the PHY, isolation or filtering components, magnetics, and connector, while following the manufacturer layout for the exposed pad and power bypass network.
Được đề xuất
Instrumentation and Test Equipment
The KSZ8081MNXCA is well suited to data-acquisition and test equipment that must communicate with Ethernet management stations or factory test systems. The Full MII interface permits structured digital connection to a capable MAC or controller, while the PHY handles the physical copper link at 10 or 100 Mbit/s. Designers should use short, controlled-impedance routing and verify the clock configuration for deterministic data transfer. The exposed thermal pad should be tied to the recommended ground plane and furnished with thermal vias to avoid concentrating heat in the 5 x 5 mm package.
Được đề xuất
Industrial IoT Gateway
The KSZ8081MNXCA provides a compact wired-network endpoint for industrial IoT gateways that need reliable 10/100BASE-TX connectivity over CAT-5 UTP. Its small QFN footprint supports dense gateway assemblies, and its single 3.3 V supply simplifies power architecture when the surrounding controller also operates at compatible logic levels. The final design must account for the gateway enclosure's thermal environment, Ethernet isolation requirements, cable surge exposure, and production-test access to diagnostic functions described in the manufacturer documentation.
Được đề xuất
Access and Control Terminals
The KSZ8081MNXCA can support access terminals, controllers, and remote service equipment that connect to Ethernet-based management networks. Support for 10 Mbit/s remains useful when interoperating with older infrastructure, while 100 Mbit/s handles typical controller traffic. The PHY should be placed adjacent to the magnetic network interface, with the differential route kept short and symmetrical. Before production release, confirm the exact Full MII clocking arrangement, reset behavior, diagnostic pins, and exposed-pad connection against the current Microchip datasheet.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho KSZ8081MNXCA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | KSZ8081MNXIA-TR | KSZ8081RNBCA-TR | KSZ8081RNDCA-TR | KSZ8081MNXCA-TR |
|---|---|---|---|---|---|
| Package | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) | 32-QFN (5 x 5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Product Type | 10BASE-T/100BASE-TX physical-layer transceiver | 10BASE-T/100BASE-TX physical-layer transceiver | 10BASE-T/100BASE-TX physical-layer transceiver | 10BASE-T/100BASE-TX physical-layer transceiver | 10BASE-T/100BASE-TX physical-layer transceiver |
| Supported Data Rates | 10 Mbit/s and 100 Mbit/s | 10 Mbit/s and 100 Mbit/s | 10 Mbit/s and 100 Mbit/s | 10 Mbit/s and 100 Mbit/s | 10 Mbit/s and 100 Mbit/s |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Ethernet Compliance | IEEE 802.3 | IEEE 802.3 | IEEE 802.3 | IEEE 802.3 | IEEE 802.3 |
Bảo phân biệt quan trọng
- Direct Full MII integration (vsKSZ8081RNBCA-TR)
- Single 3.3 V supply architecture (vsKSZ8081MNXIA-TR)
- Compact 5 x 5 mm footprint (vsKSZ8081RNDCA-TR)
- Commercial temperature coverage (vsKSZ8081MNXCA-TR)
Ghi chú thiết kế
Place the KSZ8081MNXCA close to the Ethernet magnetics and RJ45 connector, and keep the 100BASE-TX differential routes short, symmetrical, and free of unnecessary vias. Follow the manufacturer reference layout for component spacing and controlled-impedance geometry. The exposed pad must use the datasheet-recommended ground connection and thermal-via pattern; a generic exposed-pad land pattern should not be substituted without checking the package drawing.
Use the manufacturer-recommended 3.3 V decoupling network and place the bypass capacitors directly beside the corresponding supply and ground pins. Keep the supply return path through the exposed pad and ground plane continuous. Because the PHY is a single-supply device, verify that the MAC interface levels and clock source are compatible with 3.3 V before releasing the schematic, particularly when the host processor uses a different I/O voltage.
Confirm the exact Full MII clocking method, oscillator arrangement, and diagnostic pin requirements for the selected suffix before assigning nets. The family documentation identifies a 25 MHz crystal and, for the KSZ8081RNB, a 50 MHz RMII reference output; those details should not be transferred automatically to every package option. Use the exact manufacturer typical-application circuit and pin-description table to prevent clock-routing or signal-timing mistakes.
The 32-QFN relies on its exposed pad for effective heat transfer. Connect the pad to the recommended ground plane and add thermal vias where the footprint permits, while observing the manufacturer's soldering and via-in-pad guidance. Avoid placing the PHY beside a high-temperature source without recalculating junction temperature. Thermal performance depends on the final PCB copper area, via count, enclosure, and ambient temperature rather than package size alone.
Thông tin tuân thủ
The KSZ8081 is an Ethernet interface IC rather than an automotive-qualified product. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not confirmed for this exact ordering code.