LM224J - 1MHz Quad 32V Op Amp | Texas Instruments
MPN: LM224J ✓ Hoạt độngLM224J Tóm tắt
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify voltage differences. The LM224 belongs to the voltage-feedback operational-amplifier hierarchy and can support closed-loop signal conditioning, sensing, buffering, and control functions. Internally frequency compensation removes the need for an external compensation network in common non-inverting and inverting amplifier configurations.
Key features include four independent amplifier sections, support for single or split supplies, a 1 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. The verified distributor result describes a 32 V maximum supply-related rating, while another result reports operating from approximately ±1.5 V to ±16 V. These ranges describe complementary supply arrangements rather than conflicting absolute limits.
Technically, the LM224J uses a voltage-feedback architecture intended for general-purpose low-frequency signal paths. Its four channels provide useful channel density for multi-axis sensing, multi-channel conditioning, instrumentation, and embedded control. Because the verified results do not provide complete rail-to-rail, input-bias-current, offset-voltage, noise, or common-mode data, engineers should consult the official LM224 datasheet before setting precision or current-budget limits.
Typical uses include transducer buffering, temperature-signal conditioning, low-frequency filtering, industrial control, test equipment, and four-channel sensor interfaces. The 14-CDIP package favors through-hole industrial or legacy-style assemblies rather than compact surface-mount production.
Design with adequate output-current margin, stable feedback compensation for the selected gain and load, and supply-bypass capacitors placed close to the package. Check all electrical limits against the official datasheet, especially when using long feedback traces, high-value resistors, or low-noise sensor interfaces.
This page consolidates distributor availability, verified package and performance details, practical circuit guidance, and replacement analysis that are not presented together in the manufacturer product-page snippet.
Bộ thay thế dễ dàng lắp đặt cho LM224J — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM224J (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Mounting Type, Number of Amplifiers, Supply Configuration.
LM324J
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM124J
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM224J Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General Purpose |
| Number of Amplifiers | 4 circuits |
| Architecture | Voltage Feedback |
| Compensation | Internally Frequency Compensated |
| Maximum Supply Voltage | 32 V |
| Supported Supply Configuration | Single or Split Supply |
| Gain-Bandwidth Product | 1 MHz |
| Mouser-Reported Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Reported Operating Supply Range | ±1.5 V to ±16 V |
| Hộp | 14-CDIP, 0.300 inch, 7.62 mm pitch |
| Số chân | 14 pins |
| Kiểu lắp đặt | Through Hole |
| Temperature Grade | Military temperature |
| Reported Temperature Range | -25 °C to +85 °C |
| Packaging | Tube |
Hướng dẫn cấu hình chân LM224J 14-cdip, 0.300 inch, 7.62 mm pitch
Cấu hình chân cho LM224J (14-cdip, 0.300 inch, 7.62 mm pitch gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM224J.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM224J phù hợp cho 6 Áp dụngs: Four-Channel Sensor Conditioning, Industrial Control and Instrumentation, Temperature Measurement Front End, Low-Frequency Active Filtering, Audio and Low-Level Signal Buffering, Test and Measurement Equipment.
Four-Channel Sensor Conditioning
The LM224J's four amplifier sections allow four low-frequency sensor channels to share one 14-CDIP package, reducing the number of discrete signal-conditioning stages. Its verified 1 MHz gain-bandwidth product and 0.5 V/µs slew rate suit bandwidths well below those limits, while the quad architecture simplifies paired buffering and amplification. The design must still verify input offset, bias current, common-mode range, output swing, and sensor-source impedance in the official datasheet. Keep each feedback loop compact and place supply bypass capacitance close to the device because long PCB traces or excessive feedback resistance can affect accuracy and stability.
Được đề xuất
Industrial Control and Instrumentation
LM224J is suitable as a candidate for low-frequency industrial instrumentation because it integrates four voltage-feedback operational amplifiers and supports single or split supplies. The verified 0.5 V/µs slew rate supports low-frequency control and measurement signals, and the 14-CDIP format is practical for through-hole industrial assemblies. Engineers should account for the complete common-mode and output-swing limits at the selected supply voltage. Feedback-component tolerances and source impedances should also be reviewed because the supplied data does not specify offset voltage or input bias current.
Được đề xuất
Temperature Measurement Front End
A quad LM224J can support several stages in a temperature-measurement front end, including signal amplification, buffering, active filtering, and output conditioning. Its 1 MHz nominal gain-bandwidth product provides margin for low-bandwidth sensors, while four channels reduce repeated package count in multi-point systems. The measured accuracy ultimately depends on verified offset, bias current, resistor accuracy, and sensor excitation, none of which are fully stated in the supplied snippets. Keep high-impedance sensor traces short and inspect datasheet guidance for noise and stability.
Được đề xuất
Low-Frequency Active Filtering
LM224J can implement active low-pass, high-pass, or other closed-loop filtering stages where a 1 MHz gain-bandwidth product and 0.5 V/µs slew rate exceed the signal-frequency requirement. Its internally compensated architecture simplifies basic amplifier stages, but the actual closed-loop bandwidth, allowable noise gain, and capacitive-load behavior must be confirmed in the official datasheet. Choose resistor and capacitor values against those limits rather than the headline bandwidth alone, and keep the feedback node compact to reduce parasitic pickup.
Được đề xuất
Audio and Low-Level Signal Buffering
LM224J can buffer low-level audio-control or instrumentation signals when the operating bandwidth is modest, because the verified 1 MHz gain-bandwidth product exceeds many sub-audio-band applications. The 0.5 V/µs slew rate limits large-signal performance and should be checked against waveform amplitude and frequency. Four channels also permit stereo or multichannel buffering in one through-hole package. For noise-sensitive audio paths, compare the LM224 input-voltage and input-current noise figures in the official datasheet before accepting it as an equal replacement for a dedicated low-noise amplifier.
Được đề xuất
Test and Measurement Equipment
The four channels in LM224J are useful in test and measurement equipment for low-frequency excitation, sensor conditioning, buffering, and active feedback networks. Its through-hole 14-CDIP package supports manual assembly and socket-based prototypes, while the 1 MHz gain-bandwidth product leaves useful margin below audio and instrumentation baseband frequencies. Designers must still verify output-current capability, input bias current, offset, and common-mode limits because those figures were not included in the verified snippets. Stable layout and accessible test points are especially important when multiple channels must interact through external analog circuitry.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM224J — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM324J | LM124J |
|---|---|---|---|
| Package | 14-CDIP, 0.300 inch, 7.62 mm pitch | 14-CDIP family package | 14-CDIP family package |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Type | General Purpose | General Purpose | General Purpose |
| Supply Support | Single or split supply | Single or split supply family description | Single or split supply family description |
Bảo phân biệt quan trọng
- Four independent amplifiers in one legacy through-hole package (vsLM2904N)
- Verified general-purpose bandwidth and slew-rate combination (vsLM324J)
- Single- and split-supply support for flexible legacy power architectures (vsLM124J)
Ghi chú thiết kế
Use short, direct feedback paths and place supply-bypass capacitors at the package supply pins. The LM224J is a through-hole 14-CDIP device, so lead inductance and long analog traces can be especially noticeable at higher closed-loop gains. Keep the common return path continuous and separate from switching-current paths; confirm the exact pinout against the current Texas Instruments datasheet before drilling or wiring the board.
Do not treat 1 MHz as the usable closed-loop bandwidth at every gain. The closed-loop response, gain-bandwidth relationship, output-current capability, noise gain, and capacitive-load stability are separate constraints. Before substituting LM324J or LM124J, compare the official datasheets for pinout, common-mode range, output swing, offset voltage, bias current, slew rate, and temperature grade rather than relying on the shared quad-amplifier description.
For sensor interfaces, keep high-impedance inputs short, shield where appropriate, and avoid routing sensitive inputs beside digital clocks or relay wiring. Check the sensor's source impedance against the input-bias-current specification in the manufacturer datasheet because that value was not included in the verified snippets. Filter only after evaluating the required signal bandwidth; excessive capacitance at the amplifier output can reduce stability.
Thông tin tuân thủ
The verified web data does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. A military temperature rating does not by itself establish AEC-Q100 qualification.
