LM2901DR2 - Quad Open-Collector Comparator | onsemi
MPN: LM2901DR2 ✓ Hoạt độngLM2901DR2 Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901DR2 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Each of its four channels can operate independently, allowing multiple thresholds, window-detection functions, or simple control decisions to be implemented within one device.
The principal features include four comparator channels, a 3 V to 36 V supply range, open-collector outputs, and a typical input bias current of 25 nA. Open-collector outputs provide flexibility when the output must be pulled up to a local supply rail or connected to wired logic. They are not intended to source output current directly, so an external pull-up resistor is normally required.
The LM2901DR2 can operate from a single supply or from split supplies, which makes it adaptable to industrial, automotive, and consumer signal-conditioning circuits. Its differential input arrangement allows one input to act as the reference and the other as the sensed signal. Because this is an analog comparator rather than a logic gate, designers should account for input offset voltage, common-mode range, propagation delay, output pull-up requirements, and supply decoupling when defining switching thresholds.
Typical uses include battery threshold detection, sensor-limit switching, window comparators, level translation, relay or LED drive, automotive interface circuits, and industrial control inputs. A four-channel implementation can also reduce component count when several independent sensing points must be monitored in the same circuit.
When laying out a design, place the bypass capacitor close to the supply pin and route comparator inputs away from switching nodes and high-current paths. Select the pull-up resistor for the required sink current and switching speed, and verify that every input remains inside the device's common-mode range across temperature and supply tolerance. The manufacturer datasheet pin description should be used when assigning PCB tracks.
This product page combines the manufacturer-level electrical characteristics, confirmed SOIC-14 alternatives, sourcing guidance, application analysis, and practical PCB considerations needed to evaluate the LM2901DR2 before incorporating it into a new design.
Bộ thay thế dễ dàng lắp đặt cho LM2901DR2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2901DR2 (cùng hình factor và footprint) — khác nhau ở Comparator Type, Output Type.
LM2901DR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2901M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2901A
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2901DR2 Tỷ lệ tối đa & tính chất điện
| Comparator Type | Quad differential voltage comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| Input Bias Current | 25 nA typical |
| Kiểu đầu ra | Open collector |
| Supply Configuration | Single supply or split supply |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân LM2901DR2 14-pin soic
Cấu hình chân cho LM2901DR2 (14-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2901DR2.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2901DR2 phù hợp cho 6 Áp dụngs: Battery Voltage Threshold Detection, Industrial Sensor Limit Switching, Automotive Level and Window Detection, Window Comparator for Range Monitoring, Open-Collector Logic Interface, Memory and Control Signal Detection.
Battery Voltage Threshold Detection
The LM2901DR2 fits battery threshold detection because it combines four independent comparator channels with a 3 V to 36 V operating supply range. Two channels can establish upper and lower limits for a battery-derived signal, while the remaining channels can supervise auxiliary rails. The open-collector outputs can be pulled up to the voltage used by a controller input, allowing a wired-limit signal without additional output buffers. The typical 25 nA input bias current is useful when the sensed divider has relatively high source impedance. Verify the input common-mode range, offset voltage, and output timing against the battery voltage range before defining the final switching thresholds.
Được đề xuất
Industrial Sensor Limit Switching
For industrial sensor limit switching, the LM2901DR2 can compare a conditioned sensor signal against an adjustable reference and produce an open-collector limit indication. Its four channels allow multiple temperature, pressure, or position sensors to be supervised without using four separate packages. The 25 nA typical input bias current helps preserve the accuracy of high-impedance sensing networks, while the 3 V to 36 V supply range supports common industrial control environments. The external pull-up resistor should be selected for the controller's input voltage and required response speed. Input protection, common-mode headroom, and isolation from switching equipment must also be evaluated in the final analog design.
Được đề xuất
Automotive Level and Window Detection
The LM2901DR2 is applicable to automotive level and window-detection circuits when the specific onsemi ordering code satisfies the required environmental qualification. Four independent channels can supervise tank level, switch position, or other analog thresholds while presenting open-collector status to a vehicle controller. The 3 V to 36 V supply range accommodates common vehicle battery-derived rails, although transient protection remains essential. Designers should confirm the exact input common-mode range, operating temperature, and AEC-Q100 status for the selected ordering code in the manufacturer documentation before using the device in safety-related or qualified automotive applications.
Được đề xuất
Window Comparator for Range Monitoring
A pair of LM2901DR2 channels can implement a window comparator for monitoring a signal that must remain between a lower and upper limit. One channel detects the lower boundary and another detects the upper boundary, with their open-collector outputs feeding a controller input through pull-up resistors. The remaining two channels can perform independent monitoring or fault detection. This arrangement is useful in power-supply supervision, signal-range checking, and sensor diagnostics. Threshold accuracy depends on the reference source and comparator offset voltage, while response time depends on the propagation characteristics and the chosen pull-up network. Both parameters should be checked at the intended supply and temperature conditions.
Được đề xuất
Open-Collector Logic Interface
The LM2901DR2 can interface a low-level analog decision to compatible TTL, CMOS, or wired logic through its open-collector outputs. The output transistor sinks current toward the system ground, while an external pull-up resistor establishes the inactive high level at the desired logic voltage. This arrangement avoids hard-wiring the output to one supply rail and permits different interface domains to share a conventional open-collector bus. The pull-up value must balance rise time against sink-current requirements, and the receiving device must tolerate the selected logic voltage. The manufacturer datasheet should also be consulted for output saturation, current limits, and propagation delay.
Được đề xuất
Memory and Control Signal Detection
The LM2901DR2 supports memory and control-signal detection where a small analog threshold must be translated into a logic-compatible status. Each of its four channels can monitor a separate control line or assist with a memory-related decision, helping reduce package count in compact control assemblies. The 25 nA typical input bias current minimizes loading when signals originate from high-impedance networks, and the open-collector output supports flexible pull-up integration. For reliable operation, confirm that the monitored levels remain inside the common-mode range and that propagation delay is acceptable for the control protocol. Supply bypassing and input routing should be designed to prevent false transitions near the threshold.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2901DR2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2901DR | LM2901M | LM2901A |
|---|---|---|---|---|
| Brand | onsemi | Texas Instruments | onsemi | 3PEAK |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- Four independent channels in one 14-pin SOIC package (vsLM2901A)
- Low typical input bias current (vsLM2901DR)
- Wide 3 V to 36 V operating range (vsLM2901M)
- Open-collector interface flexibility (vsLM2901DR)
Ghi chú thiết kế
Place the supply bypass capacitor immediately adjacent to the comparator supply and ground pins. Keep each comparator's non-inverting and inverting input traces short, and avoid routing them parallel to switching-node or high-current return paths. A compact ground return and separate analog signal routing reduce the chance that supply ripple or switching energy will create false threshold transitions.
Do not operate an open-collector output without a pull-up resistor. Select the resistor to meet the receiver's logic-high requirements while keeping output sink current within its rated limit. A smaller pull-up improves the rising edge, while a larger pull-up reduces sink current; confirm both timing and output-current constraints in the manufacturer datasheet.
Check that every input voltage remains within the LM2901DR2 common-mode range over supply tolerance, signal variation, and temperature. Differential inputs can also be subject to a maximum differential voltage limit. For automotive or industrial equipment, include appropriate transient protection and verify that protection-network leakage does not shift sensitive comparator thresholds.
Treat the four channels as independent decision elements but account for shared supply and ground behavior. Use consistent reference-decoupling practices, especially when several channels switch simultaneously, because supply disturbance can shift thresholds or alter propagation delay. A star-like return near the device and separate high-current paths can improve channel-to-channel repeatability.
Thông tin tuân thủ
The LM2901 family is associated with consumer, automotive, and industrial applications, but exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status for the LM2901DR2 ordering code require confirmation in the manufacturer product or environmental documentation.