LM2901DR2 - Quad Open-Collector Comparator | onsemi
부품 번호: LM2901DR2 ✓ 활성LM2901DR2 개요
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901DR2 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Each of its four channels can operate independently, allowing multiple thresholds, window-detection functions, or simple control decisions to be implemented within one device.
The principal features include four comparator channels, a 3 V to 36 V supply range, open-collector outputs, and a typical input bias current of 25 nA. Open-collector outputs provide flexibility when the output must be pulled up to a local supply rail or connected to wired logic. They are not intended to source output current directly, so an external pull-up resistor is normally required.
The LM2901DR2 can operate from a single supply or from split supplies, which makes it adaptable to industrial, automotive, and consumer signal-conditioning circuits. Its differential input arrangement allows one input to act as the reference and the other as the sensed signal. Because this is an analog comparator rather than a logic gate, designers should account for input offset voltage, common-mode range, propagation delay, output pull-up requirements, and supply decoupling when defining switching thresholds.
Typical uses include battery threshold detection, sensor-limit switching, window comparators, level translation, relay or LED drive, automotive interface circuits, and industrial control inputs. A four-channel implementation can also reduce component count when several independent sensing points must be monitored in the same circuit.
When laying out a design, place the bypass capacitor close to the supply pin and route comparator inputs away from switching nodes and high-current paths. Select the pull-up resistor for the required sink current and switching speed, and verify that every input remains inside the device's common-mode range across temperature and supply tolerance. The manufacturer datasheet pin description should be used when assigning PCB tracks.
This product page combines the manufacturer-level electrical characteristics, confirmed SOIC-14 alternatives, sourcing guidance, application analysis, and practical PCB considerations needed to evaluate the LM2901DR2 before incorporating it into a new design.
드롭인 대체품: LM2901DR2 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2901DR2 (동일 폼 팩터 및 풋프린트) — 차이점: Comparator Type, Output Type.
LM2901DR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2901M
✅ 드롭인가격 문의
데이터시트 보기 →LM2901A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2901DR2 최대 정격 & 전기적 특성
| Comparator Type | Quad differential voltage comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| Input Bias Current | 25 nA typical |
| 출력 유형 | Open collector |
| Supply Configuration | Single supply or split supply |
| 패키지 | 14-pin SOIC |
| 실장 유형 | Surface mount |
LM2901DR2 14-pin soic 핀 구성 가이드
LM2901DR2(14-pin soic 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM2901DR2.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM2901DR2 적합 용도: 6 애플리케이션s: Battery Voltage Threshold Detection, Industrial Sensor Limit Switching, Automotive Level and Window Detection, Window Comparator for Range Monitoring, Open-Collector Logic Interface, Memory and Control Signal Detection.
Battery Voltage Threshold Detection
The LM2901DR2 fits battery threshold detection because it combines four independent comparator channels with a 3 V to 36 V operating supply range. Two channels can establish upper and lower limits for a battery-derived signal, while the remaining channels can supervise auxiliary rails. The open-collector outputs can be pulled up to the voltage used by a controller input, allowing a wired-limit signal without additional output buffers. The typical 25 nA input bias current is useful when the sensed divider has relatively high source impedance. Verify the input common-mode range, offset voltage, and output timing against the battery voltage range before defining the final switching thresholds.
추천
Industrial Sensor Limit Switching
For industrial sensor limit switching, the LM2901DR2 can compare a conditioned sensor signal against an adjustable reference and produce an open-collector limit indication. Its four channels allow multiple temperature, pressure, or position sensors to be supervised without using four separate packages. The 25 nA typical input bias current helps preserve the accuracy of high-impedance sensing networks, while the 3 V to 36 V supply range supports common industrial control environments. The external pull-up resistor should be selected for the controller's input voltage and required response speed. Input protection, common-mode headroom, and isolation from switching equipment must also be evaluated in the final analog design.
추천
Automotive Level and Window Detection
The LM2901DR2 is applicable to automotive level and window-detection circuits when the specific onsemi ordering code satisfies the required environmental qualification. Four independent channels can supervise tank level, switch position, or other analog thresholds while presenting open-collector status to a vehicle controller. The 3 V to 36 V supply range accommodates common vehicle battery-derived rails, although transient protection remains essential. Designers should confirm the exact input common-mode range, operating temperature, and AEC-Q100 status for the selected ordering code in the manufacturer documentation before using the device in safety-related or qualified automotive applications.
추천
Window Comparator for Range Monitoring
A pair of LM2901DR2 channels can implement a window comparator for monitoring a signal that must remain between a lower and upper limit. One channel detects the lower boundary and another detects the upper boundary, with their open-collector outputs feeding a controller input through pull-up resistors. The remaining two channels can perform independent monitoring or fault detection. This arrangement is useful in power-supply supervision, signal-range checking, and sensor diagnostics. Threshold accuracy depends on the reference source and comparator offset voltage, while response time depends on the propagation characteristics and the chosen pull-up network. Both parameters should be checked at the intended supply and temperature conditions.
추천
Open-Collector Logic Interface
The LM2901DR2 can interface a low-level analog decision to compatible TTL, CMOS, or wired logic through its open-collector outputs. The output transistor sinks current toward the system ground, while an external pull-up resistor establishes the inactive high level at the desired logic voltage. This arrangement avoids hard-wiring the output to one supply rail and permits different interface domains to share a conventional open-collector bus. The pull-up value must balance rise time against sink-current requirements, and the receiving device must tolerate the selected logic voltage. The manufacturer datasheet should also be consulted for output saturation, current limits, and propagation delay.
추천
Memory and Control Signal Detection
The LM2901DR2 supports memory and control-signal detection where a small analog threshold must be translated into a logic-compatible status. Each of its four channels can monitor a separate control line or assist with a memory-related decision, helping reduce package count in compact control assemblies. The 25 nA typical input bias current minimizes loading when signals originate from high-impedance networks, and the open-collector output supports flexible pull-up integration. For reliable operation, confirm that the monitored levels remain inside the common-mode range and that propagation delay is acceptable for the control protocol. Supply bypassing and input routing should be designed to prevent false transitions near the threshold.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2901DR2 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2901DR | LM2901M | LM2901A |
|---|---|---|---|---|
| Brand | onsemi | Texas Instruments | onsemi | 3PEAK |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
주요 차별점
- Four independent channels in one 14-pin SOIC package (vs LM2901A)
- Low typical input bias current (vs LM2901DR)
- Wide 3 V to 36 V operating range (vs LM2901M)
- Open-collector interface flexibility (vs LM2901DR)
설계 노트
Place the supply bypass capacitor immediately adjacent to the comparator supply and ground pins. Keep each comparator's non-inverting and inverting input traces short, and avoid routing them parallel to switching-node or high-current return paths. A compact ground return and separate analog signal routing reduce the chance that supply ripple or switching energy will create false threshold transitions.
Do not operate an open-collector output without a pull-up resistor. Select the resistor to meet the receiver's logic-high requirements while keeping output sink current within its rated limit. A smaller pull-up improves the rising edge, while a larger pull-up reduces sink current; confirm both timing and output-current constraints in the manufacturer datasheet.
Check that every input voltage remains within the LM2901DR2 common-mode range over supply tolerance, signal variation, and temperature. Differential inputs can also be subject to a maximum differential voltage limit. For automotive or industrial equipment, include appropriate transient protection and verify that protection-network leakage does not shift sensitive comparator thresholds.
Treat the four channels as independent decision elements but account for shared supply and ground behavior. Use consistent reference-decoupling practices, especially when several channels switch simultaneously, because supply disturbance can shift thresholds or alter propagation delay. A star-like return near the device and separate high-current paths can improve channel-to-channel repeatability.
규정 준수 정보
The LM2901 family is associated with consumer, automotive, and industrial applications, but exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status for the LM2901DR2 ordering code require confirmation in the manufacturer product or environmental documentation.