LM2902KVQDR - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM2902KVQDR ✓ Hoạt độngLM2902KVQDR Tóm tắt
An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses high open-loop gain to amplify the difference between two input voltages. The quad operational-amplifier category combines four amplifiers in one package, reducing board area compared with four separate single amplifiers. LM2902-family devices belong to the broader operational-amplifier, analog-signal, and semiconductor hierarchies.
The LM2902KVQDR provides four independent, internally frequency-compensated amplifiers with a 1.2 MHz gain-bandwidth product. Its 30 V supply capability supports higher-voltage industrial and instrumentation circuits than the 26 V LM2902K family. Improved 2 kV ESD protection adds robustness when exposed to electrostatic discharge during handling or operation. The quad configuration is useful for amplifier arrays, sensor interfaces, active filters, and differential signal-conditioning channels.
Operation from a single supply allows the input and output signals to remain close to ground, while split-supply operation supports bipolar signals around a midpoint. Each amplifier can be configured independently for noninverting, inverting, summing, comparator-style, or feedback-amplifier applications. The 14-pin SOIC package supports conventional surface-mount assembly and broad compatibility with industrial control and analog-instrumentation designs.
Typical applications include four-channel sensor conditioning, active low-pass and band-pass filters, bridge-signal amplifiers, differential measurement front ends, audio preamplifier blocks, and general-purpose analog signal chains. The four-amplifier architecture is particularly useful when several channels require similar conditioning without allocating separate packages.
When designing around the LM2902KVQDR, verify input and output common-mode limits across the complete supply range and use stable compensation for capacitive loads. Place input and feedback components close to their associated pins to reduce parasitic capacitance and preserve the expected 1.2 MHz bandwidth.
This page combines the manufacturer device description, technical characteristics, package information, qualified drop-in alternatives, and practical design guidance for engineers evaluating the LM2902KVQDR in multi-channel analog systems.
Bộ thay thế dễ dàng lắp đặt cho LM2902KVQDR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2902KVQDR (cùng hình factor và footprint) — khác nhau ở Package, Maximum Supply Voltage, Amplifier Type, Input Offset Voltage, Number of Channels.
LM2902KDBR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2902KNSR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2902VDG
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2902DG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2902DTB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2902KVQDR Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 amplifiers |
| Number of Circuits | 4 circuits |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Improved ESD Protection | 2 kV |
| Khoảng nhiệt độ hoạt động | -40°C to +125°C |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Input Offset Voltage | 600 µV typical |
| Common-Mode Input Range | To ground |
| Differential Input Voltage Capability | High differential input voltage capability |
| Supply Configuration | Single supply or split supply |
| Compensation | Internally frequency compensated |
| Channel Independence | 4 independent amplifiers |
Cấu hình chân LM2902KVQDR
| Chân 1 | OUT1 — Amplifier 1 output |
| Chân 2 | -IN1 — Amplifier 1 inverting input |
| Chân 3 | +IN1 — Amplifier 1 noninverting input |
| Chân 4 | V+ — Positive supply connection |
| Chân 5 | +IN2 — Amplifier 2 noninverting input |
| Chân 6 | -IN2 — Amplifier 2 inverting input |
| Chân 7 | OUT2 — Amplifier 2 output |
| Chân 8 | OUT3 — Amplifier 3 output |
| Chân 9 | -IN3 — Amplifier 3 inverting input |
| Chân 10 | +IN3 — Amplifier 3 noninverting input |
| Chân 11 | V- — Negative supply connection |
| Chân 12 | +IN4 — Amplifier 4 noninverting input |
| Chân 13 | -IN4 — Amplifier 4 inverting input |
| Chân 14 | OUT4 — Amplifier 4 output |
Ứng dụng tiêu biểu
LM2902KVQDR phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Active Audio and Low-Frequency Filters, Power-Supply Monitoring and Control, Data Acquisition Front End, Bridge and Transducer Amplification, Automotive and Heavy Equipment Electronics.
Industrial Sensor Signal Conditioning
The LM2902KVQDR fits multi-channel industrial sensor conditioning because it provides four independent amplifiers in one 14-pin SOIC package. Its 30 V maximum supply rating supports higher-voltage instrumentation than the 26 V LM2902K family, while the -40°C to +125°C range covers demanding factory environments. Each channel can amplify a transducer output, scale a bridge signal, or provide active filtering. The 1.2 MHz gain-bandwidth product is suitable for low- and mid-bandwidth process signals, although the selected gain must preserve stability and bandwidth. Check common-mode voltage, output swing, offset error, and sensor grounding for every channel.
Được đề xuất
Active Audio and Low-Frequency Filters
The LM2902KVQDR can implement four sections of an active filter or several independent audio preamplifier paths because every amplifier is independently usable. Its 1.2 MHz gain-bandwidth product supports low-frequency amplification, tone control, crossover, and anti-alias filtering where higher audio frequencies are not required. The quad SOIC package reduces component count and simplifies routing compared with four separate single-amplifier packages. With a 30 V supply rating, the device can also operate in higher-voltage line-level or balanced audio circuits, provided the actual output swing remains inside the specified range. Stable feedback design and appropriate source and load impedances are essential for clean audio performance.
Được đề xuất
Power-Supply Monitoring and Control
The LM2902KVQDR is appropriate for supervisory and power-control circuitry that compares multiple regulated or divided voltages against references. Four independent amplifiers can monitor separate rails, amplify error signals, or form gain stages around power-control comparators. Its 30 V maximum supply rating and 1.2 MHz bandwidth provide useful headroom for supervisory loops and transient-related control functions. Because the common-mode input range reaches ground, low-side voltage monitoring is practical. Designers should still verify the permitted input and output excursions, account for typical 600 µV input offset, and avoid using the amplifier outside its linear output region when it is intended as a comparator.
Được đề xuất
Data Acquisition Front End
The LM2902KVQDR can provide conditioning for several low-speed acquisition channels using differential amplification, active anti-alias filtering, and gain stages. A 1.2 MHz gain-bandwidth product supports signals well below the converter sample rate in many measurement systems, while four amplifiers allow differential pairs to be implemented without using four packages. The -40°C to +125°C operating range supports industrial equipment, and the 30 V supply capability can simplify interface arrangements around higher-voltage signal chains. For accurate measurements, verify the input offset, common-mode range, noise behavior, settling time at the selected closed-loop gain, and interaction with the converter input network.
Được đề xuất
Bridge and Transducer Amplification
The LM2902KVQDR is well suited to bridge and transducer interfaces that need differential gain, where two amplifiers form a complete differential stage and the remaining channels handle reference or auxiliary functions. Its common-mode input range extending to ground supports low-side sensing arrangements, while the 30 V supply rating accommodates instrumentation built around elevated excitation or bias voltages. The quad SOIC package keeps the analog front end compact and can reduce board-space requirements. Confirm that the bridge excitation and signal amplitudes remain within the amplifier’s common-mode and differential-input limits, and use resistors and layout techniques that preserve differential accuracy.
Được đề xuất
Automotive and Heavy Equipment Electronics
The LM2902KVQDR can serve low-frequency analog functions in automotive or heavy-equipment modules where a wide temperature range and four-channel integration are useful. The -40°C to +125°C operating range and improved 2 kV ESD protection support harsh environments, while the 14-pin SOIC package is practical for cost-sensitive control boards. The four amplifiers can handle sensor amplification, actuator-driver feedback, filtering, and voltage monitoring. The LM2902KV family is not automatically equivalent to an AEC-Q100-qualified order code, so qualification status, electromagnetic requirements, transient protection, and production traceability must be reviewed separately before use in safety-relevant automotive electronics.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2902KVQDR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2902KDBR | LM2902KNSR | LM2902VDG | LM2902DG | LM2902DT |
|---|---|---|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Quad | Quad | Quad | Quad | Quad | Quad |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
Bảo phân biệt quan trọng
- Higher maximum supply rating within the LM2902 family (vsLM2902KDBR)
- Four independent amplifiers in one compact package (vsLM2902DG)
- Improved ESD protection combined with extended temperature operation (vsLM2902DT)
- 1.2 MHz bandwidth with a 30 V supply rating (vsLM2902KNSR)
Ghi chú thiết kế
Route each amplifier channel so that input, feedback, and output traces remain short and are not forced around unrelated switching stages. The 1.2 MHz gain-bandwidth product benefits from minimized parasitic capacitance, particularly at high closed-loop gain. Keep the SOIC footprint and copper clearances consistent with the manufacturer’s package drawing, and avoid placing test-point capacitance directly across high-impedance inputs unless its effect has been evaluated.
Do not assume that a 30 V maximum supply rating permits unrestricted input or output voltages. Confirm the complete common-mode input range, differential input limit, and output swing for the actual supply and load. The common-mode range extends to ground, which is useful for low-side sensing, but it does not eliminate upper-range restrictions. Also account for the typical 600 µV input offset when precision measurement performance depends on gain and calibration.
The LM2902KVQDR supports single-supply or split-supply operation, so its total supply voltage and each rail must remain within the device limits. Place supply-bypass capacitors close to pins 4 and 11, and keep the return-current path short to reduce supply noise and output instability. When four channels operate simultaneously, evaluate aggregate output-current demand, source impedance, and thermal rise under the worst-case output configuration.
Check stability with the actual source impedance, load capacitance, feedback resistor values, and PCB parasitics. Long feedback tracks or excessive capacitive loading can reduce phase margin even though the amplifier has a 1.2 MHz nominal gain-bandwidth product. For active filters, calculate each resistor and capacitor against the target gain and corner frequency, then verify channel-to-channel behavior with the intended supply and signal ranges.
Thông tin tuân thủ
The available product description identifies the 30 V, 1.2 MHz, improved 2 kV ESD and -40°C to +125°C characteristics but does not provide explicit material-compliance or automotive-qualification declarations for the exact ordering code.