LM2903M/SL160222 - Dual Differential Comparator | Texas Instruments
MPN: LM2903M/SL160222 ✓ Hoạt độngLM2903M/SL160222 Tóm tắt
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category sits within analog signal-processing ICs, alongside amplifiers and voltage references, while remaining distinct from a general-purpose operational amplifier. The LM2903 architecture combines two independent channels in one package, reducing board area when two comparison functions are required.
The LM2903 family is designed to operate from a single power supply over a wide voltage range. According to the manufacturer datasheet, the offset voltage can be specified as low as 2.0 mV maximum for the two-comparator configuration. Open-collector outputs permit wired connections to pull-up circuitry and provide a flexible interface to TTL, MOS, and CMOS-compatible systems. Each channel offers separate inverting, non-inverting, and output terminals.
Because the two sections are electrically independent, engineers can use one channel for a sensor threshold and the second for a system interlock or control signal. The single-supply architecture is useful in equipment where one supply rail defines the comparator signal domain. Input and output operating conditions, channel-to-channel behavior, supply-current characteristics, and absolute maximum ratings should be checked against the exact manufacturer ordering information before production release.
Typical applications include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, motor-control logic, window comparators, and digital threshold conditioning. In each case, open-collector outputs can drive a pull-up and logic gate, or serve as an active-low alert signal. The small SOIC footprint also supports compact control boards where two independent channels are valuable.
For robust layouts, route comparator inputs away from switching nodes and power inductors, place input-referred bypassing close to the supply pin, and pull each open-collector output up to the appropriate logic supply. Check that the pull-up voltage, input common-mode range, supply voltage, and output sink-current requirement satisfy the application before substituting this part into an existing design.
This page consolidates the exact LM2903M/SL160222 ordering information, verified manufacturer and distributor references, pin assignments, drop-in alternatives, and practical application guidance to accelerate schematic review, PCB reuse, sourcing, and replacement planning.
Bộ thay thế dễ dàng lắp đặt cho LM2903M/SL160222 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903M/SL160222 (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature Range, Propagation Delay, Comparator Type, Output Type.
LM2903M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903M/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903M/SL160222 Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 |
| Architecture | Two independent precision voltage comparators |
| Supply Configuration | Single supply |
| Input Offset Voltage | 2.0 mV maximum for two comparators |
| Kiểu đầu ra | Open-collector |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Output Compatibility | TTL, MOS, and CMOS compatible |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Cấu hình chân LM2903M/SL160222
| Chân 1 | OUT 1 — Open-collector output for comparator channel 1 |
| Chân 2 | IN 1- — Inverting input for comparator channel 1 |
| Chân 3 | IN 1+ — Non-inverting input for comparator channel 1 |
| Chân 4 | GND — Ground reference |
| Chân 5 | IN 2+ — Non-inverting input for comparator channel 2 |
| Chân 6 | IN 2- — Inverting input for comparator channel 2 |
| Chân 7 | OUT 2 — Open-collector output for comparator channel 2 |
| Chân 8 | VCC — Positive power supply |
Ứng dụng tiêu biểu
LM2903M/SL160222 phù hợp cho 6 Áp dụngs: Industrial Sensor Threshold Detection, Battery Monitoring and Low-Voltage Alert, Motor-Control and Overcurrent Protection Logic, Window Comparator for Signal Qualification, Open-Collector Alarm and System Interlock, General-Purpose Logic Interface.
Industrial Sensor Threshold Detection
The LM2903M/SL160222 fits industrial sensor interfaces that require two independent decisions within one 8-pin SOIC package. One channel can compare a conditioned sensor voltage with an adjustable reference, while the second monitors a separate limit or fault signal. According to the Texas Instruments manufacturer datasheet, the family is designed for single-supply operation and can provide an input offset voltage as low as 2.0 mV maximum for the two-comparator configuration. Open-collector outputs suit active-low PLC or controller inputs when paired with suitable pull-up resistors. Place the part away from motor switching nodes, use a stable reference for the decision threshold, and verify the common-mode range across the complete sensor and supply operating range.
Được đề xuất
Battery Monitoring and Low-Voltage Alert
The LM2903M/SL160222 is suitable for battery-powered monitoring circuits that compare a divided battery voltage against a reference and generate an active-low alert. Its two independent comparator channels can supervise separate voltage thresholds without requiring two packages, while the documented single-supply architecture supports compact power systems. The Texas Instruments manufacturer datasheet describes the device as two independent precision voltage comparators with offset voltage as low as 2.0 mV maximum for the two-comparator configuration. Open-collector outputs allow a pull-up to the local logic rail, although the resistor can consume continuous current while the output is low. Select divider tolerances and a low-current reference to prevent threshold drift, then verify the full battery discharge range against the comparator input limits.
Được đề xuất
Motor-Control and Overcurrent Protection Logic
The LM2903M/SL160222 can implement hardware decision logic around a motor-control or power-conversion subsystem by comparing a current-sense signal with a trip reference. Two independent channels allow separate monitoring functions, such as a fast overcurrent channel and a slower thermal or supply-condition channel. The Texas Instruments manufacturer datasheet identifies open-collector outputs and single-supply operation as central family characteristics, allowing each comparator to drive a gate-driver fault input, relay, or status latch through suitable interface circuitry. Keep the sense path short and isolate it from high-current switching nodes to preserve threshold accuracy. Confirm output-current capacity, input recovery behavior, and supply limits under the worst operating condition before using the comparator as a protective element.
Được đề xuất
Window Comparator for Signal Qualification
The LM2903M/SL160222 can implement a window-comparator arrangement by using its two independent channels to detect both an upper and a lower threshold. This is useful for validating a conditioned analog signal before passing it to an ADC, logic system, or actuator. The manufacturer datasheet specifies an offset voltage as low as 2.0 mV maximum for the two-comparator configuration, helping define the practical threshold separation when signal levels permit. Because the outputs are open-collector, their active-low states can be combined with pull-ups and logic gates to create an in-range indication. Keep both threshold networks close to the device, use matched reference impedances where threshold drift matters, and test the complete signal amplitude against both comparators for overlap and hysteresis behavior.
Được đề xuất
Open-Collector Alarm and System Interlock
The LM2903M/SL160222 fits alarm and interlock circuits where a fault condition must pull a shared line low. One channel can monitor a fault flag while the second verifies an enable, reset, or healthy-state signal. Open-collector outputs provide wired logic behavior when each output receives its own pull-up, and the two channels allow separate fault paths to remain electrically independent. According to the Texas Instruments LM2903 documentation, the outputs are compatible with TTL, MOS, and CMOS systems. Select the pull-up voltage for the receiving logic and calculate its maximum current from the output-low specification. For safety-related use, review redundancy, fail-safe polarity, response time, and applicable system requirements rather than relying on comparator qualification alone.
Được đề xuất
General-Purpose Logic Interface
The LM2903M/SL160222 can bridge a slowly changing analog indication to a digital control system by comparing the indication with a logic threshold. The open-collector output can operate an indicator, optocoupler input, relay driver, or controller enable after adding the required pull-up and any necessary transistor stage. The manufacturer datasheet confirms single-supply operation, two independent comparator sections, and TTL, MOS, and CMOS interface compatibility. This makes the device suitable for legacy equipment where a compact, discrete-channel alternative is preferable. Ensure the compared signal remains within the common-mode limits at every supply voltage, account for input offset in threshold design, and include hysteresis where chatter near the threshold could otherwise cause repeated transitions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2903M/SL160222 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2903M | LM2903M/NOPB | LM2903BIDR | LM2903B | LM2903M |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Comparator Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Ordering Configuration | LM2903M/SL160222 customer-specific designation | Base LM2903M designation | NOPB ordering designation | B-version, SOIC reel designation | B-version family designation | onsemi manufacturer designation |
Bảo phân biệt quan trọng
- Two independent comparator channels in one 8-pin SOIC (vsLM2901DRG4)
- Documented low offset for dual-channel operation (vsonsemi LM2903M)
- Open-collector interface flexibility (vsLM2901DRG4)
Ghi chú thiết kế
Route the inverting and non-inverting inputs as a compact, matched pair and keep them away from relay contacts, switching-regulator outputs, and high-current power traces. Place the supply bypass capacitor close to pin 8 and connect pin 4 to the quiet ground reference. Because the LM2903M/SL160222 uses open-collector outputs, place each pull-up resistor near the corresponding output or receiving logic input so that switching trace length and parasitic capacitance remain small.
Do not treat an open-collector output as a push-pull logic output. Each output requires a pull-up to the appropriate logic rail, and the resulting high level is set by that supply rather than by the comparator. Check the output-low voltage at the intended sink current, verify the logic-family input thresholds, and account for the continuous pull-up current while the output is low. A missing or incorrectly selected pull-up can prevent the downstream device from recognizing the valid high state.
Design threshold comparisons with realistic noise margin rather than relying only on the nominal reference voltage. The manufacturer datasheet documents an offset voltage as low as 2.0 mV maximum for the two-comparator configuration, but input offset alone does not define system accuracy. Reference tolerance, resistor tolerance, temperature drift, input noise, and propagation delay can all move the switching point. Add intentional hysteresis when the compared signal can cross the threshold slowly or exhibit noise near the decision boundary.
Thông tin tuân thủ
The retrieved LM2903 family references do not explicitly state compliance for the exact LM2903M/SL160222 ordering designation. Confirm current material declarations with Texas Instruments for the exact orderable code.