LM293DMR2 - Dual Precision Comparator, 36 V | onsemi
MPN: LM293DMR2 ✓ Hoạt độngLM293DMR2 Tóm tắt
A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital logic state at its output. The LM293 belongs to the comparator hierarchy, which includes differential comparators, window comparators, and precision comparators. By converting an analog threshold relationship into an open-collector logic indication, this type of device bridges analog measurement circuits and digital control, monitoring, or protection systems.
The principal features include two independent comparators, low offset voltage, a common-mode input range extending to ground under single-supply operation, and open-collector outputs that can sink current from multiple compatible devices. The 2 V to 36 V operating supply range accommodates 5 V, 12 V, and 24 V systems. The onsemi datasheet also identifies the device as suitable for consumer, automotive, and industrial applications where reliable voltage-level detection is required.
Each comparator channel is independent, allowing one device to perform two unrelated threshold measurements. The open-collector architecture requires an external pull-up resistor and provides a wired-output capability when several comparator outputs share a bus. This architecture does not actively drive the output high, but it offers flexible voltage-level adaptation and enables wired-AND behavior when output collectors are connected.
Typical uses include monitoring a 12 V or 24 V automotive battery, detecting overvoltage and undervoltage conditions in industrial power systems, comparing sensor outputs with adjustable thresholds, and providing simple supervisory functions in consumer equipment. The grounded common-mode capability is especially useful in single-supply systems where the signal of interest begins near 0 V and cannot be compared reliably by a comparator with a restricted input range.
For robust PCB implementation, place input resistors close to the comparator pins to limit differential pickup and route the inputs away from switching nodes and high-current paths. Select the external output pull-up for the intended logic voltage, and confirm that its maximum sink current remains within the device output ratings. Check that the common-mode and differential input voltages remain within the absolute maximum limits during power transients.
This product page combines the manufacturer specifications, package and pin information, drop-in replacement analysis, comparison data, and practical PCB guidance to accelerate design review and sourcing. The technical recommendations focus on preserving the LM293DMR2 role as a reliable, low-offset dual comparator while making package, electrical, and supply constraints explicit before layout release.
Bộ thay thế dễ dàng lắp đặt cho LM293DMR2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM293DMR2 (cùng hình factor và footprint) — khác nhau ở Package, Comparator Type, Input Offset Voltage, Output Type.
LM293DMR2G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393DMR2G
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2903DMR2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM293DMR2 Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual independent precision voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Split Supply Rating | ±18 V |
| Input Offset Voltage | 2.0 mV maximum |
| Kiểu đầu ra | Open-collector |
| Common-Mode Operation | Rail-to-rail input with single-supply operation |
| Operating Supply Mode | Single or split supply |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| Hộp | TSSOP-8 |
| Kiểu lắp đặt | Surface mount |
| Manufacturer Description | Dual low-offset voltage comparator |
| Automotive Application Suitability | Automotive applications |
| Industrial Application Suitability | Industrial applications |
| Consumer Application Suitability | Consumer applications |
| Output Pull-Up Requirement | External pull-up resistor required |
Cấu hình chân LM293DMR2
| Chân 1 | OUT 1 — Comparator 1 open-collector output |
| Chân 2 | IN 1- — Comparator 1 inverting input |
| Chân 3 | IN 1+ — Comparator 1 noninverting input |
| Chân 4 | GND — Ground connection |
| Chân 5 | IN 2+ — Comparator 2 noninverting input |
| Chân 6 | IN 2- — Comparator 2 inverting input |
| Chân 7 | OUT 2 — Comparator 2 open-collector output |
| Chân 8 | VCC — Positive supply connection |
Ứng dụng tiêu biểu
LM293DMR2 phù hợp cho 6 Áp dụngs: Automotive Battery Monitoring, Industrial Overvoltage Protection, Battery Charger Status Detection, Sensor Interface Thresholding, Consumer Power Sequencing, Security and Surveillance Interface.
Automotive Battery Monitoring
The LM293DMR2 fits automotive battery-threshold monitoring because its 2 V to 36 V supply range accommodates nominal 12 V and 24 V systems, while the 2.0 mV input offset supports tighter switching thresholds than a general-purpose comparator. Place one channel near an overvoltage threshold and the other near an undervoltage threshold, with the noninverting and inverting inputs set by a resistor network. Each open-collector output can drive a pull-up and an indicator or controller input. The design must add transient suppression and verify that fault voltages cannot exceed the device input limits.
Được đề xuất
Industrial Overvoltage Protection
The LM293DMR2 can supervise a 12 V or 24 V industrial power rail by comparing its divided voltage with a precision reference. Its 2.0 mV maximum input offset improves threshold repeatability, and the 2 V to 36 V operating supply covers common industrial rails. One comparator channel can detect an overvoltage condition, while the second can provide undervoltage or window supervision. Use the open-collector output to pull down an enable line or illuminate a fault signal through an external pull-up. Account for relay transients, surge paths, and the limited input range during fault analysis.
Được đề xuất
Battery Charger Status Detection
The LM293DMR2 is useful for comparing divided battery voltages against charge thresholds in portable and industrial charging systems. The 2 V minimum operating supply allows operation from a reduced auxiliary rail, and the 2.0 mV offset helps preserve accuracy after resistive voltage division. Two independent channels can identify separate charge or discharge thresholds, producing open-collector logic for a charger state machine. Select resistor values to keep the input common-mode voltage within the permitted range and choose a pull-up voltage compatible with the downstream logic. Add filtering when the monitored source contains ripple.
Được đề xuất
Sensor Interface Thresholding
The LM293DMR2 converts an analog sensor signal into a logic indication when the signal crosses a defined threshold. Its low 2.0 mV offset is valuable when the input is derived from a resistive divider, and single-supply operation permits comparison with signals near ground. Use the two channels for two sensor thresholds or configure one as a hysteretic comparator with positive feedback. The open-collector output supports a flexible pull-up voltage and can trigger a microcontroller input or gate. Keep sensor traces away from switching power nodes and add filtering when the measured quantity changes slowly or contains noise.
Được đề xuất
Consumer Power Sequencing
The LM293DMR2 can supervise a power rail and provide a permissive or fault signal during consumer-system startup. Its 2 V to 36 V supply range supports both low-voltage logic rails and larger 12 V systems, while the two channels can monitor independent sequence thresholds. Open-collector outputs make it straightforward to combine a fault indication with a pull-up network and downstream enable logic. Confirm the input common-mode range during ramp-up and add hysteresis to prevent repeated enable toggling near the threshold. The TSSOP-8 footprint also supports compact consumer boards where two separate comparator packages would be impractical.
Được đề xuất
Security and Surveillance Interface
The LM293DMR2 fits security and surveillance interfaces that require reliable detection of a contact, resistive sensor, or divided supply condition. Two channels can monitor independent alarm points, and the open-collector output can pull down a wired alarm line through a suitable pull-up. The 2.0 mV offset class helps preserve repeatability around carefully chosen thresholds, while the 2 V to 36 V supply accommodates both logic and higher-voltage monitoring circuits. Provide input filtering for long cable runs, protect exposed nodes from transients, and observe absolute-maximum differential input limits to avoid damage during contact closure.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM293DMR2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM293DMR2G | LM393DMR2 | LM2903DMR2 |
|---|---|---|---|---|
| Package | TSSOP-8 | TSSOP-8 | TSSOP-8 | TSSOP-8 |
| Brand | onsemi | onsemi | onsemi | onsemi |
| Comparator Channels | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Split Supply Rating | ±18 V | ±18 V | ±18 V | ±18 V |
| Maximum Input Offset Voltage | 2.0 mV | 2.0 mV | Approximately 5 mV | 2.0 mV |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
| Supply Mode | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
Bảo phân biệt quan trọng
- Lower maximum input offset in the directly comparable LM393 option (vsLM393DMR2)
- Same-family suffix alternative preserves the core electrical ratings (vsLM293DMR2G)
- Broader temperature coverage in the automotive comparison (vsLM2903DMR2)
Ghi chú thiết kế
Do not treat the open-collector output as a push-pull logic output. Fit an external pull-up resistor to every output that must reach a valid high state, and confirm that the resistor, logic supply, and output sink current form a valid combination. When multiple outputs are wired together, calculate the maximum total sink current under the worst-case state. Also verify the absolute maximum differential input voltage during startup and fault conditions, because input protection is not intended to handle unrestricted overloads.
Place input-setting and feedback resistors close to pins 2, 3, 5, and 6 to minimize parasitic capacitance and susceptibility to coupled noise. Route both comparison inputs as a compact differential pair where practical, and keep them away from inductors, switching-node copper, and high-current return paths. Because threshold accuracy can be affected by input offset and noise, avoid sharing long exposed input runs with unrelated analog signals. The GND connection should use a short return to the circuit reference plane.
Decouple the supply pin close to the device with a local ceramic capacitor and provide adequate bulk capacitance for the connected circuit. The supported 2 V to 36 V range does not remove the need for supply filtering because comparator propagation behavior and input thresholds can be influenced by supply ripple. For automotive or industrial rails, include transient and reverse-polarity protection ahead of the IC. Confirm that protection-network leakage does not move a high-impedance sensing node outside the comparator's common-mode range.
Use hysteresis when the compared signal crosses the threshold slowly or contains noise, otherwise the open-collector output can chatter and repeatedly trigger downstream circuitry. Positive feedback from output to the appropriate input creates hysteresis, but the added path must be sized against the resistor network that establishes the threshold. For slowly varying battery or temperature signals, add filtering at the input while preserving comparator response time. Validate the final threshold, noise margin, and propagation delay with worst-case component tolerances.
Thông tin tuân thủ
The manufacturer documents identify automotive suitability but do not explicitly establish the orderable LM293DMR2 as AEC-Q100 qualified. Compliance attributes for this exact suffix require confirmation from onsemi.