LM324ADE4 - Quad 1.2MHz Op Amp | Texas Instruments | SOIC-14
MPN: LM324ADE4 ✓ Hoạt độngLM324ADE4 Tóm tắt
An operational amplifier is an analog signal-conditioning IC that compares two input voltages and amplifies their difference through high open-loop gain. The LM324ADE4 belongs to the operational-amplifier hierarchy within amplifier ICs and analog semiconductors. Its four independent channels allow one package to provide feedback control, buffering, level shifting, summation, and general analog amplification without requiring four separate amplifier packages.
The four amplifiers feature internally frequency compensation, allowing operation as stable unity-gain buffers without external compensation components. A 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate support audio-band and general-purpose closed-loop applications. The device also supports operation from a single positive supply as well as split bipolar supplies, making it useful in mixed industrial, instrumentation, control, and consumer circuits.
The 14-SOIC package is pin-compatible with the established LM324 family arrangement, which simplifies repair, prototyping, and board reuse. Each amplifier has differential inputs, an output, and power connections, with the package distributing those functions across four channels. Because the amplifiers are independent rather than sharing internal output stages, each channel can be used for a separate signal path or left unused when its input and output are properly configured.
Typical uses include sensor-signal conditioning, low-current motor and actuator drivers, audio preamplification, analog summing networks, threshold detection, and general instrumentation. The 1.2 MHz bandwidth is adequate for many audio and control signals, but designs requiring substantially higher bandwidth, lower offset voltage, faster settling, or lower noise should use a more specialized amplifier family.
Design carefully around input common-mode range, output swing, input bias current, and the limits of each amplifier channel. Keep sensitive inputs away from noisy return paths, observe the recommended bypass capacitors at the supply pins, and avoid operating near the output saturation limits. The manufacturer datasheet should guide input/output protection, supply decoupling, unused-channel configuration, and maximum input and output voltage conditions.
This product page combines the LM324ADE4 operating parameters, package details, practical application guidance, pin-focused design considerations, and qualified drop-in alternatives. It is intended to help engineers identify where this economical quad general-purpose amplifier fits and where a higher-performance or application-specific amplifier is more appropriate.
Bộ thay thế dễ dàng lắp đặt cho LM324ADE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM324ADE4 (cùng hình factor và footprint) — khác nhau ở Package, Number of Amplifiers.
LM324AD
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324KADG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM324ADE4 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 independent channels |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Supply Voltage Range | Single supply or split supply up to ±16 V |
| Minimum Total Supply Voltage | 3 V |
| Maximum Total Supply Voltage | 32 V |
| Frequency Compensation | Internally compensated |
| Hộp | 14-SOIC (14 pins) |
| Package Width | 3.90 mm |
| Kiểu lắp đặt | Surface mount |
| Số lượng đầu ra | 4 outputs |
Hướng dẫn cấu hình chân LM324ADE4 3.90 mm
Cấu hình chân cho LM324ADE4 (3.90 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM324ADE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM324ADE4 phù hợp cho 6 Áp dụngs: Sensor Signal Conditioning, Audio Preamplification, Industrial Control Loops, Buffering and Level Shifting, Threshold Detection and Relay Logic, Test and Measurement Front Ends.
Sensor Signal Conditioning
The LM324ADE4 is suitable for conditioning outputs from slow analog sensors because each of its four internally compensated channels can amplify a small differential signal referenced close to ground. The 1.2 MHz gain-bandwidth product supports closed-loop gains that do not require more bandwidth than the sensor path can deliver. Use one channel for amplification and another for an offset or threshold stage, while observing the input common-mode limits. On a 5 V single supply, biasing may be necessary when the sensor output can remain near ground. Decouple the supply pins locally and keep sensor returns away from high-current output paths to prevent common-mode errors and unstable feedback behavior.
Được đề xuất
Audio Preamplification
The LM324ADE4 can provide modest audio-band voltage gain when the source impedance and required bandwidth are compatible with its 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate. Four independent channels allow separate preamplifier, balance, or mix stages in one 14-SOIC package. Its general-purpose architecture favors straightforward line-level amplification rather than low-noise microphone work. Check the input-voltage and bias-current limits against the source, and use the manufacturer application information to choose suitable feedback and compensation arrangements. Keep audio return currents separate from digital and switching-node paths to minimize hum and channel crosstalk.
Được đề xuất
Industrial Control Loops
The four independent LM324ADE4 channels are useful in basic industrial control loops where error amplification, actuator drive, and signal comparison must fit in a compact package. The 1.2 MHz bandwidth is more than adequate for many slow feedback loops, while the 0.5 V/µs slew rate can drive moderate capacitive loads when stability is checked. Use separate channels for error, feedforward, and output-stage functions, with RC compensation added only where the closed-loop response requires it. Protect inputs against industrial transients and observe the output-current limit. A grounded guard around sensitive high-impedance nodes helps reduce leakage-induced offsets and noise pickup.
Được đề xuất
Buffering and Level Shifting
LM324ADE4 channels configured as unity-gain buffers are practical for impedance isolation between higher-impedance sensors and downstream measurement circuits. Internal frequency compensation removes the need for a separate compensation capacitor in the standard non-inverting buffer configuration. The device can operate from split supplies when the system provides bipolar signals, or from a single positive rail when downstream logic requires a referenced output. Verify that the input remains inside the common-mode range and that the output has sufficient swing. Place bypass capacitors at the package supply pins and route feedback traces away from power-converter nodes to preserve low-noise operation.
Được đề xuất
Threshold Detection and Relay Logic
The LM324ADE4 can compare a sensor or supply-derived voltage against a reference and produce a control signal for threshold-based system behavior. Its 1.2 MHz closed-loop bandwidth provides ample response time for slow monitoring functions, and four channels allow multiple comparisons without separate packages. Set the reference with a stable resistor divider or reference source and add hysteresis to prevent oscillation when noise crosses the threshold. Use an output driver stage when the load current exceeds the amplifier's capability. Confirm output-swing margins under the worst-case supply and load conditions before connecting the signal to a relay driver, counter, or MCU input.
Được đề xuất
Test and Measurement Front Ends
LM324ADE4 channels can form the input-conditioning front end of a general-purpose measurement instrument by buffering sources, amplifying differential voltages, and driving an ADC. The 1.2 MHz gain-bandwidth product accommodates slow instrumentation signals, while the 0.5 V/µs slew rate supports moderate settling requirements at reduced gain. Use grounded differential routing, short feedback paths, and careful source-impedance balancing to minimize offset and conversion error. Input protection must preserve the allowed common-mode range, and the chosen ADC should be sampled only after the amplifier output has settled. This arrangement favors general bench and panel equipment rather than precision or wide-band measurement front ends.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM324ADE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM324AD | LM324M | LM324KADG4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Amplifiers | 4 independent channels | 4 independent channels | 4 independent channels | 4 independent channels |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Slew Rate | 0.5 V/µs | 0.5 V/µs | 0.5 V/µs | 0.5 V/µs |
| Qualification and Temperature Grade | E4 qualification and temperature-grade suffix | AD qualification and temperature-grade suffix | M qualification and temperature-grade suffix | KADG4 qualification and temperature-grade suffix |
Bảo phân biệt quan trọng
- Four independent general-purpose channels in one package (vsLM324M)
- Matches the core LM324M bandwidth and slew rate (vsLM324M)
- Pin-compatible option for qualified family sourcing (vsLM324AD)
Ghi chú thiết kế
Place the supply-bypass capacitor and feedback components close to the relevant LM324ADE4 pins. Keep the input and feedback traces short, and route them away from switching-node copper and high-current return paths. For a high-impedance source, use a guarded or driven shield where practical because leakage and surface contamination can create errors larger than the intended signal. Confirm the 14-pin SOIC land pattern against the package drawing before release.
Do not treat the full supply-voltage range as the input common-mode or output-swing range. A 5 V single-supply circuit can still clip an output or violate the input range if the signal approaches a rail. Add biasing for ground-referenced, single-supply signals and include adequate output headroom. Also account for the LM324ADE4 input-bias current when designing with high-source-impedance sensors.
Internal frequency compensation supports standard unity-gain operation, but capacitive loading can still reduce stability or cause oscillation. Keep the output connection short, isolate long cable or probe capacitance, and add an isolation resistor when the load requires it. Verify closed-loop gain, phase margin, and output settling at the lowest intended supply voltage rather than relying only on nominal simulation conditions.
For split-supply circuits, connect the bypass network to the same quiet ground reference used by the signal source. Avoid creating large copper loops between input and output grounds, because those loops can couple motor, relay, or digital currents into the amplifier. Use a solid ground-plane strategy for the 14-SOIC footprint and keep the exposed routing area beneath the package free of unnecessary high-current paths.
Thông tin tuân thủ
No specific RoHS, REACH, halogen-free, or conflict-minerals declaration is identified in the manufacturer page listing. The E4 orderable suffix does not by itself establish automotive qualification.
