STMicroelectronics

LM358QT - Dual Op-Amp 1.1MHz DFN-8 | STMicroelectronics

MPN: LM358QT ✓ Hoạt động
100 dB Vdss 20 nA Id 8-UFDFN Exposed Pad (DFN 2x2 mm) Package Internally compensated Speed
MOQ: 1 |

LM358QT Tóm tắt

The STMicroelectronics LM358QT is a low-power dual operational amplifier integrating two independent, high-gain, internally frequency-compensated op-amp circuits in an 8-pin UFDFN exposed-pad package measuring 2x2 mm. It delivers a gain-bandwidth product of 1.1 MHz (temperature compensated), a slew rate of 0.6 V/us, and a large DC voltage gain of 100 dB, operating from a single supply of 3 V to 30 V or dual supplies of +/-1.5 V to +/-15 V.

An operational amplifier is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. As a member of the linear amplifier / signal conditioning IC family within analog semiconductor hierarchy, the general-purpose dual op-amp is one of the most widely used building blocks in electronics, performing amplification, active filtering, buffering, level shifting, and comparator-like threshold detection in virtually every analog signal chain.

Key differentiating features include internally frequency compensation (no external compensation components required), very low supply current per amplifier for battery-powered designs, low input bias current of 20 nA, and unity-gain stability across the full industrial temperature span. The wide 3 V to 30 V single-supply range allows direct operation from logic supplies or automotive rails through simple regulation.

Architecturally, the LM358QT consists of two independent, high-gain op amps sharing a common supply pin pair. The internally compensated bipolar design guarantees stability at unity gain without external capacitors, while the exposed-pad DFN-8 package provides a low thermal resistance path to the PCB, supporting compact, high-density layouts where SOIC-8 footprints are too large.

Typical applications include transducer amplifiers and sensor signal conditioning, DC gain blocks and active filters in industrial controls, and battery-powered consumer or portable instrumentation where quiescent drain matters. It also serves as a summing amplifier, integrator, or voltage follower in general-purpose analog front ends.

Design consideration: as a general-purpose bipolar-input op amp, the LM358QT is not a precision part; for microvolt-level offset or high-speed requirements, select a dedicated precision or high-bandwidth amplifier. Ensure the common-mode input range and output swing limitations near the rails are respected in single-supply designs.

This page consolidates verified datasheet parameters, drop-in alternatives, pricing context, and practical design notes not found in the manufacturer datasheet alone.

Bộ thay thế dễ dàng lắp đặt cho LM358QT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM358QT (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Slew Rate, Input Bias Current, Frequency Compensation.

STMicroelectronics
Amplifier Type: Low-power dual operational amplifier
Package: 8-DFN, 2 x 2 mm
Slew Rate: 0.6 V/µs
So sánh với LM358QT →
Diodes Incorporated
Amplifier Type: General Purpose
Package: 8-pin TSSOP
Slew Rate: 0.3 V/µs
So sánh với LM358QT →

LM258QT

✅ Drop-In ⚠️ Thông số chưa được xác minh
STMicroelectronics
📦 8-UFDFN Exposed Pad (2x2 mm)
Low-power dual operational amplifier · 2 independent amplifiers · 1.1 MHz · 100 dB · 85 dB · 0.6 V/µs · 2 mV · 20 nA

Liên hệ để biết giá

Xem tài liệu →

LM158QT

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-UFDFN Exposed Pad (2x2 mm)
military/extended temperature grade of the same ST dual op-amp family, identical electrical specs and pinout

📋 Tham chiếu thay thế (không có trong danh mục)

LM2904QTH-13

✅ Drop-In ⚠️ Thông số chưa được xác minh
Diodes Incorporated
📦 8-UFDFN Exposed Pad (2x2 mm)
General Purpose · 2 circuits · 2 amplifiers · 36 V · ±18 V · 700 kHz · 0.3 V/µs · 7 mV

Liên hệ để biết giá

Xem tài liệu →

LM358QT Tỷ lệ tối đa & tính chất điện

Amplifier Type General Purpose Operational Amplifier
Number of Circuits 2
Gain Bandwidth Product 1.1 MHz (temperature compensated)
Slew Rate 0.6 V/us
Large DC Voltage Gain 100 dB
Input Bias Current 20 nA
Supply Voltage Range (Single) 3 V to 30 V
Supply Voltage Range (Dual) +/-1.5 V to +/-15 V
Hộp 8-UFDFN Exposed Pad (DFN 2x2 mm)
Kiểu lắp đặt Surface Mount
Packaging Tape & Reel
Frequency Compensation Internally compensated
Trạng thái RoHS Compliant
Output Short-Circuit Protection Yes (per ST LM358 family datasheet)

Cấu hình chân LM358QT

QFN-8 (2x2mm, EP) Package Pinout Diagram QFN-8 2x2mm, P0.5mm, EP 0.7x1.3mm, JEDEC MO-229. Pin 1 by dot. 1 2 3 4 5 6 7 8 QFN-8 (2x2mm, EP)
Chân 1 OUT1 — Output of amplifier A
Chân 2 IN1- — Inverting input of amplifier A
Chân 3 IN1+ — Non-inverting input of amplifier A
Chân 4 GND/V- — Ground or negative supply
Chân 5 IN2+ — Non-inverting input of amplifier B
Chân 6 IN2- — Inverting input of amplifier B
Chân 7 OUT2 — Output of amplifier B
Chân 8 V+ — Positive supply

Ứng dụng tiêu biểu

LM358QT phù hợp cho 6 Áp dụngs: Transducer and Sensor Signal Conditioning, Industrial Control Analog Blocks, Battery-Powered Portable Instruments, Audio Preamplification and Active Filters, DC Summing, Integrator and Comparator-Adjacent Blocks, Voltage Reference Buffering and Level Shifting.

🔧

Transducer and Sensor Signal Conditioning

The LM358QT fits sensor front ends because its 20 nA input bias current barely loads high-impedance transducers, and its 100 dB DC gain provides large closed-loop gain in a single stage for bridge and photodiode signals. The 3 V to 30 V single-supply range lets one rail power both the sensor and the amplifier. In a typical topology the second amplifier channel handles gain while the first channel buffers or filters. Keep input common-mode above ground since the bipolar input stage does not sense exactly to the negative rail.

🏭

Industrial Control Analog Blocks

On 24 V industrial rails the LM358QT operates comfortably within its 30 V maximum single-supply rating, amplifying current-sense and setpoint signals without extra regulation. Its internally frequency-compensated topology guarantees unity-gain stability with no external components, simplifying DIRM/control-board design. The 2x2 mm UFDFN-8 exposed-pad package saves board area versus SOIC-8 in dense PLC I/O modules. Designers should verify power dissipation at high supply voltage and add the exposed-pad ground connection for reliable thermal performance in sealed industrial enclosures.

📱

Battery-Powered Portable Instruments

The LM358QT family's very low supply current per amplifier makes it a good fit for battery-operated multimeters, gas detectors, and handheld medical meters that run from a single 3 V to 9 V cell. The dual-channel integration means one package performs buffering plus gain, halving the channel count versus single op-amps. Because quiescent drain rises with supply voltage, running at the minimum practical V+ extends battery life. The 1.1 MHz bandwidth covers DC and audio-band measurement signals typical of portable instrumentation front ends.

🎧

Audio Preamplification and Active Filters

With a 1.1 MHz temperature-compensated bandwidth, 0.6 V/us slew rate, and 100 dB open-loop gain, the LM358QT supports microphone preamps, tone-control stages, and Sallen-Key active filters across the full audio band. Two independent channels enable stereo processing or filter-plus-buffer topologies in one 2x2 mm footprint. Its internally compensated bipolar design ensures click-free unity-gain stability. For low-noise, low-distortion stage design, respect the output swing limits near the rails and source impedance levels appropriate to a general-purpose bipolar-input amplifier.

⚡

DC Summing, Integrator and Comparator-Adjacent Blocks

The LM358QT's 100 dB large-signal DC gain supports precision summing amplifiers, integrators, and level-shift blocks in control loops and test fixtures. One channel can integrate a tachometer or error signal while the second channel scales and offsets it for an ADC or comparator. The exposed-pad UFDFN-8 package keeps thermal gradients low for offset stability. Design tip: use a bias-current compensation resistor on the non-inverting input to cancel input bias current error, and observe the common-mode range in single-supply integrator topologies.

🔌

Voltage Reference Buffering and Level Shifting

As a unity-gain-stable, internally compensated amplifier, the LM358QT buffers voltage references and DAC outputs for distribution to comparators and sensor excitation inputs, with one package supplying two independent buffered rails. Its 30 V single-supply ceiling allows buffering references close to higher analog rails. Output short-circuit protection adds robustness against accidental board shorts. Designers should note the general-purpose output stage's limited sink capability near the negative rail and add a resistive pull-down when the buffered load must operate close to ground.

What is the supply voltage range of LM358QT?
The LM358QT operates from a single supply of 3 V to 30 V, or from dual supplies of +/-1.5 V to +/-15 V. According to the STMicroelectronics LM358QT datasheet, this wide range allows the dual op-amp to run directly from a single lithium cell, a 5 V logic rail, or higher industrial and automotive voltage rails, provided the absolute maximum ratings and common-mode input range are respected in single-supply designs.
What is the gain bandwidth product of LM358QT?
The LM358QT has a gain-bandwidth product of 1.1 MHz, which STMicroelectronics specifies as temperature compensated, meaning unity-gain bandwidth stays close to 1.1 MHz across the operating temperature range. This makes the part suitable for audio-frequency amplification, low-speed sensor conditioning, and active filters up to roughly the tens-of-kilohertz range, but not for video or RF signal chains that require tens or hundreds of megahertz of bandwidth.
What is the difference between LM358QT and LM2904?
The LM358 and LM2904 are both low-power dual operational amplifiers with the same standard 8-pin dual op-amp pinout and very similar electrical characteristics. The main difference is the temperature grade and qualification target: the LM2904 family is specified and marketed for automotive and harsh industrial environments with a wider guaranteed temperature span, while the LM358 targets commercial and industrial use. Verify the exact temperature range and package options in each manufacturer datasheet before substituting in an automotive design.
Can LMV358 replace LM358QT?
Not as a direct drop-in in all designs. The LMV358 shares the dual op-amp pinout but is a low-voltage part specified for supplies typically up to about 5.5 V, whereas the LM358QT operates from 3 V to 30 V. If your circuit runs above roughly 5 V, the LMV358 would be over-stressed. For a low-voltage, battery-powered design under 5.5 V the LMV358 can functionally replace the LM358 with lower quiescent current; always confirm supply range, output swing, and bandwidth against your application before committing.
What is the best drop-in replacement for LM358QT?
For a pin-compatible replacement in the same 2x2 mm UFDFN-8 exposed-pad package, first consider other members of the STMicroelectronics LM358 family such as the LM258QT and LM158QT, which differ mainly in temperature grade, and the LM2904QT automotive-grade variant. All share the standard dual op-amp pinout (OUT1, IN1-, IN1+, GND, IN2+, IN2-, OUT2, V+) and nearly identical electrical specifications, so substitution requires only a temperature-grade check rather than a PCB respin.
What is the best automotive-grade equivalent for LM358QT?
The best automotive-oriented equivalent is the STMicroelectronics LM2904QT, an automotive-grade member of the same low-power dual op-amp family offered in the same UFDFN-8 exposed-pad package with the same pinout. STMicroelectronics positions the LM2904 line for automotive and industrial systems with extended temperature specifications. Cross-brand automotive options exist from other manufacturers, but any cross-brand substitution should be validated package-by-package and grade-by-grade against the current datasheets before release to production.
Where can I download the LM358QT datasheet PDF?
The LM358QT datasheet PDF is available from STMicroelectronics through the official ST product page and online store, and mirrored on datasheet aggregators such as AllDatasheet, where it is listed as a 25-page document describing the low-power dual operational amplifiers. For design work, always use the latest revision from the STMicroelectronics website, since older revisions may not reflect current ratings, package mechanical drawings, or ordering information for the QT (UFDFN-8) suffix.
What is the pinout of LM358QT in the DFN-8 package?
The LM358QT uses the industry-standard dual op-amp pinout in its 8-pin UFDFN exposed-pad package: pin 1 is OUT1 (output of amplifier A), pin 2 is IN1- (inverting input A), pin 3 is IN1+ (non-inverting input A), pin 4 is GND/V- (negative supply or ground), pin 5 is IN2+ (non-inverting input B), pin 6 is IN2- (inverting input B), pin 7 is OUT2 (output of amplifier B), and pin 8 is V+ (positive supply). The exposed pad is normally connected to ground for thermal dissipation.
Is LM358QT suitable for single-supply operation?
Yes, the LM358QT is specifically designed to operate from a single power supply over a wide voltage range of 3 V to 30 V. STMicroelectronics describes the circuits as two independent, high-gain, internally frequency-compensated op amps specifically designed for single-supply operation. Keep in mind the general-purpose bipolar input stage: the common-mode input range does not extend fully to the negative rail, so bias inputs slightly above ground in single-supply configurations to guarantee linear operation.
What are the key specifications of LM358QT that engineers should know?
The LM358QT is a dual general-purpose operational amplifier in an 8-pin UFDFN exposed-pad (2x2 mm) package from STMicroelectronics. Key specifications per the ST datasheet: gain-bandwidth product 1.1 MHz (temperature compensated), slew rate 0.6 V/us, large DC voltage gain 100 dB, input bias current 20 nA, supply range 3 V to 30 V single or +/-1.5 V to +/-15 V dual, internally frequency compensated for unity-gain stability, and Tape & Reel packaging. It suits audio, sensor conditioning, and general analog blocks.
How much current does the LM358QT consume?
The LM358 family is characterized by very low supply current per amplifier channel, which is one of its headline features for battery-powered designs; the exact typical and maximum figures in milliamperes per amplifier are specified in the STMicroelectronics LM358QT datasheet under supply current. Because both channels share one supply pin pair, total quiescent drain is roughly double the per-amplifier figure. Consult the datasheet electrical characteristics table for the value at your specific supply voltage, since consumption varies with V+.
What is the slew rate of LM358QT and why does it matter?
The LM358QT has a slew rate of 0.6 V/us. Slew rate defines the maximum rate of change of the output voltage and therefore limits large-signal bandwidth: a 0.6 V/us part reproducing a 10 V peak sine wave is slew-limited above roughly 20 kHz, even though its small-signal bandwidth is 1.1 MHz. For audio-range and DC-to-low-frequency applications this is adequate; for fast pulse or high-amplitude high-frequency signals, choose a higher slew-rate amplifier such as the THS series.
Is LM358QT in stock and how can I get a price?
The LM358QT is listed as an active STMicroelectronics part and distributor listings such as LCSC show it in stock. Current pricing for the LM358QT depends on quantity, packaging (Tape & Reel), and daily market conditions, so it is not printed as a static figure here. Use the Request a Quote form on this page to receive a real-time price, confirmed stock quantity, and lead time for the exact quantity you need, from unit samples through full production reels.
What is the lead time and MOQ for LM358QT?
The LM358QT is supplied in Tape & Reel packaging, and the standard reel quantity is defined in the STMicroelectronics ordering information section of the datasheet. Because the part is an active, high-volume general-purpose amplifier, factory lead time is generally short, but exact current lead time and minimum order quantity vary with distributor inventory and production allocation. Submit your required quantity through the Request a Quote form on this page and the quotation will include confirmed lead time, reel/cut-tape options, and MOQ.
When should I choose LM358QT over a modern CMOS op-amp?
Choose the LM358QT when you need a proven, ultra-low-cost general-purpose dual op-amp with a wide 3 V to 30 V supply range and guaranteed unity-gain stability in a very small 2x2 mm package. A modern CMOS or precision amplifier is the better choice when you need picoamp-level bias current, rail-to-rail input/output swing, microvolt offset, or higher bandwidth. The LM358QT wins on cost maturity, supply ruggedness, and availability; precision CMOS parts win on DC accuracy and low-voltage headroom.

Dữ liệu tham khảo kỹ thuật cho LM358QT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the LM358QT when you need a proven, low-cost dual general-purpose op-amp in a very small 2x2 mm UFDFN-8 exposed-pad package, operating from a single 3 V to 30 V rail with guaranteed unity-gain stability. Choose the LM258QT or LM158QT from the same ST family when your design must operate over extended or military temperature ranges, since they share the identical footprint and electricals. Choose the LM2904QT for automotive or harsh-industrial qualification requirements. Avoid the LM358QT when your application needs rail-to-rail input/output swing, sub-microvolt offset, picoamp bias current, or bandwidth beyond 1.1 MHz; in those cases select a precision CMOS or high-speed amplifier instead. The main trade-off is DC precision versus cost maturity and supply ruggedness.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM258QT LM158QT LM2904QT
Package 8-UFDFN Exposed Pad (2x2 mm) 8-UFDFN Exposed Pad (2x2 mm) - same 8-UFDFN Exposed Pad (2x2 mm) - same 8-UFDFN Exposed Pad (2x2 mm) - same
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Number of Circuits 2 2 2 2
Gain Bandwidth Product 1.1 MHz 1.1 MHz 1.1 MHz 1.1 MHz
Slew Rate 0.6 V/us 0.6 V/us 0.6 V/us 0.6 V/us
Large DC Voltage Gain 100 dB 100 dB 100 dB 100 dB
Single Supply Range 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 26 V (per family datasheet)

Bảo phân biệt quan trọng

  • Compact 2x2 mm UFDFN-8 exposed-pad footprint (vsLM258QT)
  • Extended and automotive temperature grade options in the same footprint (vsLM2904QT)
  • Wide 30 V single-supply tolerance (vsLMV358-class low-voltage parts)

Ghi chú thiết kế

Connect the UFDFN-8 exposed pad to the ground plane with an array of thermal vias. The exposed pad is the primary thermal and, for signal integrity, the local 0 V reference for the bipolar input stage. Because the 2x2 mm DFN land pattern has minimal perimeter, follow the STMicroelectronics recommended footprint in the datasheet mechanical drawing exactly; DFN solder wicking defects are the most common assembly issue with this package.

Decouple V+ (pin 8) with a 100 nF ceramic capacitor placed within 2 mm of the pin, plus a bulk 1 uF to 10 uF capacitor per rail segment. At 30 V supply with both channels driving moderate loads, verify total device dissipation against the exposed-pad theta_JA before finalizing copper area. Estimated: with a few mA per channel at 30 V, dissipation stays under a few tens of milliwatts, but high-load applications should recheck against the datasheet thermal table.

The LM358 input common-mode range does not include the negative rail: on a single 3.3 V or 5 V supply, keep input signals at least a few hundred millivolts above ground or the output will clip unexpectedly. Similarly the general-purpose output stage cannot swing to V+ under load. Many 'LM358 not working at unity gain near zero' field issues come from violating these two range limits, not from a defective part.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Yes
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS compliance indicated on distributor listings for the ST LM358QT. Automotive-grade designs should use the LM2904 family instead.

Dữ liệu được xác minh vào: 2026-11-08 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM358QT datasheet LM358QT datasheet pdf LM358QT pinout STMicroelectronics LM358QT LM358QT equivalent LM358QT replacement LM358QT vs LM2904 LM358QT price LM358QT stock LM358 DFN-8 dual op-amp low power dual operational amplifier 1.1MHz LM358 sensor signal conditioning circuit

Các bộ phận và thuật ngữ liên quan

STMicroelectronics LM358QT LM258QT LM158QT LM2904QT LMV358 operational amplifier op-amp dual amplifier linear amplifier IC gain-bandwidth product slew rate input bias current UFDFN-8 DFN package exposed pad surface mount RoHS single-supply operation Tape & Reel sensor signal conditioning active filter audio preamplifier
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ