LPC1810FET100 - 180MHz Cortex-M3 MCU in TFBGA100 | NXP
MPN: LPC1810FET100 ✓ Hoạt độngLPC1810FET100 Tóm tắt
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and communication interfaces into one package. The Cortex-M3 belongs to the Arm Cortex-M family of compact embedded processors, while the LPC1810 belongs to NXP's LPC18xx industrial microcontroller portfolio. This hierarchy places the device among flashless 32-bit MCUs intended for control, communications, and data-acquisition systems.
The LPC1810FET100 combines a 150 MHz distributor-listed operating rating with an NXP product-page maximum of up to 180 MHz. Its 136 kB SRAM provides working memory for protocols, control loops, and buffered data. Peripheral integration includes CAN 2.0B for networked industrial equipment, a Quad SPI Flash Interface for external code and data storage, and a State Configurable Timer for flexible event timing or waveform generation.
As a ROMless device, the LPC1810FET100 is intended to boot from external nonvolatile memory. The Quad SPI Flash Interface provides a dedicated path for code and configuration storage while the Cortex-M3 performs real-time processing. CAN support makes the device relevant to industrial controllers, motor-control equipment, instrumentation, and service-bus nodes where robust field-bus communication is required.
Typical designs include industrial automation controllers, CAN-connected sensor gateways, embedded data-acquisition units, communications equipment, and compact control systems. External memory capacity and the selected firmware image determine how much application code and data can be stored. Engineers should also account for BGA assembly requirements, power-management design, clock configuration, and peripheral pin multiplexing.
A key implementation consideration is the 9 x 9 mm TFBGA100 footprint. The board must provide all 100 balls, including power, ground, signal, and exposed thermal connections defined by the package drawing. Follow NXP's pin-connection and board-layout guidance to preserve signal integrity, provide clean supply rails, and maintain thermal performance during operation.
This product page combines NXP device information, distributor package identification, strict same-package replacement analysis, and practical integration considerations. It also distinguishes a genuine PCB drop-in replacement from merely similar Cortex-M3 devices, helping engineers make sourcing and design decisions without assuming that equal memory size, package dimensions, or processor architecture guarantees pin compatibility.
Bộ thay thế dễ dàng lắp đặt cho LPC1810FET100 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LPC1810FET100 (cùng hình factor và footprint) — khác nhau ở Package.
LPC1811FET100
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LPC1812FET100
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LPC1813JET100E
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LPC1814FET100
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LPC1815FET100
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LPC1810FET100 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Processor Core | Arm Cortex-M3 |
| Maximum Operating Frequency | Up to 180 MHz |
| Distributor-Listed Operating Frequency | 150 MHz |
| Internal SRAM | 136 kB |
| Program Memory | ROMless; external nonvolatile memory required |
| CAN Support | CAN 2.0B |
| External Memory Interface | Quad SPI Flash Interface |
| Timer Feature | State Configurable Timer |
| Architecture | 32-bit |
| Hộp | 100-TFBGA, 9 x 9 mm |
| Kiểu lắp đặt | Surface mount |
| Pin/Ball Count | 100 balls |
Hướng dẫn cấu hình chân LPC1810FET100 100-tfbga, 9 x 9 mm
Cấu hình chân cho LPC1810FET100 (100-tfbga, 9 x 9 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho LPC1810FET100.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LPC1810FET100 phù hợp cho 6 Áp dụngs: CAN-Connected Industrial Controller, Industrial Sensor Gateway, External-SPI-Flash Data Logger, Compact Data-Acquisition Unit, Communications Equipment, Automotive or Robotics Control Module.
CAN-Connected Industrial Controller
The LPC1810FET100 fits industrial control nodes that require deterministic field-bus communication without adding a separate CAN controller. Its Cortex-M3 core operates at up to 180 MHz according to NXP, while CAN 2.0B handles bus framing and the 136 kB SRAM supports protocol state, control variables, and diagnostics. The MCU is placed beside a suitable CAN transceiver, with the transceiver's logic reference and bus-side isolation or surge protection handled separately. Because the LPC1810FET100 is ROMless, firmware can reside in external SPI flash reached through the dedicated Quad SPI Flash Interface. Designers should size the external memory for the boot image, update workspace, and application data. The main performance benefit is integrated CAN and high-speed control in one 9 x 9 mm TFBGA device, although regulator headroom, transceiver standby behavior, and bus timing margins must be verified.
Được đề xuất
Industrial Sensor Gateway
The LPC1810FET100 is suitable for a compact gateway that aggregates readings from local sensors, runs filtering and protocol conversion, and forwards status over CAN. Its 136 kB of internal SRAM provides working space for sampling buffers, calibration tables, message queues, and network stacks, while the 180 MHz maximum Cortex-M3 speed allows useful processing headroom. A serial or SPI sensor can share the external bus architecture with the Quad SPI Flash Interface, provided the selected peripheral instances and pins do not conflict. Use external SPI flash for boot firmware, configuration data, and buffered records. The benefit is integration of high-speed control, SRAM, and CAN in one package, reducing the component count for compact industrial equipment. Engineering checks include sensor timing, interrupt priority, watchdog strategy, thermal performance, and the operating limits of the selected power rails.
Được đề xuất
External-SPI-Flash Data Logger
A ROMless implementation fits the LPC1810FET100 particularly well in a data logger that stores events in external serial flash. The dedicated Quad SPI Flash Interface provides a defined path for code and nonvolatile data, while the 136 kB SRAM can buffer measurements before the controller writes them to storage. At operating speeds up to 180 MHz, the Cortex-M3 can handle timestamps, filtering, compression, and communication tasks concurrently. Separate logic devices should be connected according to the datasheet's multiplexing rules so the flash interface remains available. The design advantage is the combination of external memory support and substantial internal SRAM without reserving internal program flash. Practical considerations include flash endurance, write wear leveling, brownout-safe update procedures, boot recovery, and ensuring that the storage device and power supply remain within their specified limits.
Được đề xuất
Compact Data-Acquisition Unit
The LPC1810FET100 can serve as the control core of a compact data-acquisition unit that buffers sensor data, applies calibration, and transfers results over a communications network. Its 136 kB of SRAM supports sample buffers and protocol handling, and the Cortex-M3 architecture provides substantially more processing capability than a simple state-machine controller. The State Configurable Timer can assist with periodic sampling or event timing when its configured outputs are assigned to the required pins. The ROMless configuration permits the program image and calibration records to be maintained in external SPI flash, enabling controlled firmware revisions. CAN 2.0B is useful where the acquisition unit participates in an industrial network, though a physical transceiver is still required. The principal design trade-off is board complexity from external memory and a 100-ball BGA, balanced against compact packaging and integrated real-time processing.
Được đề xuất
Communications Equipment
The LPC1810FET100 fits communications equipment that requires local protocol processing and deterministic control alongside a CAN management interface. Its maximum operating frequency of 180 MHz and 136 kB of SRAM allow buffering and frame processing, while CAN 2.0B handles network management, diagnostics, or a lower-speed industrial side channel. The Quad SPI Flash Interface supports external boot code and configuration data, useful in network appliances with remotely managed firmware. Designers can implement the high-speed data path through other LPC18xx peripherals subject to the exact device pin and peripheral configuration, so the final signal assignment must come from the datasheet. The integrated MCU reduces the need for separate logic but requires careful grounding between communication circuitry, external memory, and the 100-TFBGA device. Watchdog handling, EMC design, firmware rollback, and connector surge protection remain important implementation concerns.
Được đề xuất
Automotive or Robotics Control Module
The LPC1810FET100 is a candidate for compact robotics or automotive-adjacent control modules that need CAN communications and deterministic real-time behavior. The Cortex-M3 core operates at up to 180 MHz according to NXP, and the 136 kB SRAM supports motion-state calculations, diagnostics, and communication buffering. CAN 2.0B connects the controller to a vehicle or robot network through an external transceiver, while the ROMless architecture allows firmware to be stored in external SPI flash. This arrangement can support field updates, but update integrity, boot fallback, and brownout handling must be designed explicitly. Qualification for an automotive environment cannot be inferred from the product family alone; temperature range, AEC-Q100 status, transient immunity, and functional-safety requirements require separate confirmation. For robotics, the same part may be suitable where size and CAN integration matter more than internal program flash.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LPC1810FET100 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LPC1811FET100 | LPC1812FET100 | LPC1813JET100E | LPC1814FET100 | LPC1815FET100 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) | 100-TFBGA (9 x 9 mm) |
| Processor Core | Arm Cortex-M3 | Arm Cortex-M3 | Arm Cortex-M3 | Arm Cortex-M3 | Arm Cortex-M3 | Arm Cortex-M3 |
Bảo phân biệt quan trọng
- ROMless architecture with a dedicated Quad SPI Flash Interface (vsLPC1813JET100E)
- 136 kB of internal SRAM (vsLPC1813JET100E)
- Up to 180 MHz operating speed with CAN 2.0B integration (vsLPC1813JET100E)
- Compact 9 x 9 mm TFBGA100 implementation (vsLPC1811FET100)
Ghi chú thiết kế
Use the manufacturer's 100-TFBGA land pattern and exact ball map rather than deriving a footprint from the 9 x 9 mm body size alone. Place external SPI flash, decoupling, and any CAN transceiver or interface circuitry according to the recommended layout, keeping high-current and high-speed paths away from sensitive inputs. Verify assembly clearances, solder-mask design, and via-in-pad requirements with the board manufacturer.
Decouple each supply pin with the capacitance and placement specified in the NXP datasheet, and confirm the regulator can meet both startup and peak current requirements at the intended clock. Because operating current varies with clock activity, SRAM use, peripherals, and temperature, evaluate the worst-case load rather than relying on a nominal figure. Also account for voltage tolerance, sequencing, and brownout behavior for a ROMless boot design.
Do not treat a shared TFBGA package as proof that every LPC18xx member is automatically interchangeable. Compare ball-level signals, boot configuration, supply pins, peripheral multiplexing, embedded versus external program memory, and software startup support. For the LPC1810FET100, make the external flash capacity, boot-image format, firmware update method, and recovery path part of the hardware validation plan.
Estimate junction temperature from actual dissipation and the package's specified thermal characteristics before selecting copper area or cooling. Estimated: the temperature rise equals power dissipation multiplied by the applicable junction-to-ambient thermal resistance; obtain both values from the datasheet for the exact package and PCB construction. Validate with a worst-case ambient temperature, continuous processor load, and the external flash operating simultaneously.
Route high-speed external-memory signals as short, impedance-controlled connections on a multilayer board, with a continuous reference plane and appropriately placed series termination if recommended. Keep clock and data traces away from switching nodes and noisy regulators. Since the LPC1810FET100 is ROMless, boot quality depends on the complete path from external SPI flash through the MCU, making signal integrity and power sequencing part of system reliability.
Thông tin tuân thủ
The product listing does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm each declaration using the current NXP product documentation and applicable quality documentation before qualification.