LT1078IS8 - Micropower Dual Precision Op Amp | Analog Devices
MPN: LT1078IS8 ✓ Hoạt độngLT1078IS8 Tóm tắt
An operational amplifier is a high-gain, low-impedance differential amplifier used to amplify small signals. The micropower subset trades bandwidth and drive capability for lower supply consumption, making it appropriate for portable instrumentation, low-power sensor interfaces, and battery-operated measurement systems. In the broader IC hierarchy, the LT1078IS8 is an amplifier IC, an analog integrated circuit, and a semiconductor designed around precision feedback and common-mode rejection.
The LT1078IS8 uses two amplifier sections in one 8-pin package, allowing compact designs that need two signal-processing channels. Its 5 V single-supply optimization is important for systems powered from a regulated 5 V rail. The 600 uV maximum input offset voltage supports accurate DC amplification, while the 200 kHz gain-bandwidth figure provides useful bandwidth for low-frequency measurement and control paths. The bipolar process supports conventional op-amp input characteristics but requires attention to supply voltage and common-mode input limits.
The 8-SO package offers a small footprint for surface-mount assembly while retaining separate inputs and outputs for both channels. Pin assignments and electrical limits should be taken directly from the Analog Devices LT1078 datasheet and the specific ordering code LT1078IS8. The I suffix identifies an industrial-grade ordering option within the LT1078 family, while the S8 portion identifies the 8-pin surface-mount configuration. Exact temperature ratings, supply limits, bias currents, and common-mode ranges require confirmation from the manufacturer documentation.
Typical uses include low-level sensor conditioning, precision current measurement, portable test equipment, low-voltage audio and control circuits, and general-purpose battery-powered analog systems. Two integrated amplifier sections can implement independent gain stages, buffers, or differential signal paths. When the two amplifiers operate in related channels, their electrical behavior and layout should be evaluated to minimize offset and temperature-gradient effects.
The principal design consideration is the balance between low power and signal bandwidth. The approximately 200 kHz gain-bandwidth specification is adequate for many precision low-frequency tasks but may constrain higher closed-loop gain or faster transient requirements. Decoupling, input bias-current return paths, output loading, and common-mode range should all be checked against the operating rail. Feedback resistors should also be selected with values that do not demand excessive output current.
This product record combines the manufacturer’s device description, family-level application context, package identification, and drop-in considerations in one engineering-focused view. It also distinguishes the verified LT1078IS8 ordering code from related lead-free and packaging designations, helping designers evaluate PCB reuse without confusing ordering suffixes with functional differences.
Bộ thay thế dễ dàng lắp đặt cho LT1078IS8 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
LT1078IS8#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT1078S8#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LT1078IS8 Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Circuits | 2 circuits |
| Device Type | Micropower precision operational amplifier |
| Technology | Bipolar |
| Input Offset Voltage | 600 uV maximum |
| Gain-Bandwidth Product | 200 kHz |
| Optimized Supply Voltage | 5 V |
| Hộp | 8-SO small-outline surface-mount package |
| Số lượng chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân LT1078IS8 8-so small-outline surface-mount package
Cấu hình chân cho LT1078IS8 (8-so small-outline surface-mount package gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LT1078IS8.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LT1078IS8 phù hợp cho 6 Áp dụngs: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Precision Current Measurement, Low-Voltage Control Loops, Low-Power Audio Buffering, Two-Channel Data Acquisition.
Portable Sensor Signal Conditioning
The LT1078IS8 fits portable sensor front ends because it combines two precision amplifier channels with micropower operation and a 5 V single-supply design point. One channel can buffer a high-impedance sensor while the second provides configurable gain, active filtering, or a difference stage. Its 600 uV maximum input offset voltage helps preserve DC accuracy, although total error also depends on bias current, noise, and sensor resistance. The approximately 200 kHz gain-bandwidth product is appropriate for slow sensor signals rather than wideband measurement. Keep input traces short, use a bias-current return path, and verify that the sensor’s common-mode voltage remains within the amplifier’s allowed input range at the selected 5 V rail.
Được đề xuất
Battery-Powered Instrumentation
Battery-operated instrumentation benefits from the LT1078IS8’s micropower dual-channel architecture and single-supply operation at 5 V. Two independent amplifier sections can implement measurement amplification, buffering, or gain stages while limiting the number of analog ICs on the board. The 600 uV maximum offset voltage is useful for low-level DC signals, while the 200 kHz gain-bandwidth product supports conventional low-frequency control and measurement paths. Designers should still evaluate total supply demand, output swing, load current, and the regulator’s quiescent current. A local bypass capacitor and careful grounding are especially important when the amplifier shares a small 5 V rail with analog and digital circuitry.
Được đề xuất
Precision Current Measurement
The LT1078IS8 can amplify the small voltage produced by a shunt or current-sense element in a precision measurement circuit. Its bipolar dual-amplifier construction, 600 uV maximum offset specification, and two amplifier channels allow one section to amplify the sense voltage while the other can provide buffering, gain, or active filtering. The 5 V single-supply optimization fits many industrial and laboratory systems. Accuracy depends on keeping the sense voltage within the common-mode range, selecting feedback resistors that do not overload the output, and accounting for offset and bias-current error over temperature. The 200 kHz gain-bandwidth product should be checked against the required closed-loop gain and transient response.
Được đề xuất
Low-Voltage Control Loops
The LT1078IS8 is applicable to compact 5 V control systems requiring two low-power precision amplifier channels. The dual configuration can implement an error amplifier and feedback buffer, an active filter plus monitor, or two channels of a proportional control path. The 600 uV maximum offset voltage helps maintain accurate DC feedback, and the approximately 200 kHz gain-bandwidth product gives useful loop bandwidth for many slow industrial and embedded-control systems. Stability must be checked for the actual feedback network and capacitive loads, while output-current and voltage-headroom requirements should be compared with the commanded range. Shield sensitive input routing from switching nodes and keep analog return currents away from high-current output paths.
Được đề xuất
Low-Power Audio Buffering
The LT1078IS8 can provide low-level audio buffering and gain in compact 5 V systems. Its two amplifier sections permit separate handling of left and right channels or use as buffer and gain stages, while the micropower classification supports reduced supply demand. The 600 uV maximum offset voltage and 200 kHz gain-bandwidth product are adequate for many low-frequency audio paths, though the application must avoid operating near gain-bandwidth limits or outside the output swing. Input impedance, noise, and bias-current requirements should be checked against the source impedance. Decouple the supply rail near the device and maintain a clean analog ground reference to reduce channel-to-channel interaction and switching-noise coupling.
Được đề xuất
Two-Channel Data Acquisition
The LT1078IS8 supports compact two-channel data-acquisition front ends where each amplifier handles a separate sensor or differential input stage. Micropower behavior is valuable in distributed or handheld measurement systems, and the 600 uV maximum offset specification supports low-level signal amplification. The dual 8-SO implementation reduces component count while preserving independent channel routing. For accurate results, confirm the common-mode range at the actual 5 V supply, use matched resistor networks where channel correlation matters, and ensure the source impedance remains suitable for the input bias current. The 200 kHz gain-bandwidth product limits high-gain or fast-transient use, so designs requiring wider bandwidth should select a different amplifier family.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LT1078IS8 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LT1078IS8#PBF | LT1078S8#PBF |
|---|---|---|---|
| Package | 8-SO | 8-SO | 8-SO |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Number of Amplifier Circuits | 2 circuits | 2 circuits | 2 circuits |
| Optimized Supply Voltage | 5 V | 5 V | 5 V |
| Device Category | Micropower precision operational amplifier | Micropower dual precision operational amplifier | Micropower dual precision operational amplifier |
| Mounting Type | Surface mount | Surface mount | Surface mount |
| Ordering Designation | LT1078IS8 | LT1078IS8#PBF lead-free designation | LT1078S8#PBF S-grade designation |
Bảo phân biệt quan trọng
- Two precision amplifier channels in one compact package (vsLT1078S8#PBF)
- Optimized for compact 5 V single-supply systems (vsLT1078IS8#PBF)
- Precision offset suitable for low-level DC conditioning (vsLT1078IS8#PBF)
Ghi chú thiết kế
Treat the LT1078IS8 as a micropower device but calculate the complete analog-supply budget from the manufacturer’s specified channel and quiescent-current conditions. A single 5 V rail is the intended operating point, yet regulator efficiency, dropout margin, and the load drawn by the external feedback network also affect battery life. Place a local bypass capacitor at the supply pins and route its return directly to the device ground to prevent supply ripple from appearing as amplified input noise.
Use the manufacturer’s 8-SO pin-configuration drawing for every PCB layout and verify pin 1 orientation against the board footprint. Keep the two amplifier channels’ input and feedback paths short, separate from switching nodes and high-current returns. If both channels process correlated signals, use symmetric routing and resistor networks to minimize thermal gradients and channel mismatch. Confirm exposed-pad or thermal requirements against the specific package drawing before release.
Do not treat the 200 kHz gain-bandwidth figure as an unconditional operating frequency at every closed-loop gain. Check the resulting closed-loop bandwidth, output swing, capacitive-load stability, and common-mode range using the manufacturer datasheet. Also verify the input-source impedance against bias-current error and provide a suitable reference path for bipolar-input bias current. These checks are particularly important when the source is a resistive sensor with a long PCB connection.
Thông tin tuân thủ
Compliance attributes were not stated in the retrieved product snippets. The LT1078IS8#PBF ordering code contains a lead-free designation, but that ordering suffix alone was not used to assign the separate lead-free and halogen-free fields. AEC-Q100 qualification is not applicable to this general-purpose operational amplifier.