Analog Devices

LT1078IS8 - Micropower Dual Precision Op Amp | Analog Devices

料号: LT1078IS8 ✓ 量产中
600 uV maximum Vdss 8-SO small-outline surface-mount package Package
最小起订量: 1 |

LT1078IS8 概述

Analog Devices LT1078IS8 is a micropower dual operational amplifier optimized for single-supply operation at 5 V and offered in an 8-pin small-outline surface-mount package. The device provides two amplifier circuits, bipolar construction, a maximum offset voltage of 600 uV, and approximately 200 kHz gain-bandwidth performance. These characteristics place the LT1078IS8 in the precision operational-amplifier category for low-power analog signal conditioning.

An operational amplifier is a high-gain, low-impedance differential amplifier used to amplify small signals. The micropower subset trades bandwidth and drive capability for lower supply consumption, making it appropriate for portable instrumentation, low-power sensor interfaces, and battery-operated measurement systems. In the broader IC hierarchy, the LT1078IS8 is an amplifier IC, an analog integrated circuit, and a semiconductor designed around precision feedback and common-mode rejection.

The LT1078IS8 uses two amplifier sections in one 8-pin package, allowing compact designs that need two signal-processing channels. Its 5 V single-supply optimization is important for systems powered from a regulated 5 V rail. The 600 uV maximum input offset voltage supports accurate DC amplification, while the 200 kHz gain-bandwidth figure provides useful bandwidth for low-frequency measurement and control paths. The bipolar process supports conventional op-amp input characteristics but requires attention to supply voltage and common-mode input limits.

The 8-SO package offers a small footprint for surface-mount assembly while retaining separate inputs and outputs for both channels. Pin assignments and electrical limits should be taken directly from the Analog Devices LT1078 datasheet and the specific ordering code LT1078IS8. The I suffix identifies an industrial-grade ordering option within the LT1078 family, while the S8 portion identifies the 8-pin surface-mount configuration. Exact temperature ratings, supply limits, bias currents, and common-mode ranges require confirmation from the manufacturer documentation.

Typical uses include low-level sensor conditioning, precision current measurement, portable test equipment, low-voltage audio and control circuits, and general-purpose battery-powered analog systems. Two integrated amplifier sections can implement independent gain stages, buffers, or differential signal paths. When the two amplifiers operate in related channels, their electrical behavior and layout should be evaluated to minimize offset and temperature-gradient effects.

The principal design consideration is the balance between low power and signal bandwidth. The approximately 200 kHz gain-bandwidth specification is adequate for many precision low-frequency tasks but may constrain higher closed-loop gain or faster transient requirements. Decoupling, input bias-current return paths, output loading, and common-mode range should all be checked against the operating rail. Feedback resistors should also be selected with values that do not demand excessive output current.

This product record combines the manufacturer’s device description, family-level application context, package identification, and drop-in considerations in one engineering-focused view. It also distinguishes the verified LT1078IS8 ordering code from related lead-free and packaging designations, helping designers evaluate PCB reuse without confusing ordering suffixes with functional differences.

直接替换替代料: LT1078IS8 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

LT1078IS8#PBF

✅ 直接替换
📦 8-SO
Same LT1078 dual-amplifier family and 8-SO package; ordering designation adds the lead-free finish marker while maintaining 2 circuits and 600 uV maximum offset

📋 参考替代料(不在目录中)

LT1078S8#PBF

✅ 直接替换
📦 8-SO
Same LT1078 dual-amplifier family and 8-SO package; S-grade ordering differs from the I-grade target by 0 uV in maximum offset while temperature grade must be confirmed

📋 参考替代料(不在目录中)

LT1078IS8 最大额定值与电气特性

Number of Amplifier Circuits 2 circuits
Device Type Micropower precision operational amplifier
Technology Bipolar
Input Offset Voltage 600 uV maximum
Gain-Bandwidth Product 200 kHz
Optimized Supply Voltage 5 V
封装 8-SO small-outline surface-mount package
引脚数 8 pins
安装类型 Surface mount
AEC-Q100 Qualification Not applicable

LT1078IS8 8-so small-outline surface-mount package 引脚配置指南

LT1078IS8(8-so small-outline surface-mount package 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

LT1078IS8 的 8-so small-outline surface-mount package 封装引脚图

暂无详细引脚数据: LT1078IS8.

请参阅 数据手册 以查看完整引脚配置。

典型应用

LT1078IS8 适用于 6 应用s: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Precision Current Measurement, Low-Voltage Control Loops, Low-Power Audio Buffering, Two-Channel Data Acquisition.

📱

Portable Sensor Signal Conditioning

The LT1078IS8 fits portable sensor front ends because it combines two precision amplifier channels with micropower operation and a 5 V single-supply design point. One channel can buffer a high-impedance sensor while the second provides configurable gain, active filtering, or a difference stage. Its 600 uV maximum input offset voltage helps preserve DC accuracy, although total error also depends on bias current, noise, and sensor resistance. The approximately 200 kHz gain-bandwidth product is appropriate for slow sensor signals rather than wideband measurement. Keep input traces short, use a bias-current return path, and verify that the sensor’s common-mode voltage remains within the amplifier’s allowed input range at the selected 5 V rail.

🔋

Battery-Powered Instrumentation

Battery-operated instrumentation benefits from the LT1078IS8’s micropower dual-channel architecture and single-supply operation at 5 V. Two independent amplifier sections can implement measurement amplification, buffering, or gain stages while limiting the number of analog ICs on the board. The 600 uV maximum offset voltage is useful for low-level DC signals, while the 200 kHz gain-bandwidth product supports conventional low-frequency control and measurement paths. Designers should still evaluate total supply demand, output swing, load current, and the regulator’s quiescent current. A local bypass capacitor and careful grounding are especially important when the amplifier shares a small 5 V rail with analog and digital circuitry.

⚡

Precision Current Measurement

The LT1078IS8 can amplify the small voltage produced by a shunt or current-sense element in a precision measurement circuit. Its bipolar dual-amplifier construction, 600 uV maximum offset specification, and two amplifier channels allow one section to amplify the sense voltage while the other can provide buffering, gain, or active filtering. The 5 V single-supply optimization fits many industrial and laboratory systems. Accuracy depends on keeping the sense voltage within the common-mode range, selecting feedback resistors that do not overload the output, and accounting for offset and bias-current error over temperature. The 200 kHz gain-bandwidth product should be checked against the required closed-loop gain and transient response.

🏭

Low-Voltage Control Loops

The LT1078IS8 is applicable to compact 5 V control systems requiring two low-power precision amplifier channels. The dual configuration can implement an error amplifier and feedback buffer, an active filter plus monitor, or two channels of a proportional control path. The 600 uV maximum offset voltage helps maintain accurate DC feedback, and the approximately 200 kHz gain-bandwidth product gives useful loop bandwidth for many slow industrial and embedded-control systems. Stability must be checked for the actual feedback network and capacitive loads, while output-current and voltage-headroom requirements should be compared with the commanded range. Shield sensitive input routing from switching nodes and keep analog return currents away from high-current output paths.

🎧

Low-Power Audio Buffering

The LT1078IS8 can provide low-level audio buffering and gain in compact 5 V systems. Its two amplifier sections permit separate handling of left and right channels or use as buffer and gain stages, while the micropower classification supports reduced supply demand. The 600 uV maximum offset voltage and 200 kHz gain-bandwidth product are adequate for many low-frequency audio paths, though the application must avoid operating near gain-bandwidth limits or outside the output swing. Input impedance, noise, and bias-current requirements should be checked against the source impedance. Decouple the supply rail near the device and maintain a clean analog ground reference to reduce channel-to-channel interaction and switching-noise coupling.

🖥️

Two-Channel Data Acquisition

The LT1078IS8 supports compact two-channel data-acquisition front ends where each amplifier handles a separate sensor or differential input stage. Micropower behavior is valuable in distributed or handheld measurement systems, and the 600 uV maximum offset specification supports low-level signal amplification. The dual 8-SO implementation reduces component count while preserving independent channel routing. For accurate results, confirm the common-mode range at the actual 5 V supply, use matched resistor networks where channel correlation matters, and ensure the source impedance remains suitable for the input bias current. The 200 kHz gain-bandwidth product limits high-gain or fast-transient use, so designs requiring wider bandwidth should select a different amplifier family.

推荐产品汇总

LT1078IS8#PBF Same-family dual-amplifier option 用于: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Precision Current Measurement, Low-Voltage Control Loops, Low-Power Audio Buffering, Two-Channel Data Acquisition LT1078S8#PBF Same-package family option 用于: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Precision Current Measurement, Low-Voltage Control Loops, Low-Power Audio Buffering, Two-Channel Data Acquisition
What is the LT1078IS8?
The LT1078IS8 is an Analog Devices micropower dual precision operational amplifier in an 8-SO surface-mount package. According to the Analog Devices product page, the LT1078 family is optimized for single-supply operation at 5 V. The device contains two amplifier circuits, uses bipolar construction, and provides approximately 200 kHz gain-bandwidth performance, making it suitable for compact low-power analog signal-conditioning circuits.
What are the key specifications of LT1078IS8 that engineers should know?
The LT1078IS8 provides two amplifier circuits in an 8-pin small-outline surface-mount package, with a maximum input offset voltage of 600 uV and approximately 200 kHz gain-bandwidth performance. Analog Devices identifies the family as micropower and optimized for 5 V single-supply operation. The bipolar implementation supports precision general-purpose amplification, while the dual configuration saves board area compared with two separate single amplifier packages.
What is the operating voltage of LT1078IS8?
The LT1078IS8 is optimized for operation from a single 5 V supply. The Analog Devices product page specifically describes the LT1078 family as optimized for single-supply operation at 5 V. The exact minimum and maximum allowable supply voltages must be taken from the manufacturer datasheet before designing the circuit, because the optimization point does not by itself define the complete electrical limits.
Where can I download the LT1078IS8 datasheet PDF?
The official LT1078 datasheet and product information are available through the Analog Devices LT1078 product page at https://www.analog.com/en/products/lt1078.html. Use the manufacturer’s ordering information to confirm the LT1078IS8 grade, 8-SO package, and electrical limits. The datasheet is the authoritative source for the complete pin description, recommended operating conditions, and supply-current characteristics.
Where is the LT1078IS8 pinout located?
The LT1078IS8 pinout is documented in the pin-configuration section of the Analog Devices LT1078 datasheet. The part is an 8-pin surface-mount dual amplifier, but the exact electrical names and operating restrictions associated with each terminal should not be inferred from a generic SOIC-8 drawing. Use the manufacturer diagram when assigning PCB tracks, particularly for the power, ground, input, and output terminals of both channels.
Can LT1078IS8 be used with a single 5 V supply?
Yes, the LT1078IS8 is specifically optimized for single-supply operation at 5 V. Analog Devices describes the LT1078 as a micropower dual op amp designed around single-supply use. This makes it particularly suitable for portable and compact systems that derive a common 5 V rail from batteries or a regulator. Input and output common-mode behavior still must remain inside the datasheet limits.
What can replace LT1078IS8 on the same PCB?
LT1078IS8#PBF is a close same-package replacement because it is explicitly listed as an 8-SO dual amplifier from the same LT1078 family. LT1078S8#PBF is another identified 8-SO family option, but its ordering and qualification characteristics should be checked before substitution. Only the exact pin configuration, electrical limits, temperature grade, and required compensation should be confirmed before treating either part as a production drop-in replacement.
Is LT1078IS8 the same as LT1078IS8#PBF?
LT1078IS8 and LT1078IS8#PBF refer to closely related LT1078IS8 ordering designations, with the latter carrying the lead-free finish designation used in the manufacturer ordering code. The manufacturer page identifies LT1078IS8#PBF as an 8-SO, two-circuit operational amplifier. Confirm the exact package marking and current ordering information before treating the designations as interchangeable in production documentation.
When should I choose LT1078IS8 instead of a general-purpose dual op amp?
Choose the LT1078IS8 when the design needs a micropower dual amplifier optimized for a 5 V single supply, particularly in battery-powered instrumentation. Its 600 uV maximum offset voltage supports precision applications, while the approximately 200 kHz gain-bandwidth product is suitable for low-frequency signal conditioning. A general-purpose amplifier may be preferable only when its supply current, bandwidth, offset, and common-mode range better match the design.
Is LT1078IS8 suitable for low-power sensor measurement?
The LT1078IS8 is suitable for many low-power sensor measurement front ends because it combines micropower operation, two amplifier channels, 600 uV maximum offset voltage, and 5 V single-supply optimization. It can buffer or amplify signals from resistive sensors in portable instrumentation. Sensor-specific accuracy also depends on bias current, noise, common-mode range, and the stability of the excitation source, which should be checked in the datasheet.
LT1078IS8 vs LT1078S8#PBF: which is better for an industrial design?
LT1078IS8 is the more appropriate choice when the exact ordering designation specifies the required industrial-grade configuration, while LT1078S8#PBF may carry a different temperature-grade or ordering designation. Both are identified as 8-SO LT1078-family dual amplifiers, but the I and S suffixes should not be treated as interchangeable without checking the manufacturer ordering table. Confirm temperature range, qualification, and marking requirements before PCB reuse.
What is the best cross-brand equivalent for LT1078IS8?
The best cross-brand equivalent is the device whose exact pinout and electrical limits most closely match the LT1078IS8, not merely an amplifier with similar headline bandwidth. A valid replacement must also satisfy the supply range, input common-mode range, offset voltage, bias current, stability, and package dimensions. The retrieved cross-reference results indicate that alternatives exist, but they do not expose enough manufacturer-specific part data to name and validate a cross-brand drop-in replacement safely.
Where can I buy LT1078IS8 and what is its price?
Use the Request a Quote form on this page to request LT1078IS8 availability, unit pricing, and lead time. A formal price cannot be stated reliably because qualified quantity-break pricing for the exact LT1078IS8 ordering code is not present on this product record. The form allows the request to be matched to the required package, quantity, and grade without relying on stale market figures.
Is LT1078IS8 in stock and what is the lead time?
Current LT1078IS8 stock and lead time should be requested through the Request a Quote form on this page. Manufacturer and catalog listings confirm that LT1078IS8-family devices are marketed, but they do not establish a guaranteed stock position for the exact ordering code. Include your required quantity, date code, packaging preference, and acceptable substitutes when submitting the request.
How much power does the LT1078IS8 consume?
The LT1078IS8 is classified as a micropower operational amplifier, but its exact supply-current specification must be read from the Analog Devices datasheet before performing a battery-life calculation. The 200 kHz gain-bandwidth figure identifies speed performance rather than power consumption. Use the manufacturer’s specified supply current at the actual supply voltage, channel state, and operating temperature when estimating total demand.
What application circuit should I use for the LT1078IS8?
The LT1078IS8 is well suited to a 5 V, two-channel precision signal-conditioning front end. One section can buffer a sensor while the other provides gain or an active filter, subject to the datasheet’s common-mode and stability limits. Keep the feedback network close to the relevant amplifier pins, bypass the supply rail, provide a suitable input bias-current return path, and confirm that the selected resistor values remain within the output-current capability.

工程参考数据: LT1078IS8 ——对比、设计指导和合规信息。

选型指南

Choose the LT1078IS8 when a compact, low-power system needs two precision amplifier channels powered from a single 5 V rail. Its 600 uV maximum offset voltage supports low-level DC signal conditioning, and the approximately 200 kHz gain-bandwidth product suits low-frequency measurement, buffering, and control paths. LT1078IS8#PBF is the appropriate same-footprint choice when the required procurement designation is the lead-free finish. Consider LT1078S8#PBF only after confirming that its S-grade temperature and qualification requirements satisfy the product specification. A cross-brand substitute should not be selected from package appearance alone: it must also match the exact pinout, supply range, common-mode limits, offset, bias current, stability behavior, and output capability. For higher bandwidth, lower offset, lower noise, or different supply limits, choose another dual op-amp family rather than treating a cross-reference listing as a guaranteed drop-in replacement.

与替代料对比

参数 本产品 LT1078IS8#PBF LT1078S8#PBF
Package 8-SO 8-SO 8-SO
Brand Analog Devices Analog Devices Analog Devices
Number of Amplifier Circuits 2 circuits 2 circuits 2 circuits
Optimized Supply Voltage 5 V 5 V 5 V
Device Category Micropower precision operational amplifier Micropower dual precision operational amplifier Micropower dual precision operational amplifier
Mounting Type Surface mount Surface mount Surface mount
Ordering Designation LT1078IS8 LT1078IS8#PBF lead-free designation LT1078S8#PBF S-grade designation

关键差异点

  • Two precision amplifier channels in one compact package (对比 LT1078S8#PBF)
  • Optimized for compact 5 V single-supply systems (对比 LT1078IS8#PBF)
  • Precision offset suitable for low-level DC conditioning (对比 LT1078IS8#PBF)

设计说明

Treat the LT1078IS8 as a micropower device but calculate the complete analog-supply budget from the manufacturer’s specified channel and quiescent-current conditions. A single 5 V rail is the intended operating point, yet regulator efficiency, dropout margin, and the load drawn by the external feedback network also affect battery life. Place a local bypass capacitor at the supply pins and route its return directly to the device ground to prevent supply ripple from appearing as amplified input noise.

Use the manufacturer’s 8-SO pin-configuration drawing for every PCB layout and verify pin 1 orientation against the board footprint. Keep the two amplifier channels’ input and feedback paths short, separate from switching nodes and high-current returns. If both channels process correlated signals, use symmetric routing and resistor networks to minimize thermal gradients and channel mismatch. Confirm exposed-pad or thermal requirements against the specific package drawing before release.

Do not treat the 200 kHz gain-bandwidth figure as an unconditional operating frequency at every closed-loop gain. Check the resulting closed-loop bandwidth, output swing, capacitive-load stability, and common-mode range using the manufacturer datasheet. Also verify the input-source impedance against bias-current error and provide a suitable reference path for bipolar-input bias current. These checks are particularly important when the source is a resistive sensor with a long PCB connection.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance attributes were not stated in the retrieved product snippets. The LT1078IS8#PBF ordering code contains a lead-free designation, but that ordering suffix alone was not used to assign the separate lead-free and halogen-free fields. AEC-Q100 qualification is not applicable to this general-purpose operational amplifier.

数据核验日期: 2026-11-14 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

lt1078is8 trpbf lt1078is8 pbf LT1078IS8 datasheet LT1078IS8 datasheet pdf LT1078IS8 pinout LT1078IS8 equivalent LT1078IS8 replacement LT1078IS8 vs LT1078S8#PBF LT1078IS8 footprint LT1078IS8 price LT1078IS8 stock Analog Devices LT1078IS8 LT1078IS8 5V dual op amp LT1078IS8 sensor signal conditioning

相关元器件 & 术语

Analog Devices LT1078IS8 LT1078IS8#PBF LT1078S8#PBF LT1078IS8#TRPBF LT1079 TLC1078CP Operational amplifier Precision operational amplifier Micropower amplifier Dual amplifier Bipolar operational amplifier Single-supply operation 5 V power rail Input offset voltage Gain-bandwidth product 600 uV offset voltage 200 kHz gain-bandwidth product 8-SO package SOIC-8 Surface mount Low-power instrumentation Sensor signal conditioning Current measurement Active feedback
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情