Analog Devices

LT1168IS8 - Low-Power Precision Instrumentation Amplifier | Analog Devices

MPN: LT1168IS8 ✓ Hoạt động
10 nV/√Hz at 1 kHz Vdss 350 µA at ±15 V Id 8-pin SOIC Package
MOQ: 1 |

LT1168IS8 Tóm tắt

The Analog Devices LT1168IS8 is a low-power, single-resistor gain-programmable precision instrumentation amplifier with a gain range of 1 to 10,000, 10 nV/√Hz input-voltage noise at 1 kHz, and 350 µA typical supply current at ±15 V. It is packaged in an 8-pin SOIC and accepts supply voltages from ±2.3 V to ±18 V.

An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals superimposed on larger common-mode voltages. Its internal difference amplifier rejects common-mode noise, while the LT1168 adds internal gain-setting resistors so one external resistor can establish gains up to 10,000. This position in the signal-chain hierarchy—sensor input, differential amplification, then conversion—makes the device useful for bridge transducers, biomedical sensing, and precision current measurement.

The LT1168 combines low-voltage noise of 10 nV/√Hz at 1 kHz with low typical power consumption. Its single-resistor gain programming simplifies board layouts that would otherwise require several precision resistors and an op-amp network. The manufacturer also identifies the LT1168 as a pin-for-pin improved second source for the AD620 and INA118, providing an additional sourcing option for compatible instrumentation-amplifier designs.

The 8-pin SOIC package supports conventional surface-mount assembly and exposes supply, input, output, reference, and gain-resistor connections. With two external 5 kΩ resistors, the LT1168 passes the IEC 1000-4-2 level 4 specification identified by the manufacturer. This ESD capability is relevant when the amplifier is placed near sensors, connectors, or other accessible circuit nodes.

Typical uses include low-level bridge excitation and readout, biomedical instrumentation, battery-powered measurement systems, precision current sensing, and industrial sensor interfaces. The wide ±2.3 V to ±18 V supply range supports both low-voltage portable equipment and higher-voltage industrial systems, subject to the absolute maximum ratings in the manufacturer datasheet.

Designers should use the gain-resistor connection as specified in the manufacturer datasheet and keep the gain-setting component close to the relevant device pins to minimize added noise and parasitic capacitance. Input and reference networks should be laid out away from switching nodes, and supply bypassing should follow the datasheet's recommended application circuit to preserve low-noise operation.

This page combines the manufacturer's electrical and application guidance with drop-in replacement analysis, focused design notes, and parameter comparisons. It is intended to help engineers select the LT1168IS8 for precision low-noise instrumentation while accounting for package compatibility, gain range, supply limits, and system-level noise performance.

Bộ thay thế dễ dàng lắp đặt cho LT1168IS8 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LT1168IS8 (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Gain Range, Number of Circuits, RoHS Status.

Analog Devices
Package: 8-SOIC (0.154", 3.90mm Width)
Amplifier Type: Instrumentation Amplifier
Number of Circuits: 1
So sánh với LT1168IS8 →
Texas Instruments
Package: 8-pin SOIC (D)
Amplifier Type: Instrumentation Amplifier
Gain Range: 1 V/V to 10000 V/V (single external resistor)

AD620ARZ

✅ Drop-In
Analog Devices
📦 8-pin SOIC
Instrumentation Amplifier · 1 · 1 to 10,000 · ±2.3 V to ±18 V · 1.3 mA · 100 dB · 50 µV · 1.0 nA

Liên hệ để biết giá

Xem tài liệu →

INA118U/2K5

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Instrumentation Amplifier · 1 · 50 uV · 0.5 uV/degC · 5 nA · 110 dB · +/-40 V · up to +/-18 V

Liên hệ để biết giá

Xem tài liệu →

LT1168CS8#PBF

✅ Drop-In
📦 8-pin SOIC
Same LT1168 architecture and SOIC footprint; commercial temperature grade differs from industrial-grade LT1168IS8

📋 Tham chiếu thay thế (không có trong danh mục)

LT1168AIS8#PBF

✅ Drop-In
📦 8-pin SOIC
Same LT1168 architecture and SOIC footprint; automotive temperature grade differs from industrial-grade LT1168IS8

📋 Tham chiếu thay thế (không có trong danh mục)

LT1168IS8 Tỷ lệ tối đa & tính chất điện

Amplifier Type Single-resistor gain-programmable precision instrumentation amplifier
Number of Circuits 1 circuit
Gain Range 1 to 10,000
Input Voltage Noise 10 nV/√Hz at 1 kHz
Typical Supply Current 350 µA at ±15 V
Supply Voltage Range ±2.3 V to ±18 V
Hộp 8-pin SOIC
Số lượng chân 8 pins
Kiểu lắp đặt Surface mount
Temperature Grade Industrial
ESD Protection IEC 1000-4-2 level 4 with two external 5 kΩ resistors
Slew Rate 0.5 V/µs
Gain Resistors Required 1 external resistor
Reference Connection 1 pin
Trạng thái RoHS unknown
REACH Status unknown

Cấu hình chân LT1168IS8

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Chân 1 RG — Gain-setting resistor connection
Chân 2 -IN — Inverting differential input
Chân 3 +IN — Non-inverting differential input
Chân 4 V- — Negative supply connection
Chân 5 REF — Reference input for output offset
Chân 6 OUT — Analog output
Chân 7 V+ — Positive supply connection
Chân 8 RG — Gain-setting resistor connection

Ứng dụng tiêu biểu

LT1168IS8 phù hợp cho 6 Áp dụngs: Precision Bridge Sensor Interface, Battery-Powered Biomedical Sensing, Precision Current Shunt Measurement, Industrial Pressure and Strain Monitoring, Low-Level DC Signal Conditioning, Low-Voltage Sensor Acquisition.

🏭

Precision Bridge Sensor Interface

The LT1168IS8 fits precision bridge measurements because its differential instrumentation-amplifier architecture attenuates common-mode voltage while amplifying the small bridge imbalance. One external resistor establishes gains from 1 to 10,000, simplifying the gain network around strain, pressure, and load cells. Its 10 nV/√Hz input noise at 1 kHz limits input-referred noise, although the selected gain also multiplies resistor and reference-network noise. The ±2.3 V to ±18 V supply range supports both portable bridges and higher-voltage industrial installations. Confirm the bridge excitation level, common-mode operating range, signal bandwidth, and allowable input imbalance before finalizing the gain and output scaling.

💊

Battery-Powered Biomedical Sensing

The LT1168IS8 is appropriate for low-power biomedical signal conditioning where sensor outputs are small, differential, and referenced to a large common-mode voltage. Its 350 µA typical supply current at ±15 V reduces amplifier overhead in portable systems, while 10 nV/√Hz input noise at 1 kHz supports high-gain measurement of biopotential and physiological sensor signals. Single-resistor gain programming also reduces the component count compared with discrete resistor networks. For battery operation, recalculate current using the actual supply voltage because the 350 µA figure is specified at ±15 V. Confirm electrode protection, input bias-current requirements, leakage, isolation, and medical qualification separately; the device's electrical suitability does not establish system-level medical compliance.

⚡

Precision Current Shunt Measurement

The LT1168IS8 can amplify the differential voltage produced by a current shunt without requiring the amplifier input to tolerate the full high-side common-mode voltage. Its single-resistor gain programming supports a broad range of measurement spans, from 1 to 10,000, and its low 10 nV/√Hz input noise at 1 kHz improves resolution for small shunt drops. The 8-pin SOIC package permits compact placement close to the shunt and feedback loop. Care is needed because Kelvin routing must avoid copper voltage drops, and the amplifier's input and output limits must be checked at maximum current and fault conditions. Gain error, offset, bandwidth, and shunt power dissipation should be validated together in the final measurement chain.

🏭

Industrial Pressure and Strain Monitoring

The LT1168IS8 suits industrial pressure and strain monitoring systems where long sensor cables can introduce common-mode interference and ground differences. Differential amplification rejects much of that common-mode signal, while the programmable gain of 1 to 10,000 lets one amplifier family cover different mechanical sensitivities. The low-noise rating of 10 nV/√Hz at 1 kHz helps preserve resolution when the bridge output is small. Place the amplifier near the sensor connector when possible, use guarded or differential routing, and isolate switching converters and motor power stages from the input path. Also verify input and output common-mode limits, electrical surge requirements, calibration method, and temperature stability over the operating environment.

🔧

Low-Level DC Signal Conditioning

The LT1168IS8 is useful when a low-level differential DC signal must be conditioned before ADC acquisition. A gain of 1 to 10,000 provides enough scaling to improve the converter's effective input resolution, while the instrumentation topology limits common-mode pickup from cables and nearby digital circuitry. The 10 nV/√Hz input noise at 1 kHz is valuable when large gain is used, and the ±2.3 V to ±18 V supply span permits operation from low-voltage analog rails. Establish the required output range relative to the ADC input span before selecting the gain. Include offset, gain error, bias current, reference noise, and settling time in the error budget, and use the REF connection appropriately if output offset adjustment is needed.

🧩

Low-Voltage Sensor Acquisition

The LT1168IS8 supports compact, low-voltage sensor acquisition systems because it operates from ±2.3 V to ±18 V and consumes 350 µA typically at ±15 V. A wide gain range accommodates outputs from resistive dividers, strain bridges, and current shunts without requiring a separate programmable-gain stage. Its low-voltage noise makes the device useful for compact industrial, IoT, and portable instrumentation, although actual supply current at low voltage must be checked from the datasheet characterization curves. Decoupling capacitors should be placed close to the supply pins, and sensitive input and gain-resistor tracks should remain away from switching nodes. Validate input bias-current error, common-mode range, and ADC acquisition requirements in the completed board.

Tóm tắt các sản phẩm được đề xuất

AD620 Pin-compatible instrumentation-amplifier reference Được sử dụng trong: Precision Bridge Sensor Interface, Battery-Powered Biomedical Sensing, Precision Current Shunt Measurement, Industrial Pressure and Strain Monitoring, Low-Level DC Signal Conditioning, Low-Voltage Sensor Acquisition INA118 Pin-compatible instrumentation-amplifier reference Được sử dụng trong: Precision Bridge Sensor Interface, Battery-Powered Biomedical Sensing, Precision Current Shunt Measurement, Industrial Pressure and Strain Monitoring, Low-Level DC Signal Conditioning, Low-Voltage Sensor Acquisition
What is the LT1168IS8?
The LT1168IS8 is a low-power, single-resistor gain-programmable precision instrumentation amplifier in an 8-pin SOIC package. According to the Analog Devices datasheet, one external resistor can establish a gain from 1 to 10,000. The device is optimized for low-level differential signals operating in industrial and battery-powered measurement systems.
What is the supply voltage range of the LT1168IS8?
The LT1168IS8 operates from ±2.3 V to ±18 V. The Analog Devices datasheet identifies this wide bipolar supply range as suitable for industrial, low-voltage, and battery-powered instrumentation. Designers must also observe the absolute maximum supply and ground-pin limits and must not interpret the operating range as permission to exceed the maximum input or output voltages.
How is the gain set on the LT1168IS8?
The LT1168IS8 uses one external resistor to set its gain, with programmable gains from 1 to 10,000. The Analog Devices datasheet provides the gain-setting equation and associated resistor restrictions. Use the specified resistance and layout practice because parasitic resistance, temperature coefficient, and resistor noise can otherwise reduce the accuracy and noise performance of the selected gain.
What is the input noise of the LT1168IS8?
The LT1168IS8 has an input-voltage noise density of 10 nV/√Hz at 1 kHz. According to the Analog Devices datasheet, this low noise is achieved without increasing typical power dissipation above 350 µA at ±15 V. The specification is especially relevant to high-gain bridge sensors where input-referred noise is magnified by the selected gain.
Where can I download the LT1168IS8 datasheet PDF?
The official LT1168IS8 datasheet PDF is available from Analog Devices at the product-document URL shown on this page. It contains the electrical characteristics, gain-setting information, pin descriptions, applications information, and typical instrumentation-amplifier circuit. Use the manufacturer PDF for the complete ratings and layout guidance associated with the LT1168 family.
Where can I find the LT1168IS8 pinout?
The LT1168IS8 pinout is shown in the manufacturer datasheet and includes eight SOIC connections for gain programming, differential inputs, supply rails, reference, and output. When assigning PCB tracks, use the pin-description table and the standard SOIC-8 numbering shown in the package drawing. Confirm pin orientation against the board footprint before fabrication.
Is the AD620 a drop-in replacement for the LT1168IS8?
The AD620 is a supported drop-in consideration because Analog Devices identifies the LT1168 as a pin-for-pin improved second source for the AD620. The comparison must still account for gain accuracy, bandwidth, input bias current, offset, supply restrictions, and noise. Treat it as a redesign-qualified second source rather than an automatic substitution for every operating condition.
Is the INA118 a drop-in replacement for the LT1168IS8?
The INA118 is a supported drop-in consideration because Analog Devices describes the LT1168 as a pin-for-pin improved second source for the INA118. The two devices should nevertheless be compared for minimum gain, gain error, common-mode range, bandwidth, slew rate, and ESD-network requirements before production substitution.
What is the best drop-in replacement for the LT1168IS8?
The LT1168IS8 has several same-package alternatives, with AD620 and INA118 identified by Analog Devices as pin-for-pin second-source relationships. The most appropriate replacement depends on whether priority is lowest noise, micropower operation, gain accuracy, bandwidth, or exact function. Verify pinout, supply limits, gain range, and application-level performance before releasing a substitution.
When should I choose the LT1168IS8 instead of the AD620?
Choose the LT1168IS8 over the AD620 when its lower-power implementation, single-resistor gain programming, and manufacturer-described pin-for-pin second-source relationship match the system requirements. The AD620 remains appropriate when its established specifications, qualification history, or sourcing align better with the design. Compare the complete datasheets rather than selecting from package appearance alone.
When should I choose the LT1168IS8 instead of the INA118?
Choose the LT1168IS8 when low voltage noise and low typical supply current are central requirements. Its 10 nV/√Hz input noise at 1 kHz and 350 µA typical consumption at ±15 V are attractive for precision battery-powered measurement. Select the INA118 instead when its specific gain, common-mode, and application characteristics are a better functional match.
Is the LT1168IS8 suitable for bridge sensor measurements?
Yes, the LT1168IS8 is suitable for bridge sensor measurements because it combines a gain range of 1 to 10,000 with 10 nV/√Hz input noise at 1 kHz. Its instrumentation-amplifier configuration rejects common-mode signals present on bridge outputs. Signal bandwidth, bridge excitation noise, input common-mode limits, and resistor accuracy must still be checked for the selected bridge.
How much power does the LT1168IS8 consume?
The LT1168IS8 consumes 350 µA typically at ±15 V according to the Analog Devices datasheet. This low supply current makes the device useful in battery-powered instrumentation where amplifier consumption can dominate the power budget. Actual operating current varies with supply voltage and workload, so use the manufacturer characterization curves for final battery-life analysis.
What can replace the LT1168IS8?
The LT1168IS8 can be replaced by compatible 8-pin instrumentation amplifiers such as the AD620 or INA118 after electrical qualification. Analog Devices explicitly describes the LT1168 as a pin-for-pin improved second source for both devices. A valid replacement must preserve the required pin connections and remain acceptable for gain range, noise, bandwidth, common-mode voltage, supply voltage, and ESD behavior.
Where can I buy the LT1168IS8 and check current lead time?
The current commercial status of the LT1168IS8 should be checked through the Request a Quote form on this page. Submit the exact MPN, required quantity, and target package form to obtain current availability, lead time, and a quotation. Quote requests are preferable to relying on a stale catalog record because production and inventory status can change.
What are the key specifications of the LT1168IS8?
The key LT1168IS8 specifications are a 1-to-10,000 programmable gain range, 10 nV/√Hz input-voltage noise at 1 kHz, and 350 µA typical supply current at ±15 V. According to the Analog Devices datasheet, the device supports ±2.3 V to ±18 V supplies and comes in an 8-pin SOIC. Two external 5 kΩ resistors provide IEC 1000-4-2 level 4 ESD performance.

Dữ liệu tham khảo kỹ thuật cho LT1168IS8 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the LT1168IS8 when a precision, low-noise instrumentation amplifier must provide programmable gains from 1 to 10,000 while operating from ±2.3 V to ±18 V and consuming 350 µA typically at ±15 V. Its one-resistor gain-setting arrangement simplifies analog boards, and its 10 nV/√Hz input noise at 1 kHz is valuable for bridge, shunt, and low-level sensor measurements. Choose AD620 when its established electrical characteristics and sourcing fit the design more closely; Analog Devices explicitly supports the LT1168 as a pin-for-pin second source. Choose INA118 when its specific common-mode, gain, and signal-chain characteristics are preferred. For commercial-temperature production, LT1168CS8#PBF preserves the LT1168 architecture; for automotive temperature requirements, evaluate LT1168AIS8#PBF. Regardless of MPN, verify gain accuracy, input bias current, output range, bandwidth, ESD network requirements, and lifecycle status before production release.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này AD620 INA118 LT1168CS8#PBF LT1168AIS8#PBF
Brand Analog Devices Analog Devices Texas Instruments Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Type Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier

Bảo phân biệt quan trọng

  • Single-resistor gain programming with a broad 1-to-10,000 range (vsAD620)
  • Low input noise retained with low typical supply current (vsINA118)
  • Manufacturer-identified pin-for-pin second-source relationship (vsAD620)
  • Configurable temperature-grade sourcing within the LT1168 family (vsLT1168CS8#PBF)

Ghi chú thiết kế

Place the gain-setting resistor close to the RG connections and route the input pair as a short, symmetric pair to minimize parasitic capacitance and loop area. Keep the differential inputs away from switching nodes, inductors, and high-current return paths. The input-reference combination is sensitive to leakage and imbalance, so use guarded grounding where practical and avoid conductive contamination near the input pins.

Use the supply-bypassing arrangement shown in the manufacturer's application guidance and place capacitors directly between the supply pins and their corresponding ground return. Check input common-mode voltage and output swing against the selected ±2.3 V to ±18 V supply range. The 350 µA typical current is specified at ±15 V, so recalculate low-voltage supply consumption from the datasheet characterization data before estimating battery life.

A gain of 10,000 amplifies input-referred offset, bias-current error, resistor noise, and coupled interference as well as the intended signal. Establish an end-to-end error budget at the required temperature range, and avoid using more gain than the sensor output requires. When working near the bandwidth limit, verify settling behavior and slew-rate requirements; the listed 0.5 V/µs slew rate is important for large-signal steps.

Do not treat a matching 8-pin package as sufficient proof of interchangeability. Compare the complete pin functions, gain equation, common-mode range, input and output swing, offset, gain error, bias current, bandwidth, noise, slew rate, and ESD requirements. The REF pin must also be connected according to the manufacturer circuit for the intended output-bias arrangement; otherwise, offset behavior may not match the original design.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The manufacturer identifies IEC 1000-4-2 level 4 ESD performance when two external 5 kΩ resistors are used. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not established by the listed manufacturer and distributor pages.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LT1168IS8 datasheet LT1168IS8 pinout LT1168IS8 datasheet pdf Analog Devices LT1168IS8 LT1168IS8 equivalent LT1168IS8 replacement LT1168IS8 cross reference LT1168IS8 vs AD620 LT1168IS8 vs INA118 LT1168IS8 price LT1168IS8 stock LT1168IS8 application circuit LT1168IS8 SOIC-8 footprint LT1168 10nV/√Hz instrumentation amplifier LT1168IS8 bridge sensor amplifier

Các bộ phận và thuật ngữ liên quan

Analog Devices LT1168IS8 LT1168 AD620 INA118 LT1168CS8#PBF LT1168AIS8#PBF instrumentation amplifier precision instrumentation amplifier difference amplifier analog signal-conditioning IC semiconductor single-resistor gain programming input voltage noise common-mode rejection supply current 8-pin SOIC SOIC package family surface-mount device SMD packaging bridge sensor current shunt biomedical instrumentation IEC 1000-4-2
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ