MAX232BEASE+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MPN: MAX232BEASE+T ✓ Hoạt độngMAX232BEASE+T Tóm tắt
An RS-232 transceiver is an interface IC that bridges the voltage levels used by a host or controller and those used by an RS-232 link. The transmitter portion converts logic-level signals into RS-232-compatible levels, while the receiver portion converts incoming RS-232 signals back into logic-compatible levels. This transceiver category belongs to the broader hierarchy of interface IC, communications IC, and semiconductor.
The MAX232BEASE+T provides a 2/2 full-duplex RS-232 arrangement, meaning that two channels can transmit while two other channels receive. Its +5 V supply operation supports integration with conventional 5 V digital logic. The 16-SOIC package offers a small, surface-mountable footprint, while the -40°C to +125°C rating provides broad temperature coverage for demanding equipment.
RS-232 transceivers are especially useful where point-to-point serial communication must cross a larger voltage range than a CMOS or TTL interface provides. Practical implementations place the transceiver between a UART or communications controller and an external DB9 or equivalent RS-232 connector. Signal integrity depends on correct grounding, cable routing, connector implementation, and compliance with the applicable interface requirements for the finished system.
Typical applications include industrial serial consoles, test and measurement equipment, instrumentation, embedded control systems, and legacy peripheral connections. The two transmitters support independent outgoing channels, while the two receivers support dual incoming paths. Such a configuration can simplify designs that need bidirectional status exchange, acknowledgments, or simultaneous data collection without adding two separate interface packages.
When designing around the MAX232BEASE+T, use the manufacturer pin-description table when assigning PCB nets and preserve the component orientation defined by the pin-1 marker. Decoupling connections and connector protection must follow the layout and application guidance in the MAX232 manufacturer documentation. Firmware should also treat RS-232 as an unbalanced, point-to-point interface rather than a long-distance multidrop network.
This product page consolidates the known MPN, interface, package, and temperature information with application guidance, comparison criteria, and PCB-oriented design notes. It helps engineers identify the correct MAX232 family option while making the package, electrical, sourcing, and replacement requirements easier to evaluate in one place.
Bộ thay thế dễ dàng lắp đặt cho MAX232BEASE+T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX232BEASE+T (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage, Data Rate, Function, Operating Temperature Range.
MAX232ACSE+T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX232ECSE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX232EESE+T
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX232CSE+T
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX232ESE+T
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX232BEASE+T Thông số kỹ thuật
| Product Type | RS-232 transceiver |
| Transmit Channels | 2 |
| Receive Channels | 2 |
| Interface Configuration | 2/2 full-duplex RS-232 |
| Điện áp cung cấp | +5 V |
| Khoảng nhiệt độ hoạt động | -40°C to +125°C |
| Hộp | 16-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Manufacturer | Analog Devices / Maxim Integrated |
Hướng dẫn cấu hình chân MAX232BEASE+T 16-pin soic
Cấu hình chân cho MAX232BEASE+T (16-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX232BEASE+T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX232BEASE+T phù hợp cho 6 Áp dụngs: Industrial Serial Console, Test and Measurement Equipment, Embedded Control Systems, Data Acquisition Systems, Legacy Peripheral Connectivity, Instrumentation and Diagnostics.
Industrial Serial Console
The MAX232BEASE+T fits industrial serial-console designs that require a +5 V interface across -40°C to +125°C. Its two transmitters and two receivers allow a controller UART to connect to an RS-232 port while leaving additional channels for status, acknowledgment, or diagnostic signaling. Place the transceiver close to the connector, route its ground with the signal return path, and use the manufacturer-specified charge-pump capacitors to maintain reliable operation. The extended-temperature rating is particularly useful in equipment whose enclosure may be exposed to temperature variation. Final EMC and ESD performance still depends on the complete board, cable, connector, and enclosure implementation.
Được đề xuất
Test and Measurement Equipment
The MAX232BEASE+T is suitable for test and measurement instruments that exchange commands and results through an RS-232 service port. Its +5 V operation is compatible with conventional controller logic, while the 2/2 full-duplex configuration provides separate paths for command transmission and response reception. Keep the interface path short and away from high-current switching nodes to reduce noise coupling. The verified -40°C to +125°C operating range supports chamber, bench, and industrial test environments. Because RS-232 is an unbalanced interface, engineers should also evaluate ground references, cable length, protection components, and connector shield strategy according to the finished instrument's test requirements.
Được đề xuất
Embedded Control Systems
The MAX232BEASE+T can connect an embedded controller's UART to an external RS-232 device when the system uses a +5 V interface and needs extended-temperature coverage. The two transmitters and two receivers are useful for systems carrying data, control commands, and status information over separate lines. Place the IC and its charge-pump capacitors close to the board's RS-232 connector, and route the UART traces away from motors, relays, and switching regulators. The MAX232BEASE+T's -40°C to +125°C range is advantageous in embedded controllers installed in machinery, vehicle-like environments, or outdoor equipment. Check the connected device's logic levels, handshake requirements, and electrical protection before finalizing the interface.
Được đề xuất
Data Acquisition Systems
The MAX232BEASE+T supports legacy data-acquisition equipment that uses a +5 V RS-232 connection for configuration commands and measurement results. Two transmitters and two receivers provide enough channels for a bidirectional control link or additional acknowledgment paths without duplicating the interface circuitry. Its 16-SOIC package permits compact implementation on control and interface boards. Route the RS-232 traces as a controlled interface path, maintain a continuous ground reference, and apply connector protection appropriate to the installation environment. The -40°C to +125°C operating specification supports industrial equipment, but the complete acquisition system must still meet its own calibration, isolation, noise, and safety requirements.
Được đề xuất
Legacy Peripheral Connectivity
The MAX232BEASE+T is appropriate for connecting a modern controller to legacy peripherals that expose RS-232 rather than modern differential or USB interfaces. Its +5 V supply supports direct integration with common embedded logic, and the 2/2 full-duplex arrangement can accommodate data exchange plus auxiliary control signals. The 16-SOIC footprint keeps the interface compact and compatible with standard surface-mount assembly. Engineers should verify the peripheral's RS-232 voltage levels, connector pinout, flow-control method, and ground relationship before installation. Use the manufacturer pin-description table for PCB implementation and verify charge-pump capacitor values before production release.
Được đề xuất
Instrumentation and Diagnostics
The MAX232BEASE+T can serve as the RS-232 interface in instrumentation and diagnostic equipment that must operate from +5 V and cover a broad temperature range. The two transmitters and two receivers allow a controller to send commands, retrieve data, and manage diagnostic channels through one compact interface package. Place the device near the external connector to minimize exposed trace length, and keep its supply and charge-pump routing compact. Its -40°C to +125°C specification is advantageous in laboratory and industrial environments with variable thermal conditions. The final enclosure and cable design must still address electrostatic discharge, radiated emissions, and ESD protection requirements appropriate to the equipment class.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX232BEASE+T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX232ACSE+T | MAX232ECSE | MAX232EESE+T | MAX232CSE+T | MAX232ESE+T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Interface Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- Higher verified upper operating-temperature limit (vsMAX232ACSE+T)
- Extended-temperature option in the same 16-SOIC footprint (vsMAX232CSE+T)
- Two transmitters and two receivers in one package (vsMAX232ESE+T)
Ghi chú thiết kế
Place the MAX232BEASE+T and its required charge-pump capacitors close to the RS-232 connector. Keep capacitor loops compact, provide a direct ground return, and route the RS-232 traces away from switching nodes and high-current power paths. Use the manufacturer pin-description table to preserve pin-1 orientation and verify every net before fabrication.
The MAX232BEASE+T is specified for +5 V operation. Decouple the supply near the device with the capacitance and placement required by the manufacturer application guidance, and ensure the source can support the charge-pump and output-current demand. Confirm the permitted supply tolerance and capacitor values in the MAX232 datasheet rather than copying them from a different MAX232 suffix.
Do not treat a matching 16-SOIC footprint as sufficient proof of drop-in equivalence. Confirm the channel directions, pinout, supply range, charge-pump capacitor arrangement, temperature grade, and enable or shutdown behavior for every proposed replacement. A suffix change can alter environmental ratings even when the physical footprint remains unchanged.
RS-232 is an unbalanced interface, so ground offsets and cable coupling can affect communication reliability. Maintain a continuous signal-return path, keep the interface connector and transceiver placement controlled, and apply appropriate connector-side transient protection. Evaluate the finished board for radiated emissions and immunity because component placement alone cannot guarantee system compliance.
Thông tin tuân thủ
Compliance attributes require confirmation in the current Analog Devices product documentation or declaration of conformity.