MAX232EWE+ - Dual RS-232 Transceiver, 5V | Maxim
MPN: MAX232EWE+ ✓ Hoạt độngMAX232EWE+ Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. In the product hierarchy, the MAX232EWE+ is a dual line transceiver within the broader RS-232 interface IC and semiconductor categories. Its two driver and two receiver channels allow one connector to carry two independent RS-232 data paths, reducing the number of interface components required in multi-channel equipment.
The principal operating characteristics are a 4.5 V to 5.5 V supply range, 120 kbps maximum data rate, two transmitters, two receivers, CMOS-compatible logic, and a 16-pin SOIC package. The E in the EWE package code identifies the manufacturer’s specified package variant, while the plus suffix denotes the current ordering designation shown in the product listings. The wide SOIC package measures 7.50 mm across the width dimension stated in the product record.
The MAX232 family uses integrated charge-pump circuitry to generate the positive and negative voltage levels required by RS-232. Those levels allow the interface to overcome the voltage thresholds and noise margin associated with unbalanced, single-ended communications. Because the device includes both transmit and receive functions, each logical channel can use one driver and one receiver when full-duplex point-to-point communication is required.
Typical uses include industrial serial-control equipment, test and measurement instruments, data acquisition systems, point-of-sale terminals, and embedded control systems that expose an RS-232 port. It is most appropriate where a legacy RS-232 interface must coexist with a 5 V CMOS or TTL control platform. USB-to-RS-232 conversion is another possible use when the host controller already provides UART-compatible logic signals.
PCB layout should keep the interface and charge-pump components close to the device and should route the RS-232 traces away from sensitive analog and high-speed digital signals. Decoupling capacitors must follow the capacitor-selection and layout guidance in the manufacturer datasheet. Before substituting a different transceiver, verify the complete pinout, supply range, driver and receiver counts, maximum data rate, logic thresholds, and connector-side voltage levels rather than relying on package dimensions alone.
This page organizes the MAX232EWE+ specifications, practical design considerations, application guidance, and qualified drop-in alternatives into an engineering-focused reference. It also distinguishes the known channel, speed, voltage, and package characteristics from parameters that require confirmation in the manufacturer datasheet before production release.
Bộ thay thế dễ dàng lắp đặt cho MAX232EWE+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX232EWE+ (cùng hình factor và footprint) — khác nhau ở Interface Standard, Product Type, Package, Number of Drivers, Number of Receivers.
MAX232CWE+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX232CWE+T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX232DW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX233ACWP-T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX232EWE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX232EWE+ Thông số kỹ thuật
| Product Type | Dual RS-232 transceiver |
| Interface Standard | RS-232 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Number of Drivers | 2 channels |
| Number of Receivers | 2 channels |
| Maximum Data Rate | 120 kbps |
| Logic Technology | CMOS |
| Transceiver Configuration | 2 transmitter and 2 receiver channels |
| Hộp | 16-pin SOIC |
| Package Width | 7.50 mm |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MAX232EWE+ 7.50 mm
Cấu hình chân cho MAX232EWE+ (7.50 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX232EWE+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX232EWE+ phù hợp cho 6 Áp dụngs: Industrial Serial Control Ports, Test and Measurement Instruments, Data Acquisition Systems, Point-of-Sale and Retail Terminals, USB-to-RS-232 Adapter Electronics, Embedded Control and Service Interfaces.
Industrial Serial Control Ports
The MAX232EWE+ is appropriate for industrial equipment that must expose one or two RS-232 control ports to a legacy controller. Its two drivers and two receivers support paired point-to-point channels, while the 120 kbps maximum rate is more than sufficient for command, configuration, and diagnostic traffic. Operating from a 4.5 V to 5.5 V supply allows the interface to sit alongside 5 V CMOS or TTL digital logic. The product is used between the host UART or logic-level connector and an external DE-9 or DB-style RS-232 connector. Protection against industrial surge and ESD events must be handled at the connector and power-entry architecture rather than assumed from the logic-side specifications.
Được đề xuất
Test and Measurement Instruments
The MAX232EWE+ can provide a simple RS-232 control link for laboratory instruments, programmable supplies, and automated test equipment. Two transmitters and two receivers allow the instrument to maintain separate command and response channels when the system requires independent hardware paths. Its 120 kbps data-rate capability supports typical instrument-control protocols without demanding a high-speed differential interface. The 5 V supply range matches common embedded control platforms, and the 16-pin SOIC package permits straightforward assembly on a mixed-signal instrument board. Designers should keep the RS-232 side away from precision analog sections and follow the manufacturer’s recommended capacitor placement to minimize charge-pump and digital coupling.
Được đề xuất
Data Acquisition Systems
The MAX232EWE+ fits legacy data-acquisition equipment that must transfer measurement-control information over RS-232. Two RS-232 channels can connect separate instruments or support bidirectional communication when each channel uses one transmitter and one receiver. The 120 kbps ceiling is suitable for many low- and moderate-rate acquisition-control protocols, although it does not determine the final throughput of a particular command set. A 4.5 V to 5.5 V operating range allows the transceiver to share power with suitable control electronics. For installations with long cables or noisy industrial environments, use a protected connector path and validate the complete system against the receiver thresholds defined in the manufacturer datasheet.
Được đề xuất
Point-of-Sale and Retail Terminals
The MAX232EWE+ can bridge a 5 V embedded controller in a point-of-sale terminal to an RS-232 peripheral such as a scanner, printer, or customer display. The device’s two drivers and two receivers permit two peripheral connections when the system architecture assigns separate transmit and receive paths. Its 120 kbps maximum data rate comfortably covers common peripheral-control traffic, while the CMOS-compatible logic side avoids requiring older bipolar interface levels internally. Designers should account for ESD exposure at externally accessible connectors, isolate the interface from noisy switching supplies, and keep the charge-pump capacitors close to the device. The enclosure and cable arrangement will often determine real-world reliability more than the logic-side UART implementation.
Được đề xuất
USB-to-RS-232 Adapter Electronics
The MAX232EWE+ is useful in USB-to-RS-232 adapter hardware where a USB controller provides a UART-compatible logic interface to the converter. The two transmitters and two receivers can support both a primary port and an additional auxiliary channel, subject to the USB bridge’s pin and protocol support. The MAX232EWE+ operates from 4.5 V to 5.5 V and handles up to 120 kbps, covering common serial-port adapter data rates. Its wide 16-pin SOIC package provides adequate routing flexibility between the digital controller and the connector area. For a production adapter, verify USB-to-UART voltage levels, select the connector-side protection strategy, and follow the layout guidance that keeps switching and high-speed USB traces away from the RS-232 network.
Được đề xuất
Embedded Control and Service Interfaces
The MAX232EWE+ can preserve a service or diagnostic connector on an embedded control system while the main board uses modern digital interfaces. Its two-channel arrangement allows service commands to be separated from another RS-232 function, and the 120 kbps rate is appropriate for firmware logs, configuration exchanges, and diagnostic protocols. Because the transceiver is powered from a 4.5 V to 5.5 V rail, the design must ensure the host logic and the interface share compatible levels. Firmware should also handle electrical noise and unexpected connector states at the software layer. A separate protection network and careful ground-return arrangement remain necessary when the service port is exposed to users or connected to longer field cables.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX232EWE+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX232CWE+ | MAX232CWE+T | MAX232DW | MAX233ACWP-T | MAX232EWE |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC wide | 16-SOIC wide | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | 4.5 V to 5.5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps | 120 kbps | 120 kbps | 120 kbps |
| RS-232 Transceiver Configuration | Full RS-232 | RS-232 transceiver | RS-232 transceiver | Dual transmitter and receiver | Dual transmitter and receiver | 2 drivers and 2 receivers |
Bảo phân biệt quan trọng
- Provides two complete RS-232 channels in one 16-SOIC device (vsMAX232EWE)
- Supports a maximum data rate of 120 kbps (vsMAX232CWE+)
- Matches the principal ratings of the wide-SOIC MAX232DW (vsMAX232DW)
Ghi chú thiết kế
Place the charge-pump capacitors and supply bypass capacitor close to their associated MAX232EWE+ pins, following the manufacturer datasheet schematic and loop guidance. Keep the capacitor connections short and place them on the same PCB side as the device where practical. Route the RS-232 driver and receiver nets toward the connector while separating them from sensitive analog inputs, clock signals, and switching-power circuits.
Preserve the device’s ground return and route RS-232 signals as a differential pair of conductors in the physical cable even though the interface signals themselves are single-ended. At the PCB connector, keep the logic-side ground and cable-side return path continuous. Avoid long stubs between the transceiver and connector, and place any external protection network directly at the connector entry so surge current is not forced through traces around the IC.
Do not treat matching the SOIC body width as sufficient proof of drop-in compatibility. Before replacing the MAX232EWE+, verify every pin name, the 4.5 V to 5.5 V supply range, the 120 kbps operating limit, operating-temperature grade, logic thresholds, receiver behavior, and the required charge-pump capacitors. The MAX233ACWP-T has a different receiver behavior even though its principal channel-count, voltage, and data-rate ratings align.
Thông tin tuân thủ
The searchable product records do not state a definitive compliance result for the exact MAX232EWE+ ordering code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from the current manufacturer documentation before release.