MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3221CPWRE4 ✓ Hoạt độngMAX3221CPWRE4 Tóm tắt
An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into the positive and negative voltage swings used by RS-232 equipment. In the broader semiconductor hierarchy, the MAX3221 belongs to the interface IC family, where line drivers and line receivers bridge computer, industrial-control, instrumentation, and communications equipment. Its single-channel architecture is useful when a system needs one bidirectional RS-232 connection rather than the multiple channels found on multi-channel transceiver families.
The MAX3221 operates from 3 V to 5.5 V and accepts 5 V logic input when operated from a 3.3 V supply. Its 250 kbit/s data rate supports legacy serial-port, point-to-point control, and embedded equipment links. Pin-to-pin ESD protection of ±15 kV applies to the RS-232 connection pins, including ground, helping protect the interface against electrostatic discharge encountered during installation or handling.
Internally, the device combines one line driver, one line receiver with a dedicated enable input, and a dual charge-pump circuit. The charge pumps generate the positive and negative voltages required for compliant RS-232 signaling. The receiver enable function allows a system to place the receive side in a controlled state, while the low standby current supports power-conscious designs where the interface must remain present without continuously receiving data.
Typical uses include single-port RS-232 equipment interfaces, industrial controller serial links, programmable-instrument connections, and embedded systems that communicate with legacy peripherals. Because the logic side operates from 3 V to 5.5 V, the device can be used in both 3.3 V and 5 V systems. The 16-pin TSSOP also supports compact board layouts where a larger multi-channel transceiver would be unnecessary.
Designers should place the 0.1 µF charge-pump capacitors close to their designated pins and observe the connector-side voltage and polarity requirements of RS-232. The interface does not create isolation, so an exposed or long cable run may require additional surge and ground-management measures. Input and output logic levels must also be checked against the connected controller rather than assumed from the serial-port standard.
This page organizes the technical specifications, source links, interface applications, drop-in alternatives, and PCB considerations for engineers evaluating the MAX3221CPWRE4. It also distinguishes exact electrical matches from variants that change package details or feature sets, helping prevent a nominal substitution from creating an unintended PCB or firmware incompatibility.
Bộ thay thế dễ dàng lắp đặt cho MAX3221CPWRE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX3221IPWR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3221ECPWRE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3221CPWRE4 Thông số kỹ thuật
| Device Type | Single-channel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Line Drivers | 1 |
| Line Receivers | 1 with dedicated enable pin |
| Charge-Pump Architecture | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 0.1 µF |
| ESD Protection | ±15 kV pin-to-pin on serial-port connection pins, including GND |
| RS-232 Compliance | TIA/EIA-232-F |
| ITU Recommendation | ITU V.28 |
| Low Standby Current | 1 µA typical |
| Logic Input Compatibility | Accepts 5 V logic input with 3.3 V supply |
| Hộp | 16-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân MAX3221CPWRE4
| Chân 1 | C1+ — Charge-pump capacitor 1 positive terminal |
| Chân 2 | C1- — Charge-pump capacitor 1 negative terminal |
| Chân 3 | C2+ — Charge-pump capacitor 2 positive terminal |
| Chân 4 | C2- — Charge-pump capacitor 2 negative terminal |
| Chân 5 | T1OUT — Transmitter 1 output |
| Chân 6 | R1IN — Receiver 1 input |
| Chân 7 | R1OUT — Receiver 1 output |
| Chân 8 | R2OUT — Receiver 2 output |
| Chân 9 | T2IN — Transmitter 2 input |
| Chân 10 | T2OUT — Transmitter 2 output |
| Chân 11 | V- — Negative charge-pump output |
| Chân 12 | R2IN — Receiver 2 input |
| Chân 13 | VCC — Positive supply voltage |
| Chân 14 | GND — Ground |
| Chân 15 | EN — Receiver enable input |
| Chân 16 | T1IN — Transmitter 1 input |
Ứng dụng tiêu biểu
MAX3221CPWRE4 phù hợp cho 6 Áp dụngs: Legacy RS-232 Equipment Interface, Industrial Controller Serial Link, Programmable Instrumentation Communication, Embedded System RS-232 Port, RS-232 Service and Configuration Port, Data Acquisition and Control Module.
Legacy RS-232 Equipment Interface
The MAX3221CPWRE4 fits a point-to-point connection to legacy RS-232 equipment because it combines one line driver, one line receiver, and a dual charge-pump circuit in a compact 16-pin TSSOP. Its 250 kbit/s maximum data rate covers conventional serial-port control and diagnostic links. The 3 V to 5.5 V operating range also permits use with both 3.3 V and 5 V control logic. Designers should use the receiver-enable function when the host needs a controlled receive state and should verify the exact operating-temperature grade before using the part in industrial equipment.
Được đề xuất
Industrial Controller Serial Link
A MAX3221CPWRE4 can provide the electrical interface between an industrial controller and a single RS-232 peripheral or service port. Its ±15 kV pin-to-pin ESD protection on the serial-port connection pins adds useful defense for connector-facing circuitry, while the dual charge-pump circuit develops the required RS-232 voltage levels internally. The single-channel format reduces board area compared with a multi-channel transceiver. For installed industrial equipment, verify the exact temperature grade, implement appropriate cable grounding, and determine whether galvanic isolation or additional surge protection is required.
Được đề xuất
Programmable Instrumentation Communication
The MAX3221CPWRE4 is suitable for connecting a controller to programmable test and measurement equipment that retains an RS-232 communication port. A 250 kbit/s interface rate is appropriate for command and measurement-data transfers that do not require modern high-speed serial protocols, while the 3 V to 5.5 V supply range simplifies operation across mixed-voltage control systems. Place the two 0.1 µF charge-pump capacitors close to the device and route connector-side signals away from sensitive logic to minimize coupling.
Được đề xuất
Embedded System RS-232 Port
An embedded controller can use the MAX3221CPWRE4 to add one full-duplex-style RS-232 port without implementing a discrete driver, receiver, and charge-pump network. Logic-side operation from 3 V to 5.5 V supports common embedded supply choices, and 5 V logic inputs remain acceptable with a 3.3 V supply. The dedicated receiver-enable input can assist with interface-state management. Firmware and signal timing must still follow the connected device's RS-232 protocol, and the 250 kbit/s limit should be checked against the required payload rate.
Được đề xuất
RS-232 Service and Configuration Port
The MAX3221CPWRE4 can implement a compact service, configuration, or maintenance connector on industrial and communications equipment. A single driver and receiver are sufficient for a service port, and the 16-pin TSSOP package keeps the interface compact. Its 250 kbit/s maximum data rate supports typical command menus and diagnostic transfers. The connector-facing ±15 kV ESD protection helps with exposed interfaces, but it does not eliminate the need for suitable cable design, chassis grounding, or an isolated protection network in severe industrial environments.
Được đề xuất
Data Acquisition and Control Module
The MAX3221CPWRE4 can connect a compact data-acquisition or control module to an RS-232 host for commands, status reporting, and sampled data transfer. The single-channel architecture matches systems with one external serial port, while 250 kbit/s operation is suitable for moderate legacy data rates. Its 3 V to 5.5 V supply range permits common 3.3 V logic systems, and the receiver-enable input gives the host interface additional state control. Validate throughput, framing, and flow-control timing against the acquisition protocol before production deployment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3221CPWRE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3221IPWR | MAX3221ECPWRE4 |
|---|---|---|---|
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Function | Single-channel RS-232 driver/receiver | Single-channel RS-232 driver/receiver | Single-channel RS-232 driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| ESD Protection | ±15 kV pin-to-pin | ±15 kV pin-to-pin | ±15 kV pin-to-pin |
| External Charge-Pump Capacitors | 0.1 µF | 0.1 µF | 0.1 µF |
| RS-232 Standard | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 |
| Receiver Enable | Dedicated enable pin | Dedicated enable pin | Dedicated enable pin |
Bảo phân biệt quan trọng
- Compact single-channel interface (vsMAX3221ECPWRE4)
- Wide logic-side supply compatibility (vsMAX3221IPWR)
- Connector-side electrostatic-discharge protection (vsMAX3221IPWR)
Ghi chú thiết kế
Place the two 0.1 µF charge-pump capacitors close to the C1 and C2 terminals identified in the manufacturer pin-description table. Keep the capacitor loops compact and route them away from the RS-232 connector and switching-power circuits. Short charge-pump traces reduce radiated coupling and help the charge-pump circuitry maintain predictable operation near the documented 250 kbit/s data-rate limit.
Separate connector-side RS-232 nets from sensitive logic and analog traces. The driver output is intentionally a high-voltage RS-232 signal, so routing it beneath sensitive circuitry can increase coupling even when the connector is unpopulated. Use a suitable ground reference for the interface, maintain the recommended connector-side clearances, and check whether the system requires isolated logic rather than a direct device ground connection.
Do not infer that every MAX3221 suffix is electrically and thermally interchangeable. Before substituting a related ordering code, compare the manufacturer ordering table, exact temperature range, pin configuration, package dimensions, marking, qualification status, and lifecycle status. The receiver enable state and 3 V to 5.5 V supply operation should also be checked against the host firmware and power-sequencing requirements.
Thông tin tuân thủ
The manufacturer documentation confirms TIA/EIA-232-F and ITU V.28 operation. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not explicitly established by the cited source text and remain unknown.