Analog Devices

MAX3385ECAP - 250kbps True RS-232 Transceiver | Analog Devices

MPN: MAX3385ECAP ✓ Hoạt động
3.0V to 5.5V Vdss EIA/TIA-232 and V.28/V.24 Rds(on) 20-pin SSOP Package
MOQ: 1 |

MAX3385ECAP Tóm tắt

The Analog Devices MAX3385ECAP is a 2/3 transceiver with integrated charge pump and true RS-232 line drivers and receivers, operating from 3.0V to 5.5V at data rates up to 250kbps. The device is packaged in a 20-pin SSOP and provides 15kV ESD protection on its serial interface.

An RS-232 transceiver is an interface integrated circuit that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. A line driver translates logic states into RS-232-compatible outputs, while a line receiver performs the reverse conversion. The MAX3385ECAP integrates one driver and two receivers, commonly described as a 2/3 transceiver, for asymmetric point-to-point communication links.

The MAX3385ECAP supports supply voltages from 3.0V to 5.5V, allowing operation from common 3.3V and 5V systems. Its maximum guaranteed data rate is 250kbps, making it suitable for point-to-point industrial control, instrumentation, data acquisition, and embedded equipment. The 15kV ESD rating strengthens its suitability for connectors and cables exposed to electrostatic discharge.

Its dual charge-pump architecture generates the positive and negative voltages required for true RS-232 output levels without a separate negative supply rail. The manufacturer datasheet states that four 0.1uF capacitors are sufficient for operation from a 3.3V supply. A proprietary low-dropout transmitter output stage helps maintain compliant output levels across the supported supply range while controlling power consumption.

Typical uses include serial configuration ports, test and measurement equipment, industrial controllers, barcode scanners, printers, and external data-acquisition modules. The 20-pin SSOP package supports compact surface-mount layouts, while the combination of 3.0V minimum supply, 250kbps throughput, and 15kV ESD protection makes the device appropriate for short-distance point-to-point links where logic-level UART signaling must cross an RS-232 cable.

Pay attention to charge-pump capacitor placement and signal routing during PCB layout. Keep the charge-pump capacitors close to their associated pins, provide an uninterrupted ground reference beneath the interface, and route driver outputs and receiver inputs away from noisy switching nodes. These measures preserve signal integrity and reduce the chance that charge-pump switching activity will disturb adjacent circuitry.

This product page combines the manufacturer interface specifications, package information, pricing availability, and practical RS-232 design guidance. It also distinguishes confirmed drop-in alternatives from functionally similar devices that require pinout, package, and operating-limit verification before substitution.

Bộ thay thế dễ dàng lắp đặt cho MAX3385ECAP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

MAX3385ECAP+

✅ Drop-In
📦 20-pin SSOP
Same 2-transmitter, 3-receiver RS-232 implementation, 3.0 V to 5.5 V supply, and up to 250 kbps; ordering-code presentation differs by 0%

📋 Tham chiếu thay thế (không có trong danh mục)

MAX3385ECAP Thông số kỹ thuật

Product Type 2/3 RS-232 transceiver
Supply Voltage Range 3.0V to 5.5V
Maximum Data Rate 250kbps
ESD Protection 15kV
Line Drivers 1 driver
Line Receivers 2 receivers
Interface Standard True RS-232
Communication Standards EIA/TIA-232 and V.28/V.24
Charge Pump Dual charge pump
Required Charge Pump Capacitors 4 x 0.1uF at a 3.3V supply
Transmitter Output Stage Proprietary low-dropout output stage
Power Classification Low-power device
Hộp 20-pin SSOP
Package Pin Count 20 pins
Terminal Form Gull wing
Package Shape Rectangular
Temperature Grade Commercial

Hướng dẫn cấu hình chân MAX3385ECAP rectangular

Cấu hình chân cho MAX3385ECAP (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân rectangular cho MAX3385ECAP

Không có dữ liệu chân cụ thể sẵn có cho MAX3385ECAP.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MAX3385ECAP phù hợp cho 6 Áp dụngs: Industrial Controller Serial Port, Test and Measurement Equipment, Data Acquisition Module, Point-to-Point Configuration Port, Printer and Barcode Scanner Interface, Embedded Serial Communications Module.

🏭

Industrial Controller Serial Port

The MAX3385ECAP is appropriate for a short-distance RS-232 link between an industrial controller and a service terminal, programming fixture, or external accessory. Its 3.0V to 5.5V supply range supports both 3.3V embedded systems and conventional 5V control electronics, while the guaranteed 250kbps rate supports status polling and configuration transfers. The integrated dual charge pump avoids a separate negative supply, and four 0.1uF capacitors are sufficient at 3.3V. Place the charge-pump capacitors close to the device and maintain a continuous ground return to reduce coupling from the switching charge-pump circuitry.

🔧

Test and Measurement Equipment

The MAX3385ECAP can interface a test instrument, data logger, or automated measurement system with a legacy RS-232 controller. A 250kbps maximum data rate provides useful margin for transferring readings and commands, while the 15kV ESD rating is beneficial when the serial port connects to bench equipment or external cables. The 20-pin SSOP package saves board area, although designers should reserve adequate clearance around the connector and transceiver. Verify the required 3.3V or 5V rail, configure the charge-pump capacitors exactly as shown in the manufacturer application circuit, and test the complete cable and grounding arrangement.

📊

Data Acquisition Module

The MAX3385ECAP fits portable and rack-mounted data-acquisition modules that must communicate with a host computer over RS-232. Its low-power 3.0V to 5.5V operation reduces supply complexity, and the dual charge pump provides true RS-232 levels without requiring a negative input rail. At rates up to 250kbps, the interface can carry sampled status and control information efficiently. Keep the receiver path away from motors, relay contacts, and switching regulators, and provide a low-impedance ground connection between the module and host. Select capacitors with adequate DC bias and temperature characteristics for the charge-pump network.

💻

Point-to-Point Configuration Port

The MAX3385ECAP is well suited to firmware-loading, configuration, and maintenance ports where a compact board needs a dedicated RS-232 connection. The 20-pin SSOP footprint supports surface-mount assembly, while operation from a single 3.3V or 5V rail simplifies interface design. Its 250kbps capability allows faster upload and download procedures than a low-speed UART transceiver. Add connector retention and chassis grounding at the product boundary, and avoid long unprotected traces between the IC and connector. The interface's 15kV ESD rating should not be treated as a substitute for a properly engineered enclosure and cable system.

📱

Printer and Barcode Scanner Interface

The MAX3385ECAP can provide the RS-232 electrical interface for a printer, barcode scanner, label reader, or other peripheral using point-to-point serial communication. Its 250kbps maximum rate exceeds the needs of many low-speed scanner protocols, while the 3.0V to 5.5V operating range permits flexible host-logic integration. The integrated dual charge pump eliminates the need for a negative system rail. Confirm signal polarity, handshake support, connector pin assignment, and cable length for the selected peripheral, because protocol compatibility and electrical compatibility are separate requirements. Route the driver output directly toward the connector and keep it away from sensitive receiver traces.

🌐

Embedded Serial Communications Module

The MAX3385ECAP can add an RS-232 port to an embedded communications module built around a 3.3V microcontroller or processor. The device bridges UART logic signals to true RS-232 levels, uses a dual charge pump, and requires only four 0.1uF capacitors for 3.3V operation according to the Analog Devices MAX3385E datasheet. This simplifies systems that cannot allocate a negative supply rail. Match the UART logic levels and baud-rate range of the host controller, and follow the manufacturer capacitor placement and routing guidance. For a new layout, evaluate the transceiver near the connector while maintaining separation from switching power and high-current return paths.

Tóm tắt các sản phẩm được đề xuất

MAX3221E Related single-driver RS-232 interface Được sử dụng trong: Industrial Controller Serial Port, Data Acquisition Module, Point-to-Point Configuration Port, Printer and Barcode Scanner Interface, Embedded Serial Communications Module MAX3232E Related 2/2 RS-232 interface Được sử dụng trong: Industrial Controller Serial Port, Test and Measurement Equipment, Point-to-Point Configuration Port, Embedded Serial Communications Module MAX3241E Related multi-driver RS-232 interface Được sử dụng trong: Industrial Controller Serial Port, Test and Measurement Equipment, Printer and Barcode Scanner Interface ISL83385ECA Related 3V RS-232 transceiver candidate Được sử dụng trong: Data Acquisition Module, Embedded Serial Communications Module
What is the operating voltage of MAX3385ECAP?
The MAX3385ECAP operates from 3.0V to 5.5V. According to the Analog Devices MAX3385E datasheet, this range supports both 3.3V and 5V systems. The dual charge-pump architecture generates the bipolar voltage levels required for true RS-232 transmission from this single positive supply. Four 0.1uF capacitors are sufficient for charge-pump operation at a 3.3V supply.
What are the key specifications of MAX3385ECAP that engineers should know?
The MAX3385ECAP is a 20-pin SSOP RS-232 transceiver with one driver, two receivers, a 3.0V to 5.5V supply range, and operation up to 250kbps. The Analog Devices MAX3385E datasheet also identifies 15kV ESD protection and a dual charge pump. Its low-dropout transmitter stage maintains true RS-232 output behavior while allowing operation from a single 3.3V or 5V rail.
What is the maximum data rate of MAX3385ECAP?
The MAX3385ECAP is guaranteed to operate at data rates up to 250kbps. According to the Analog Devices MAX3385E datasheet, the device maintains RS-232 output levels across that operating range. This makes it appropriate for short-distance UART links carrying configuration, status, measurement, or control data where higher data rates than a conventional low-speed RS-232 port are required.
What is the difference between MAX3385ECAP and MAX3385ECAP+?
Both MAX3385ECAP and MAX3385ECAP+ identify a 20-terminal commercial SSOP RS-232 transceiver from Maxim Integrated, but the available listing does not explicitly define an electrical difference between the base and plus designations. The manufacturer MAX3385E datasheet describes the device family. Confirm package suffix, lead finish, ordering code, and approved-source status before treating the two designations as interchangeable in a released BOM.
Can MAX3385ECAP operate from a 3.3V supply?
Yes, the MAX3385ECAP can operate from a 3.3V supply within its 3.0V to 5.5V input range. The Analog Devices MAX3385E datasheet specifies four 0.1uF capacitors for charge-pump operation at 3.3V. Confirm capacitor voltage ratings, effective capacitance, and placement against the manufacturer guidance when applying the part in a low-voltage design.
Does MAX3385ECAP require a negative power supply?
No external negative supply is required for the MAX3385ECAP. Its dual charge pump derives the bipolar voltages needed for true RS-232 outputs from the 3.0V to 5.5V positive supply. According to the Analog Devices MAX3385E datasheet, four 0.1uF capacitors are sufficient for operation from 3.3V, simplifying designs that cannot provide a negative rail.
What ESD protection does MAX3385ECAP provide?
The MAX3385ECAP provides 15kV ESD protection for its RS-232 interface. This protection is identified in the Analog Devices MAX3385E datasheet and is valuable when the serial connector is connected to user-accessible cabling. ESD protection reduces the risk of interface damage, although it does not replace correct connector grounding, shielding, and system-level signal-integrity practices.
Where can I download the MAX3385ECAP datasheet PDF?
The official MAX3385ECAP datasheet PDF is available from Analog Devices at the MAX3385E datasheet link on this page. It describes the 3.0V to 5.5V operating range, 250kbps data rate, dual charge pump, transmitter architecture, and four 0.1uF capacitor requirement. Use the manufacturer document for final pin assignments, electrical characteristics, timing information, and recommended application circuitry.
Where can I find the MAX3385ECAP pinout?
Use the pin-description table and package drawing in the Analog Devices MAX3385E datasheet to assign the MAX3385ECAP pins. The component uses a 20-pin SSOP package with gull-wing terminals. The pinout image on this page is selected for that package, but individual signal names are not reproduced here because the manufacturer pin table was not included in the product records used for this page.
When should I choose MAX3385ECAP over a lower-speed RS-232 transceiver?
Choose the MAX3385ECAP when the link must operate faster than a conventional low-speed RS-232 interface or needs its 15kV ESD-protected 2/3-transceiver arrangement. The device is guaranteed up to 250kbps and supports 3.0V to 5.5V operation. A lower-speed device may be adequate for simple control ports, but it can limit UART throughput and offer less margin for exposed serial cabling.
Is MAX3385ECAP suitable for industrial and instrumentation RS-232 ports?
The MAX3385ECAP is suitable for many industrial and instrumentation RS-232 ports because it combines 250kbps operation, a 3.0V to 5.5V supply range, and 15kV ESD protection. According to the Analog Devices MAX3385E datasheet, it supports the EIA/TIA-232 and V.28/V.24 interfaces. Final qualification still depends on the enclosure, cable length, grounding, surge exposure, and environmental requirements of the finished equipment.
What is the best drop-in replacement for MAX3385ECAP?
The MAX3385ECAP is a 20-pin SSOP 2/3 transceiver, and no replacement can be called a confirmed drop-in without matching its pinout, package, supply range, data rate, and ESD rating. The available cross-reference material identifies the Intersil ISL83385ECA as functionally similar, but it does not establish identical pin compatibility. Treat it as a redesign candidate until its datasheet and footprint have been compared.
What can replace MAX3385ECAP?
MAX3221E, MAX3232E, MAX3241E, and ISL83385ECA are functionally similar RS-232 interface devices identified in the product cross-reference information. However, functional similarity alone does not prove drop-in compatibility with the MAX3385ECAP's 20-pin SSOP footprint. Check lead count, pin functions, driver and receiver counts, charge-pump capacitor values, supply range, data rate, and ESD rating before selecting a replacement.
MAX3385ECAP vs ISL83385ECA - which is better for a 3.3V RS-232 link?
MAX3385ECAP is the better choice when its 20-pin SSOP pinout can be used directly because it is guaranteed to 250kbps and provides 15kV ESD protection. The ISL83385ECA is described as functionally similar, but the comparison material notes that its circuit structure may differ. For a new 3.3V design, compare both datasheets and PCB footprints before deciding; for an existing board, assume a footprint change until proven otherwise.
Where can I buy MAX3385ECAP and how do I request a quote?
Use the Request a Quote form on this page to ask about MAX3385ECAP availability, current lead time, and commercial terms. The target device is the 20-pin SSOP MAX3385ECAP, so quote that exact MPN and the 20-SSOP package requirement. Some listings identify the tape-and-reel suffix MAX3385ECAP-T, which should not be substituted automatically when the assembled production package must remain MAX3385ECAP.
What is the price and lead time of MAX3385ECAP?
Current price, stock, and lead time for MAX3385ECAP should be requested through the Request a Quote form on this page. The available distributor pages identify the component and its 20-SSOP package, but they do not provide a qualifying quantity-break table for the exact MPN. State the required quantity, package suffix, date code, and shipping destination so the quotation reflects the exact production requirement.

Dữ liệu tham khảo kỹ thuật cho MAX3385ECAP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MAX3385ECAP when a design needs a compact 20-pin SSOP interface that operates from 3.0V to 5.5V, supports rates up to 250kbps, and provides 15kV ESD protection. It is particularly useful for short point-to-point links that require true RS-232 levels from a single positive supply and do not need more than one driver or two receivers. MAX3221E may suit simpler single-driver links, while MAX3232E and MAX3241E cover different receiver and driver arrangements. ISL83385ECA is functionally close but requires package and pinout verification before substitution. For an existing MAX3385ECAP PCB, treat any replacement as a redesign candidate unless its datasheet proves identical lead assignments, charge-pump topology, capacitor requirements, supply limits, and logic-level behavior.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Package 20-pin SSOP
Brand Analog Devices
Product Type 2/3 RS-232 transceiver
Supply Voltage Range 3.0V to 5.5V
Maximum Data Rate 250kbps
ESD Protection 15kV
Line Drivers 1 driver
Line Receivers 2 receivers
Charge Pump Dual charge pump
Charge Pump Capacitors 4 x 0.1uF at 3.3V supply
Interface True RS-232, EIA/TIA-232 and V.28/V.24
Temperature Grade Commercial

Bảo phân biệt quan trọng

  • Higher guaranteed serial throughput (vsMAX3221E)
  • Single positive supply with true RS-232 levels (vsISL83385ECA)
  • Specified ESD protection for exposed serial links (vsMAX3232E)

Ghi chú thiết kế

Place the four 0.1uF charge-pump capacitors as close as practical to their associated MAX3385ECAP pins, using short ground returns and the capacitor arrangement shown in the manufacturer datasheet. Keep the copper area beneath the capacitor network compact to limit loop inductance. Confirm that each capacitor retains the intended effective capacitance at the minimum local supply voltage and across the operating temperature range.

Separate the RS-232 driver outputs from receiver inputs and from sensitive analog or low-level digital circuits. Route the unprotected cable side toward the connector, with no unnecessary stubs or test pads in the high-impedance receiver path. Maintain a continuous ground reference beneath the interface and avoid placing the transceiver directly beneath a switching regulator or high-current inductor.

Do not assume that a similar 20-pin RS-232 transceiver is pin-compatible because its driver and receiver counts match. Verify every pin against the MAX3385E datasheet, including charge-pump capacitor pins, receiver enable or fail-safe behavior, supply pins, and ground connections. Also verify the 3.0V to 5.5V supply range, 250kbps rating, and 15kV ESD rating before releasing a substitute part into production.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The manufacturer and distributor product records do not state the requested compliance classifications. Use the current Analog Devices product documentation and quality documentation for formal environmental and material-compliance decisions.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MAX3385ECAP datasheet MAX3385ECAP datasheet pdf MAX3385ECAP pinout MAX3385ECAP specifications MAX3385ECAP 20-SSOP MAX3385ECAP 250kbps MAX3385ECAP 3.3V RS-232 MAX3385ECAP equivalent MAX3385ECAP replacement MAX3385ECAP vs ISL83385ECA MAX3385ECAP price MAX3385ECAP stock Analog Devices MAX3385ECAP MAX3385ECAP application circuit MAX3385ECAP charge pump capacitors

Các bộ phận và thuật ngữ liên quan

Analog Devices Maxim Integrated MAX3385ECAP MAX3385E MAX3221E MAX3232E MAX3241E ISL83385ECA RS-232 EIA/TIA-232 V.28/V.24 RS-232 transceiver line driver line receiver dual charge pump 15kV ESD protection 250kbps 3.0V to 5.5V supply 20-pin SSOP SSOP package family surface mount industrial RS-232 communication point-to-point serial link
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ