MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim
MPN: MAX352CPE+ ✓ Hoạt độngMAX352CPE+ Tóm tắt
An analog switch is a semiconductor device that routes analog electrical signals between input and output terminals under digital control. The MAX352 belongs to the analog switch hierarchy, where it functions as a four-channel SPST switching network. Unlike a relay or mechanical contactor, it offers compact integration, fast switching, and low off leakage, making it suitable for signals that must be switched repeatedly under digital system control.
The MAX352 series provides low on resistance below 35Ω, with channel-to-channel matching maintained within 2Ω. On-resistance remains flat over the analog signal range, with a maximum variation of 3Ω. These characteristics help reduce signal attenuation and channel-dependent errors. The normally open configuration allows each channel to remain disconnected until its corresponding control signal activates the selected path.
Each switch operates independently, enabling four separately controlled routes within one package. The MAX352 is differentiated from the MAX351 by its normally open switches, while the MAX353 combines two normally open and two normally closed channels. Switching times of 175ns and 145ns are listed for the device, supporting fast control-loop and communication-interface operation.
Typical uses include precision signal selection, sample-and-hold systems, multiplexed test paths, digital signal processing front ends, and communication equipment. The low 250pA off leakage is particularly useful when switching high-impedance sources, where unwanted leakage could create measurement errors or disturb sensitive analog nodes. The 16-pin PDIP package also supports straightforward through-hole assembly and prototyping.
Designers should verify signal amplitude, control-logic levels, maximum current, and operating temperature against the manufacturer datasheet. Keep sensitive analog traces short, provide a stable ground reference, and avoid exceeding the switch's 15V signal or supply range. The normally open topology requires deliberate control sequencing if a default isolation state is required.
This product page consolidates the MAX352 family specifications, verified source links, package information, application guidance, and compatible alternatives into an engineering-focused reference for analog signal-routing designs.
Bộ thay thế dễ dàng lắp đặt cho MAX352CPE+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX352CPE+ (cùng hình factor và footprint) — khác nhau ở Switch Configuration, Package, Number of Channels, On-Resistance.
MAX352EPE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX351EPE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX353EPE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX352CPE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG412CJ+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX352CPE+ Tỷ lệ tối đa & tính chất điện
| Number of Switches | 4 switches |
| Switch Configuration | 1:1 SPST |
| Switch State | Normally open (NO) |
| On Resistance | 35Ω maximum |
| On-Resistance Matching Between Channels | 2Ω maximum |
| On-Resistance Variation Over Analog Signal Range | 3Ω maximum |
| Off Leakage Current | 250pA |
| Switching Time | 175ns and 145ns |
| Maximum Signal or Supply Voltage | 15V |
| Hộp | 16-pin PDIP, 0.300 inch (7.62mm) pitch |
| Kiểu lắp đặt | Through-hole |
| Break-Before-Make | Supported |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Hướng dẫn cấu hình chân MAX352CPE+ 16-pin pdip, 0.300 inch (7.62mm) pitch
Cấu hình chân cho MAX352CPE+ (16-pin pdip, 0.300 inch (7.62mm) pitch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX352CPE+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX352CPE+ phù hợp cho 6 Áp dụngs: Precision Multiplexed Measurement, Data Acquisition Front End, Digital Signal Processing Routing, Test and Signal Selection, Communication Signal Routing, Sample-and-Hold Signal Selection.
Precision Multiplexed Measurement
The MAX352CPE+ fits multiplexed measurement systems because it provides four independent normally open SPST paths with on resistance below 35Ω. On-resistance matching within 2Ω and variation no greater than 3Ω across the analog range help limit channel-dependent gain error when several sensor or instrument inputs share one measurement chain. The 250pA off leakage also reduces disturbance at high-impedance sources. In a practical circuit, the four common terminals can feed a multiplexer or instrumentation block while individual normally open inputs select the source. Confirm the control thresholds and maximum switch current in the manufacturer datasheet before operating near electrical limits.
Được đề xuất
Data Acquisition Front End
The MAX352CPE+ is suitable for routing sensor outputs into a data-acquisition front end because its four normally open channels can connect one source at a time without introducing excessive channel resistance. The maximum on resistance of 35Ω is low enough for many sensor and buffered signal paths, while matching within 2Ω helps preserve consistency between successive measurements. Its listed 175ns and 145ns switching times allow fast source selection in multiplexed acquisition systems. Place the device close to the analog input routing and keep traces short to limit pickup and capacitance. Validate input bandwidth and settling behavior at the actual source impedance.
Được đề xuất
Digital Signal Processing Routing
The MAX352CPE+ can route precision analog channels entering a digital signal processing system, particularly where four controlled paths are required in a compact through-hole package. On-resistance matching within 2Ω and flatness within 3Ω help maintain similar signal attenuation across operating channels, while the 250pA off leakage limits leakage into high-impedance DSP analog inputs. The normally open topology provides a defined disconnected state before control firmware selects a source. For high-speed designs, account for switch capacitance, logic propagation delay, and amplifier settling time rather than considering only the nominal switching time.
Được đề xuất
Test and Signal Selection
The MAX352CPE+ fits test equipment that must connect several low-level nodes to a common measurement channel. Four normally open switches support independent selection of test points, and the specified 250pA off leakage is beneficial when the system monitors high-impedance nodes between measurements. The family's on-resistance matching within 2Ω reduces the need for channel-by-channel correction when similar signal amplitudes are compared. For automated test systems, choose control timing so the measurement waits for the selected switch and downstream network to settle. Verify maximum signal amplitude, current, and temperature range from the manufacturer datasheet.
Được đề xuất
Communication Signal Routing
The MAX352CPE+ can route communication signals where compact, low-leakage switching is required within a 15V signal or supply range. Its listed switching times of 175ns and 145ns support relatively quick path changes, while low on resistance limits insertion loss in moderate-impedance analog communication circuits. The normally open contacts are useful when a line should remain isolated until explicitly selected. Designers should still assess bandwidth, charge injection, off isolation, and logic compatibility for the specific line rate. Use short analog traces and a clean ground reference to preserve signal quality.
Được đề xuất
Sample-and-Hold Signal Selection
The MAX352CPE+ can select among four source paths in a sample-and-hold or switched-capacitor front end, provided the selected node amplitudes and bandwidth remain within device limits. Low off leakage of 250pA helps preserve the charge on sensitive sampling nodes when their switch is open, while on-resistance matching within 2Ω supports more uniform acquisition behavior between channels. The normally open state leaves each sampling path disconnected until the control sequence commands closure. Keep the routing network short, provide adequate settling time for the source and hold capacitor, and check control-logic polarity in the system design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX352CPE+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX352EPE | MAX351EPE | MAX353EPE | MAX352CPE | DG412CJ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Microchip Technology |
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Number of Switches | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST |
Bảo phân biệt quan trọng
- Consistent normally open behavior across all channels (vsMAX353EPE)
- Defined isolated state for high-impedance sources (vsMAX351EPE)
- Documented bipolar-family cross-reference in a PDIP-16 footprint (vsDG412CJ)
- Low on-resistance matching for precision routing (vsMAX352EPE)
Ghi chú thiết kế
Treat the MAX352 as a precision signal-routing element rather than an ideal switch. Its maximum on resistance is 35Ω, so source impedance, switch resistance, capacitance, amplifier input bias current, and downstream settling determine the practical error. For high-impedance sources, the 250pA off leakage can create an error current when multiplied by the source impedance. Confirm that leakage multiplied by the source impedance remains below the measurement resolution.
Route each analog common and switched input directly to the corresponding PDIP-16 pin, keeping traces short and away from digital clocks, relay contacts, and switching power nodes. The MAX352 operates through a 0.300-inch (7.62mm) PDIP pitch, so use a mechanically stable through-hole footprint and observe the manufacturer pin-1 orientation. Provide an uninterrupted ground reference to minimize switching transients coupled into the analog path.
Do not substitute a normally closed or mixed-state family member without checking the control behavior. MAX351 switches are normally closed, while MAX353 provides two normally open and two normally closed channels; either can appear footprint-compatible while changing the default signal path. Likewise, the MAX352EPE ordering code and DG412CJ cross-reference require verification of temperature grade, control polarity, maximum voltage, current, leakage, and timing before production use.
Although the MAX352 is designed for precision analog routing, its control transitions can inject charge into adjacent high-impedance nodes. Keep control traces away from sensitive analog inputs, use a clean return path for the digital controls, and avoid placing the switch next to uncontrolled high-slope switching circuits. In measurement systems, insert a settling delay after changing the selected path and compare results with the channel selected during the previous acquisition.
Thông tin tuân thủ
The manufacturer product page identifies the MAX352 family as production precision quad SPST analog switches, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code. AEC-Q100 is not applicable to this general-purpose interface IC.