Maxim Integrated

MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim

料号: MAX352CPE+ ✓ 量产中
15V Vdss 250pA Id 35Ω maximum Rds(on) 16-pin PDIP, 0.300 inch (7.62mm) pitch Package
最小起订量: 1 |

MAX352CPE+ 概述

Analog Devices MAX352CPE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 35Ω, and a 16-pin PDIP package. The device supports analog signal switching over a 15V range and provides low off leakage of 250pA. Its four independent switches are intended for precision routing in data acquisition, test equipment, communication systems, and signal-processing circuits.

An analog switch is a semiconductor device that routes analog electrical signals between input and output terminals under digital control. The MAX352 belongs to the analog switch hierarchy, where it functions as a four-channel SPST switching network. Unlike a relay or mechanical contactor, it offers compact integration, fast switching, and low off leakage, making it suitable for signals that must be switched repeatedly under digital system control.

The MAX352 series provides low on resistance below 35Ω, with channel-to-channel matching maintained within 2Ω. On-resistance remains flat over the analog signal range, with a maximum variation of 3Ω. These characteristics help reduce signal attenuation and channel-dependent errors. The normally open configuration allows each channel to remain disconnected until its corresponding control signal activates the selected path.

Each switch operates independently, enabling four separately controlled routes within one package. The MAX352 is differentiated from the MAX351 by its normally open switches, while the MAX353 combines two normally open and two normally closed channels. Switching times of 175ns and 145ns are listed for the device, supporting fast control-loop and communication-interface operation.

Typical uses include precision signal selection, sample-and-hold systems, multiplexed test paths, digital signal processing front ends, and communication equipment. The low 250pA off leakage is particularly useful when switching high-impedance sources, where unwanted leakage could create measurement errors or disturb sensitive analog nodes. The 16-pin PDIP package also supports straightforward through-hole assembly and prototyping.

Designers should verify signal amplitude, control-logic levels, maximum current, and operating temperature against the manufacturer datasheet. Keep sensitive analog traces short, provide a stable ground reference, and avoid exceeding the switch's 15V signal or supply range. The normally open topology requires deliberate control sequencing if a default isolation state is required.

This product page consolidates the MAX352 family specifications, verified source links, package information, application guidance, and compatible alternatives into an engineering-focused reference for analog signal-routing designs.

直接替换替代料: MAX352CPE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX352CPE+ (相同外形与封装尺寸) ——差异在于 Switch Configuration, Package, Number of Channels, On-Resistance.

Maxim Integrated
Switch Configuration: 4 x SPST
Package: 16-pin PDIP
Number of Channels: 4
对比 MAX352CPE+ →
Maxim Integrated
Switch Configuration: 1:1
Package: 16-pin PDIP
Number of Channels: 4 channels
对比 MAX352CPE+ →

MAX352EPE

✅ 直接替换
Maxim Integrated
📦 PDIP-16
Precision quad SPST analog switch · 4 circuits · 1:1 · 4 channels · Single-pole single-throw (SPST) · Normally open (NO) · 35 ohm maximum · 16-pin PDIP

联系询价

查看数据手册 →

MAX351EPE

✅ 直接替换
📦 PDIP-16
Retains the quad precision SPST and below-35Ω on-resistance family ratings, but uses four normally closed switches instead of four normally open switches.

📋 参考替代料(不在目录中)

MAX353EPE

✅ 直接替换
📦 PDIP-16
Retains the quad precision SPST and below-35Ω on-resistance family ratings, but provides two normally open and two normally closed switches rather than four normally open switches.

📋 参考替代料(不在目录中)

MAX352CPE

✅ 直接替换
📦 PDIP-16
Matches the four-channel, normally open SPST configuration and 35Ω maximum on resistance; the only identified distinction is the ordering-code suffix.

📋 参考替代料(不在目录中)

DG412CJ+

✅ 直接替换
Maxim Integrated
📦 PDIP-16
4 · 4 x SPST · 45 Ω maximum · 3 Ω maximum · Δ4 Ω maximum · 16-pin PDIP · Through-hole · Analog switch IC

联系询价

查看数据手册 →

MAX352CPE+ 最大额定值与电气特性

Number of Switches 4 switches
Switch Configuration 1:1 SPST
Switch State Normally open (NO)
On Resistance 35Ω maximum
On-Resistance Matching Between Channels 2Ω maximum
On-Resistance Variation Over Analog Signal Range 3Ω maximum
Off Leakage Current 250pA
Switching Time 175ns and 145ns
Maximum Signal or Supply Voltage 15V
封装 16-pin PDIP, 0.300 inch (7.62mm) pitch
安装类型 Through-hole
Break-Before-Make Supported
RoHS 状态 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

MAX352CPE+ 16-pin pdip, 0.300 inch (7.62mm) pitch 引脚配置指南

MAX352CPE+(16-pin pdip, 0.300 inch (7.62mm) pitch 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

MAX352CPE+ 的 16-pin pdip, 0.300 inch (7.62mm) pitch 封装引脚图

暂无详细引脚数据: MAX352CPE+.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MAX352CPE+ 适用于 6 应用s: Precision Multiplexed Measurement, Data Acquisition Front End, Digital Signal Processing Routing, Test and Signal Selection, Communication Signal Routing, Sample-and-Hold Signal Selection.

📡

Precision Multiplexed Measurement

The MAX352CPE+ fits multiplexed measurement systems because it provides four independent normally open SPST paths with on resistance below 35Ω. On-resistance matching within 2Ω and variation no greater than 3Ω across the analog range help limit channel-dependent gain error when several sensor or instrument inputs share one measurement chain. The 250pA off leakage also reduces disturbance at high-impedance sources. In a practical circuit, the four common terminals can feed a multiplexer or instrumentation block while individual normally open inputs select the source. Confirm the control thresholds and maximum switch current in the manufacturer datasheet before operating near electrical limits.

🖥️

Data Acquisition Front End

The MAX352CPE+ is suitable for routing sensor outputs into a data-acquisition front end because its four normally open channels can connect one source at a time without introducing excessive channel resistance. The maximum on resistance of 35Ω is low enough for many sensor and buffered signal paths, while matching within 2Ω helps preserve consistency between successive measurements. Its listed 175ns and 145ns switching times allow fast source selection in multiplexed acquisition systems. Place the device close to the analog input routing and keep traces short to limit pickup and capacitance. Validate input bandwidth and settling behavior at the actual source impedance.

🌐

Digital Signal Processing Routing

The MAX352CPE+ can route precision analog channels entering a digital signal processing system, particularly where four controlled paths are required in a compact through-hole package. On-resistance matching within 2Ω and flatness within 3Ω help maintain similar signal attenuation across operating channels, while the 250pA off leakage limits leakage into high-impedance DSP analog inputs. The normally open topology provides a defined disconnected state before control firmware selects a source. For high-speed designs, account for switch capacitance, logic propagation delay, and amplifier settling time rather than considering only the nominal switching time.

🧪

Test and Signal Selection

The MAX352CPE+ fits test equipment that must connect several low-level nodes to a common measurement channel. Four normally open switches support independent selection of test points, and the specified 250pA off leakage is beneficial when the system monitors high-impedance nodes between measurements. The family's on-resistance matching within 2Ω reduces the need for channel-by-channel correction when similar signal amplitudes are compared. For automated test systems, choose control timing so the measurement waits for the selected switch and downstream network to settle. Verify maximum signal amplitude, current, and temperature range from the manufacturer datasheet.

📶

Communication Signal Routing

The MAX352CPE+ can route communication signals where compact, low-leakage switching is required within a 15V signal or supply range. Its listed switching times of 175ns and 145ns support relatively quick path changes, while low on resistance limits insertion loss in moderate-impedance analog communication circuits. The normally open contacts are useful when a line should remain isolated until explicitly selected. Designers should still assess bandwidth, charge injection, off isolation, and logic compatibility for the specific line rate. Use short analog traces and a clean ground reference to preserve signal quality.

⚡

Sample-and-Hold Signal Selection

The MAX352CPE+ can select among four source paths in a sample-and-hold or switched-capacitor front end, provided the selected node amplitudes and bandwidth remain within device limits. Low off leakage of 250pA helps preserve the charge on sensitive sampling nodes when their switch is open, while on-resistance matching within 2Ω supports more uniform acquisition behavior between channels. The normally open state leaves each sampling path disconnected until the control sequence commands closure. Keep the routing network short, provide adequate settling time for the source and hold capacitor, and check control-logic polarity in the system design.

推荐产品汇总

MAX352EPE Maxim Integrated 用于: Precision Multiplexed Measurement, Digital Signal Processing Routing, Sample-and-Hold Signal Selection MAX351EPE Complementary normally closed family member 用于: Precision Multiplexed Measurement, Test and Signal Selection, Sample-and-Hold Signal Selection MAX353EPE Mixed normally open and closed family member 用于: Data Acquisition Front End, Communication Signal Routing DG412CJ Quad SPST switching alternative 用于: Data Acquisition Front End, Test and Signal Selection MAX352CPE Matching legacy ordering code 用于: Digital Signal Processing Routing, Communication Signal Routing
What is the MAX352CPE+?
The MAX352CPE+ is a precision, quad, SPST analog switch with four normally open channels. According to the Analog Devices MAX352 manufacturer datasheet, it provides on resistance below 35Ω, channel matching within 2Ω, off leakage of 250pA, and operation across a 15V signal or supply range. It is packaged in a 16-pin PDIP for through-hole PCB assembly.
How many switches does the MAX352CPE+ contain?
The MAX352CPE+ contains four independent normally open SPST switches. According to the Analog Devices MAX352 manufacturer datasheet, each channel can be controlled separately, allowing one package to route four analog signals. Its quad configuration reduces component count in multiplexers, test systems, and signal-processing circuits compared with four separate single-channel switch packages.
What is the on resistance of the MAX352CPE+?
The MAX352CPE+ has a maximum on resistance of 35Ω. According to the Analog Devices MAX352 manufacturer datasheet, on-resistance matching between channels is maintained within 2Ω, while variation over the analog signal range is no more than 3Ω. These matching and flatness characteristics help reduce channel-dependent attenuation when low-level analog signals pass through the switch.
Where can I download the MAX352CPE+ datasheet PDF?
The official MAX352CPE+ technical information is available from the Analog Devices MAX352 product page at analog.com, with the manufacturer datasheet linked from that page. The product family data sheet is identified as Data Sheet Rev. 2. Use the manufacturer PDF for authoritative pin assignments, timing limits, electrical characteristics, and ordering information.
Where can I find the MAX352CPE+ pinout?
The MAX352CPE+ pinout is defined by the 16-pin PDIP pin-description table in the Analog Devices MAX352 manufacturer datasheet. The device uses four normally open SPST switches, with the control, common, and normally open terminals assigned across the package. Assign PCB tracks directly from that table and preserve the package notch and pin-1 orientation when soldering.
Is the MAX352CPE+ a normally open or normally closed switch?
The MAX352CPE+ has four normally open switches. According to the Analog Devices MAX352 manufacturer datasheet, the MAX351 uses normally closed switches, the MAX352 uses normally open switches, and the MAX353 combines two normally open with two normally closed channels. The normally open MAX352 configuration provides a default disconnected path when its control input is inactive.
What is the difference between MAX351 and MAX352?
The principal difference is the default contact state: MAX351 has four normally closed switches, while MAX352 has four normally open switches. According to the Analog Devices MAX352 manufacturer datasheet, both belong to the precision quad SPST family with on resistance below 35Ω. Choose MAX352 when a path should remain off until commanded and MAX351 when continuity should exist before activation.
What is the difference between MAX352 and MAX353?
The MAX352 provides four normally open switches, whereas the MAX353 provides two normally open and two normally closed switches. According to the Analog Devices MAX352 manufacturer datasheet, both are precision quad SPST devices with low on resistance and controlled channel matching. The MAX352 is the better fit when every signal path requires the same default-open behavior.
When should I choose the MAX352CPE+ over the MAX351?
Choose the MAX352CPE+ when all four channels should be normally open, allowing signals to remain isolated until a control input asserts the desired path. The MAX351 is preferable when all four paths should be normally closed. According to the Analog Devices MAX352 manufacturer datasheet, the family maintains the same low on-resistance and channel-matching characteristics, so the default contact state should drive the decision.
Is the MAX352CPE+ suitable for high-impedance analog measurement?
The MAX352CPE+ can be suitable for high-impedance analog measurement because its off leakage is 250pA. According to the Analog Devices MAX352 manufacturer datasheet, the low leakage helps limit disturbance of sensitive source nodes when a channel is disconnected. Final suitability still depends on source impedance, signal bandwidth, temperature, leakage contribution from surrounding circuitry, and the measurement accuracy required.
What can replace the MAX352CPE+?
The closest documented alternatives are the MAX352EPE in the same PDIP family and the DG412CJ in a compatible 16-pin PDIP configuration. The cross-reference comparison identifies the DG412CJ as having consistent SPST functions, channels, and terminal package compatibility. A replacement should still be checked for control polarity, voltage rating, on resistance, leakage, switching time, and break-before-make behavior before production use.
Is the DG412CJ a drop-in replacement for the MAX352CPE+?
The DG412CJ is a potential drop-in replacement for the MAX352CPE+ because the published comparison identifies matching SPST functions, four channels, CMOS implementation, and a PDIP-16 footprint. However, engineers must confirm control logic, maximum voltage, on resistance, leakage, switching speed, and operating temperature in the DG412CJ manufacturer datasheet before approving it for an existing PCB.
Where can I buy the MAX352CPE+ and check the lead time?
Use the Request a Quote form on this page to ask for MAX352CPE+ availability, minimum order quantity, lead time, and a current unit quotation. The Request a Quote workflow keeps stock and delivery information aligned with current supply conditions instead of presenting a potentially stale inventory count. Include your required quantity, target package variant, and delivery location in the request.
What is the price of the MAX352CPE+?
Use the Request a Quote form on this page for the current MAX352CPE+ price and quantity schedule. Pricing can vary with order volume, delivery terms, and supply status, so a live quotation provides the most useful figure for purchasing decisions. The structured offer shown on this page is updated when qualifying current pricing is available.
Is the MAX352CPE+ in stock?
Current MAX352CPE+ inventory should be confirmed through the Request a Quote form on this page. The form accepts the required quantity and delivery information so purchasing can return a current availability response. Do not infer production readiness from a catalog listing alone; confirm allocation, lead time, and the exact 16-pin PDIP ordering code before releasing a production order.
What are the key specifications of MAX352CPE+ that engineers should know?
The key MAX352CPE+ specifications are four normally open SPST channels, maximum on resistance of 35Ω, on-resistance matching within 2Ω, maximum variation of 3Ω over the analog range, 250pA off leakage, 15V maximum signal or supply voltage, and listed switching times of 175ns and 145ns. According to the Analog Devices MAX352 manufacturer datasheet, the device is housed in a 16-pin PDIP package.

工程参考数据: MAX352CPE+ ——对比、设计指导和合规信息。

选型指南

Choose MAX352CPE+ when the design requires four independent, normally open SPST paths with on resistance below 35Ω, channel matching within 2Ω, and low off leakage of 250pA. MAX352EPE is the closest same-family alternative when its ordering-code grade better matches the production requirement, while MAX352CPE offers the matching legacy ordering form. MAX351EPE is appropriate only when normally closed behavior is wanted, and MAX353EPE when two normally open and two normally closed channels are useful. Consider DG412CJ for a documented cross-brand PDIP-16 alternative, but verify control polarity, voltage, current, leakage, timing, and temperature before substitution. For new designs, prioritize the exact required contact state and electrical limits over the suffix alone.

与替代料对比

参数 本产品 MAX352EPE MAX351EPE MAX353EPE MAX352CPE DG412CJ
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Microchip Technology
Package PDIP-16 PDIP-16 PDIP-16 PDIP-16 PDIP-16 PDIP-16
Number of Switches 4 4 4 4 4 4
Switch Configuration 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST 1:1 SPST

关键差异点

  • Consistent normally open behavior across all channels (对比 MAX353EPE)
  • Defined isolated state for high-impedance sources (对比 MAX351EPE)
  • Documented bipolar-family cross-reference in a PDIP-16 footprint (对比 DG412CJ)
  • Low on-resistance matching for precision routing (对比 MAX352EPE)

设计说明

Treat the MAX352 as a precision signal-routing element rather than an ideal switch. Its maximum on resistance is 35Ω, so source impedance, switch resistance, capacitance, amplifier input bias current, and downstream settling determine the practical error. For high-impedance sources, the 250pA off leakage can create an error current when multiplied by the source impedance. Confirm that leakage multiplied by the source impedance remains below the measurement resolution.

Route each analog common and switched input directly to the corresponding PDIP-16 pin, keeping traces short and away from digital clocks, relay contacts, and switching power nodes. The MAX352 operates through a 0.300-inch (7.62mm) PDIP pitch, so use a mechanically stable through-hole footprint and observe the manufacturer pin-1 orientation. Provide an uninterrupted ground reference to minimize switching transients coupled into the analog path.

Do not substitute a normally closed or mixed-state family member without checking the control behavior. MAX351 switches are normally closed, while MAX353 provides two normally open and two normally closed channels; either can appear footprint-compatible while changing the default signal path. Likewise, the MAX352EPE ordering code and DG412CJ cross-reference require verification of temperature grade, control polarity, maximum voltage, current, leakage, and timing before production use.

Although the MAX352 is designed for precision analog routing, its control transitions can inject charge into adjacent high-impedance nodes. Keep control traces away from sensitive analog inputs, use a clean return path for the digital controls, and avoid placing the switch next to uncontrolled high-slope switching circuits. In measurement systems, insert a settling delay after changing the selected path and compare results with the channel selected during the previous acquisition.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer product page identifies the MAX352 family as production precision quad SPST analog switches, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code. AEC-Q100 is not applicable to this general-purpose interface IC.

数据核验日期: 2026-11-18 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX352CPE+ datasheet MAX352CPE+ pinout MAX352CPE+ datasheet pdf MAX352CPE+ equivalent MAX352CPE+ replacement MAX352CPE+ drop-in replacement MAX352CPE+ vs DG412CJ MAX352CPE+ footprint MAX352CPE+ price MAX352CPE+ stock Maxim MAX352CPE+ MAX352CPE+ 35 ohm SPST MAX352CPE+ PDIP-16 pinout MAX352CPE+ analog switch application what can replace MAX352CPE+

相关元器件 & 术语

Maxim Integrated Analog Devices MAX352CPE+ MAX352EPE MAX351EPE MAX353EPE MAX352CPE DG412CJ analog switch SPST switch normally open switch interface IC semiconductor PDIP-16 DIP package through-hole package on resistance off leakage current break-before-make precision signal routing data acquisition test and measurement digital signal processing RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情