MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated
MPN: MAX397CPI+ ✓ Hoạt độngMAX397CPI+ Tóm tắt
An analog multiplexer is an analog switch network that routes a selected input channel to an output terminal under digital control. In the signal-chain hierarchy, the MAX397CPI+ is a CMOS analog switch IC, also described as a 16-channel or dual 8-channel precision multiplexer. It reduces the number of external connections required when several low-frequency analog signals must share one downstream converter, amplifier, or measurement circuit.
The MAX397CPI+ uses Maxim's low-voltage silicon-gate process to provide low on-resistance, tightly matched switch resistance, low charge injection, and fast switching. Its maximum on-resistance is 100 ohms, with matching between switches specified within 6 ohms. The on-resistance remains flat within 10 ohms over the specified signal range, helping preserve signal amplitude and accuracy when different channels are selected.
The multiplexer accepts a single supply from +2.7 V to +16 V or dual supplies from ±2.7 V to ±8 V. CMOS-compatible logic inputs simplify control from common digital systems. These supply options allow operation from low-voltage equipment as well as higher-range instrumentation while supporting bipolar signal paths when dual supplies are used.
Typical uses include battery instrumentation, data acquisition, process monitoring, automated test equipment, and mixed-signal measurement systems. The two multiplexers can monitor paired or sequential sensor channels, select test points, or route instrumentation signals while limiting the number of external converter inputs.
Design around the 100-ohm maximum on-resistance because it forms a signal-dependent voltage divider with the input and load impedances. Keep control traces away from analog inputs, use a low-impedance reference for digital controls, and observe the absolute maximum supply and signal voltages listed in the manufacturer datasheet.
This page combines the device's documented electrical characteristics, package information, supply options, pin-compatible alternatives, and practical design guidance. It also organizes purchasing questions around the Request a Quote workflow on this page so engineers can evaluate supply and procurement without relying on static price information.
Bộ thay thế dễ dàng lắp đặt cho MAX397CPI+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX397CPI+ (cùng hình factor và footprint) — khác nhau ở Process Technology, Product Type.
MAX396CPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX397EPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX306CPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX307CPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG406CPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG407CPI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX397CPI+ Thông số kỹ thuật
| Product Type | Dual 8:1 precision CMOS analog multiplexer |
| Number of Circuits | 2 circuits |
| Channel Configuration | 16-channel dual 8-channel |
| Multiplexer Ratio | 8:1 per circuit |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching | Within 6 ohms |
| On-Resistance Flatness | Within 10 ohms over the specified signal range |
| Maximum Charge Injection | 5 pC |
| ESD Protection | Greater than 2,000 V per Method 3015.7 |
| Single-Supply Voltage Range | +2.7 V to +16 V |
| Dual-Supply Voltage Range | ±2.7 V to ±8 V |
| Logic Compatibility | CMOS logic input compatible |
| Switching Performance | Fast switching |
| Process Technology | Low-voltage silicon-gate CMOS process |
| Hộp | 28-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Temperature Grade | Commercial |
Hướng dẫn cấu hình chân MAX397CPI+ 28-pin pdip
Cấu hình chân cho MAX397CPI+ (28-pin pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX397CPI+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX397CPI+ phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Acquisition, Data Acquisition Systems, Process-Control Instrumentation, Automated Test Equipment, Precision Signal Routing, Battery and Portable Instrument Control.
Battery-Powered Sensor Acquisition
The MAX397CPI+ fits battery-powered sensor acquisition because its single-supply range begins at +2.7 V and its dual 8:1 organization can select two groups of sensor channels without requiring eight separate analog converter inputs. The maximum on-resistance of 100 ohms must be considered when calculating attenuation with the sensor and load impedances. Its 5 pC maximum charge injection also helps limit address-transition pulses when sampling slowly changing sensor nodes. CMOS-compatible control inputs simplify connection to a low-voltage embedded controller.
Được đề xuất
Data Acquisition Systems
The MAX397CPI+ is useful in compact data-acquisition systems that must route multiple analog inputs to one measurement amplifier or converter. Its two 8:1 sections can handle parallel channel banks, while the 28-pin PDIP package simplifies through-hole prototyping and repair. On-resistance matching within 6 ohms helps reduce channel-dependent gain errors, and the flatness limit of 10 ohms supports consistent response across the specified signal range. Firmware must avoid sampling during select transitions because charge injection can create transient errors.
Được đề xuất
Process-Control Instrumentation
The MAX397CPI+ can route pressure, temperature, and other slow-moving process signals into a shared measurement chain. Its dual 8:1 organization reduces wiring complexity in industrial monitoring equipment, while operation from +2.7 V to +16 V supports multiple supply architectures. The maximum on-resistance of 100 ohms should be included in the input network design, particularly when driving high-impedance sensors. Use short analog traces and a solid ground-plane connection to reduce noise pickup and control-signal coupling.
Được đề xuất
Automated Test Equipment
The MAX397CPI+ is appropriate for automated test equipment that scans multiple DUT pins, test nodes, or external reference signals through a common analog front end. Two independent 8:1 networks allow paired selection for differential or complementary test paths. The documented charge injection of 5 pC maximum limits logic-induced transients, although the fixture capacitance and acquisition timing still determine the observed step disturbance. The 28-pin PDIP construction also supports fixture boards that favor through-hole assembly and serviceability.
Được đề xuất
Precision Signal Routing
The MAX397CPI+ suits precision signal-routing systems where channel consistency matters more than extremely low on-resistance. Its switches are matched within 6 ohms and maintain flatness within 10 ohms across the specified signal range, helping limit gain changes when a different input is selected. A 100-ohm maximum path resistance still creates a measurable divider with finite source and load impedances. For high-accuracy measurements, use a high-impedance buffer after the mux or include the resistance directly in gain calibration.
Được đề xuất
Battery and Portable Instrument Control
The MAX397CPI+ supports portable instrument control by accepting a +2.7 V minimum single supply and CMOS-compatible address inputs. It can select battery-cell taps, resistor-network references, or external sensor lines without multiplying the analog input count of a compact converter. The through-hole 28-pin PDIP package is practical for prototypes and repairable portable assemblies. Designers should still account for mux leakage, control-logic current, and downstream converter requirements when calculating standby power for long acquisition intervals.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX397CPI+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX396CPI | MAX397EPI | MAX306CPI | MAX307CPI | DG406CPI |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Vishay Intertechnology |
| Package | 28-pin PDIP | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin PDIP - same |
| Pin Compatibility | Reference design | Pin compatible | Pin compatible | Pin compatible | Pin compatible | Pin compatible |
Bảo phân biệt quan trọng
- Dual multiplexers in one package (vsMAX306CPI)
- Matched and flat switch resistance (vsDG406CPI)
- Low charge injection (vsDG407CPI)
- Flexible single- or dual-supply operation (vsMAX396CPI)
Ghi chú thiết kế
Include the maximum 100-ohm on-resistance when calculating channel gain. Estimated: a 100-ohm source resistance and 100-ohm mux path feeding a 10-kohm load produce an approximate 97.8% signal transfer. This calculation highlights why high-impedance buffers may be preferable when the mux is placed near a sensor rather than near the converter.
Route the multiplexed analog lines directly between the mux pins and the receiving amplifier or converter. Keep address and select traces away from high-impedance analog nodes, provide a continuous ground plane, and place supply bypassing close to the device. If the source impedance is high, minimize trace length and leakage-sensitive nodes because switching transients can be amplified downstream.
Do not treat the 5 pC maximum charge-injection figure as a guarantee that every fixture and cable arrangement produces a 5 pC error. The observed pulse also depends on source impedance, load capacitance, control edge rate, and channel voltage. Leave settling time after an address change and calibrate the complete measurement chain instead of relying only on the device specification.
The MAX397CPI+ can operate from a single +2.7 V to +16 V source or from ±2.7 V to ±8 V dual rails. Select the supply arrangement based on signal polarity, and ensure every rail remains within its specified range during startup and shutdown. CMOS-compatible controls simplify interfacing, but address and enable levels must still be checked against the actual supply voltage and controller output standards.
Thông tin tuân thủ
The MAX397CPI+ is a commercial-grade analog interface IC. No RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established from the cited product information.