Maxim Integrated

MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated

MPN: MAX397CPI+ ✓ فعال
+2.7 V to +16 V Vdss 100 ohms Rds(on) 28-pin PDIP Package
حداقل سفارش: 1 |

MAX397CPI+ نمای کلی

The Maxim Integrated MAX397CPI+ is a precision dual 8:1 CMOS analog multiplexer with a maximum on-resistance of 100 ohms, a 28-pin PDIP package, and support for single or dual supplies. The device provides 16 switch channels organized as two 8:1 muxes, with charge injection limited to 5 pC maximum and ESD protection greater than 2,000 V under Method 3015.7.

An analog multiplexer is an analog switch network that routes a selected input channel to an output terminal under digital control. In the signal-chain hierarchy, the MAX397CPI+ is a CMOS analog switch IC, also described as a 16-channel or dual 8-channel precision multiplexer. It reduces the number of external connections required when several low-frequency analog signals must share one downstream converter, amplifier, or measurement circuit.

The MAX397CPI+ uses Maxim's low-voltage silicon-gate process to provide low on-resistance, tightly matched switch resistance, low charge injection, and fast switching. Its maximum on-resistance is 100 ohms, with matching between switches specified within 6 ohms. The on-resistance remains flat within 10 ohms over the specified signal range, helping preserve signal amplitude and accuracy when different channels are selected.

The multiplexer accepts a single supply from +2.7 V to +16 V or dual supplies from ±2.7 V to ±8 V. CMOS-compatible logic inputs simplify control from common digital systems. These supply options allow operation from low-voltage equipment as well as higher-range instrumentation while supporting bipolar signal paths when dual supplies are used.

Typical uses include battery instrumentation, data acquisition, process monitoring, automated test equipment, and mixed-signal measurement systems. The two multiplexers can monitor paired or sequential sensor channels, select test points, or route instrumentation signals while limiting the number of external converter inputs.

Design around the 100-ohm maximum on-resistance because it forms a signal-dependent voltage divider with the input and load impedances. Keep control traces away from analog inputs, use a low-impedance reference for digital controls, and observe the absolute maximum supply and signal voltages listed in the manufacturer datasheet.

This page combines the device's documented electrical characteristics, package information, supply options, pin-compatible alternatives, and practical design guidance. It also organizes purchasing questions around the Request a Quote workflow on this page so engineers can evaluate supply and procurement without relying on static price information.

جایگزین‌های drop-in برای MAX397CPI+ — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای MAX397CPI+ (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Process Technology, Product Type.

Analog Devices
Process Technology: Low-voltage silicon-gate CMOS
Product Type: 1-circuit 16:1 analog multiplexer
مقایسه با MAX397CPI+ →

MAX396CPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Same MAX396/MAX397 28-pin family and documented pin compatibility; channel-function details should be confirmed in the ordering table.

📋 جایگزین مرجع (خارج از کاتالوگ)

MAX397EPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Same MAX397 family and 100-ohm maximum on-resistance class; exact temperature and orderable-suffix differences require datasheet review.

📋 جایگزین مرجع (خارج از کاتالوگ)

MAX306CPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Identified as pin compatible with MAX397CPI; on-resistance and switching characteristics are 10% or less different at the family comparison level.

📋 جایگزین مرجع (خارج از کاتالوگ)

MAX307CPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Identified as pin compatible with MAX397CPI; the dual 8:1 topology preserves the core multiplexing arrangement.

📋 جایگزین مرجع (خارج از کاتالوگ)

DG406CPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Industry-standard pin-compatible 8:1 mux; maximum on-resistance differs from the MAX397CPI's 100-ohm value and must be checked for signal-loss tolerance.

📋 جایگزین مرجع (خارج از کاتالوگ)

DG407CPI

✅ جایگزین مستقیم
📦 28-pin PDIP
Industry-standard pin-compatible 8:1 mux; maximum on-resistance differs from the MAX397CPI's 100-ohm value and must be checked for signal-loss tolerance.

📋 جایگزین مرجع (خارج از کاتالوگ)

MAX397CPI+ مشخصات

Product Type Dual 8:1 precision CMOS analog multiplexer
Number of Circuits 2 circuits
Channel Configuration 16-channel dual 8-channel
Multiplexer Ratio 8:1 per circuit
Maximum On-Resistance 100 ohms
On-Resistance Matching Within 6 ohms
On-Resistance Flatness Within 10 ohms over the specified signal range
Maximum Charge Injection 5 pC
ESD Protection Greater than 2,000 V per Method 3015.7
Single-Supply Voltage Range +2.7 V to +16 V
Dual-Supply Voltage Range ±2.7 V to ±8 V
Logic Compatibility CMOS logic input compatible
Switching Performance Fast switching
Process Technology Low-voltage silicon-gate CMOS process
بسته‌بندی 28-pin PDIP
نوع نصب Through-hole
Temperature Grade Commercial

راهنمای پیکربندی پین MAX397CPI+ 28-pin pdip

پیکربندی پین برای MAX397CPI+ (پکیج 28-pin pdip). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 28-pin pdip برای MAX397CPI+

داده پین‌آوت تفصیلی موجود نیست برای MAX397CPI+.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

MAX397CPI+ مناسب است برای 6 کاربردs: Battery-Powered Sensor Acquisition, Data Acquisition Systems, Process-Control Instrumentation, Automated Test Equipment, Precision Signal Routing, Battery and Portable Instrument Control.

🔋

Battery-Powered Sensor Acquisition

The MAX397CPI+ fits battery-powered sensor acquisition because its single-supply range begins at +2.7 V and its dual 8:1 organization can select two groups of sensor channels without requiring eight separate analog converter inputs. The maximum on-resistance of 100 ohms must be considered when calculating attenuation with the sensor and load impedances. Its 5 pC maximum charge injection also helps limit address-transition pulses when sampling slowly changing sensor nodes. CMOS-compatible control inputs simplify connection to a low-voltage embedded controller.

📊

Data Acquisition Systems

The MAX397CPI+ is useful in compact data-acquisition systems that must route multiple analog inputs to one measurement amplifier or converter. Its two 8:1 sections can handle parallel channel banks, while the 28-pin PDIP package simplifies through-hole prototyping and repair. On-resistance matching within 6 ohms helps reduce channel-dependent gain errors, and the flatness limit of 10 ohms supports consistent response across the specified signal range. Firmware must avoid sampling during select transitions because charge injection can create transient errors.

🏭

Process-Control Instrumentation

The MAX397CPI+ can route pressure, temperature, and other slow-moving process signals into a shared measurement chain. Its dual 8:1 organization reduces wiring complexity in industrial monitoring equipment, while operation from +2.7 V to +16 V supports multiple supply architectures. The maximum on-resistance of 100 ohms should be included in the input network design, particularly when driving high-impedance sensors. Use short analog traces and a solid ground-plane connection to reduce noise pickup and control-signal coupling.

🧪

Automated Test Equipment

The MAX397CPI+ is appropriate for automated test equipment that scans multiple DUT pins, test nodes, or external reference signals through a common analog front end. Two independent 8:1 networks allow paired selection for differential or complementary test paths. The documented charge injection of 5 pC maximum limits logic-induced transients, although the fixture capacitance and acquisition timing still determine the observed step disturbance. The 28-pin PDIP construction also supports fixture boards that favor through-hole assembly and serviceability.

🎯

Precision Signal Routing

The MAX397CPI+ suits precision signal-routing systems where channel consistency matters more than extremely low on-resistance. Its switches are matched within 6 ohms and maintain flatness within 10 ohms across the specified signal range, helping limit gain changes when a different input is selected. A 100-ohm maximum path resistance still creates a measurable divider with finite source and load impedances. For high-accuracy measurements, use a high-impedance buffer after the mux or include the resistance directly in gain calibration.

📱

Battery and Portable Instrument Control

The MAX397CPI+ supports portable instrument control by accepting a +2.7 V minimum single supply and CMOS-compatible address inputs. It can select battery-cell taps, resistor-network references, or external sensor lines without multiplying the analog input count of a compact converter. The through-hole 28-pin PDIP package is practical for prototypes and repairable portable assemblies. Designers should still account for mux leakage, control-logic current, and downstream converter requirements when calculating standby power for long acquisition intervals.

خلاصه محصولات پیشنهادی

MAX397EPI Same-family pin-compatible multiplex option استفاده‌شده در: Battery-Powered Sensor Acquisition, Process-Control Instrumentation, Precision Signal Routing MAX396CPI Related MAX396/MAX397 precision mux استفاده‌شده در: Battery-Powered Sensor Acquisition, Automated Test Equipment MAX306CPI Pin-compatible precision multiplexer استفاده‌شده در: Data Acquisition Systems, Battery and Portable Instrument Control MAX307CPI Pin-compatible dual analog multiplexer استفاده‌شده در: Data Acquisition Systems, Precision Signal Routing DG406CPI Pin-compatible 8:1 multiplexer option استفاده‌شده در: Process-Control Instrumentation, Battery and Portable Instrument Control DG407CPI Industry pin-compatible scan multiplexer استفاده‌شده در: Automated Test Equipment
What is the MAX397CPI+?
The MAX397CPI+ is a precision dual 8:1 CMOS analog multiplexer with 16 switch channels, a maximum on-resistance of 100 ohms, and a 28-pin PDIP package. According to the Maxim Integrated datasheet, it uses a low-voltage silicon-gate process and provides charge injection of 5 pC maximum. The two independent 8:1 circuits can route paired analog signals through a shared downstream amplifier, converter, or measurement channel.
What is the operating voltage of MAX397CPI+?
The MAX397CPI+ operates from +2.7 V to +16 V with a single supply or from ±2.7 V to ±8 V with dual supplies. According to the Maxim Integrated datasheet, the multiplexer retains CMOS-compatible logic inputs under either supply arrangement. Single-supply operation is appropriate for unipolar systems, while the dual-supply range permits bipolar analog signals when the circuit and signal amplitudes remain within the specified limits.
What is the on-resistance of MAX397CPI+?
The MAX397CPI+ has a maximum on-resistance of 100 ohms, with resistance matched within 6 ohms between switches. According to the Maxim Integrated datasheet, the on-resistance also remains flat within 10 ohms over the specified signal range. This flatness helps limit channel-to-channel amplitude variation, although the 100-ohm path must be included in the source and load impedance calculation.
How much charge injection does MAX397CPI+ produce?
The MAX397CPI+ limits charge injection to 5 pC maximum. According to the Maxim Integrated datasheet, the low-voltage silicon-gate process and circuit improvements produce this low injected-charge figure. Charge injection appears as a transient when the address or select logic changes, making the device useful for instrumentation and sampled-data systems where control transitions must not create excessive signal pulses.
What is the difference between MAX397CPI+ and MAX396CPI?
The MAX397CPI+ and MAX396CPI belong to the same MAX396/MAX397 precision low-voltage CMOS multiplexer family and are identified as pin compatible. According to manufacturer-family information, both provide dual 8:1 switching, 100-ohm maximum on-resistance, low charge injection, and single- or dual-supply operation. Choose the exact orderable suffix after checking the manufacturer's complete pin and performance tables for the intended channel configuration.
Can MAX397EPI replace MAX397CPI+ on the same PCB?
MAX397EPI is identified as a pin-compatible alternative to MAX397CPI+, and both are associated with the 28-pin PDIP MAX397 family. The family specifications include a 100-ohm maximum on-resistance, matching within 6 ohms, and low leakage over temperature. Confirm the exact enable, address, and supply pin assignments in the manufacturer datasheet before production use, especially when operating near absolute-maximum conditions.
Are MAX397CPI+ and DG406 or DG407 pin-compatible?
The MAX397CPI family is identified as pin compatible with industry-standard MAX306, MAX307, DG406, DG407, DG506A, and DG507A devices. According to the family cross-reference information, this compatibility enables evaluation of established multiplexers without changing the PCB land pattern. Verify electrical details such as on-resistance, logic levels, supply polarity, and switching timing against the requirements of the original design.
When should I choose MAX397CPI+ instead of MAX396CPI?
Choose MAX397CPI+ when the design requires the MAX397 family's dual 8:1 precision multiplexing and its documented low-voltage CMOS behavior. The MAX396CPI is a closely related family member with the same 28-pin heritage and is identified as pin compatible. Final selection should follow the complete manufacturer ordering table, particularly if the design depends on a specific address truth table, enable polarity, temperature grade, or operating-limit detail.
What is the best drop-in replacement for MAX397CPI+?
MAX397EPI is the closest documented same-family candidate for MAX397CPI+, while MAX396CPI, MAX306CPI, MAX307CPI, DG406CPI, and DG407CPI are identified as pin-compatible industry alternatives. The replacement should be selected only after checking its exact 28-pin pinout, supply range, logic thresholds, on-resistance, leakage, and switching specifications. The Request a Quote form on this page can be used to discuss availability and lifecycle requirements.
What Maxim Integrated or Vishay equivalent works with MAX397CPI+?
MAX397EPI is a Maxim Integrated same-family candidate, while MAX396CPI, MAX306CPI, and MAX307CPI are Maxim devices identified as pin compatible with MAX397CPI. Vishay Intertechnology's DG406CPI and DG407CPI are also identified as industry-standard pin-compatible choices. Each candidate should be checked against the original circuit's exact logic levels, supply arrangement, and analog performance requirements before substitution.
Where can I download the MAX397CPI+ datasheet PDF?
The MAX397CPI+ datasheet PDF is available through the manufacturer datasheet link on this page, with an additional archived PDF copy linked in the product documentation. The document describes the MAX396/MAX397 family, including the 100-ohm maximum on-resistance, 5 pC maximum charge injection, supply ranges, ESD rating, and application information. Use the pin-description table and ordering information in that document for final PCB and purchasing decisions.
Where can I find the MAX397CPI+ pinout?
The MAX397CPI+ pinout is documented in the manufacturer datasheet's pin-description section for the 28-pin PDIP package. Use the package drawing to identify pin 1, address inputs, select controls, analog terminals, supply pins, and ground connections. The archived datasheet linked on this page is a practical starting point, but the manufacturer pin table should remain the authority for board layout and replacement qualification.
How should I calculate signal error for MAX397CPI+?
Calculate the channel error by treating the 100-ohm maximum on-resistance as a series resistance between the source and the multiplexer output. Estimated: with a source impedance of 100 ohms and a 10-kohm load, the worst-case voltage-divider ratio is approximately 10,000 divided by 10,200, or about 98%. This is an engineering estimate; actual channel error also depends on leakage, switch resistance variation, signal amplitude, and the selected load.
Is MAX397CPI+ suitable for battery-powered measurement systems?
The MAX397CPI+ is suitable for many battery-powered measurement systems because its single-supply operating range starts at +2.7 V and its CMOS-compatible controls support common low-voltage digital systems. Its dual 8:1 organization reduces the number of analog converter inputs required in many sensor arrangements. Power budget and leakage should still be evaluated because the complete system may spend substantial time between measurements.
How do I design PCB layout around MAX397CPI+?
Place the MAX397CPI+ close to the signals it routes and keep multiplexed analog traces short and separated from address and select traces. Provide a low-impedance ground reference and route supply connections directly to the relevant pins. Avoid long traces adjacent to high-impedance sensor nodes because capacitive coupling from address transitions can create errors greater than the small documented charge-injection specification.

داده‌های مرجع مهندسی برای MAX397CPI+ — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose MAX397CPI+ when the design needs two precision 8:1 analog multiplexers in a 28-pin PDIP footprint, low-voltage operation, and documented low charge injection. MAX397EPI is the closest same-family candidate for a second-source evaluation, while MAX396CPI is appropriate when the MAX396 family configuration satisfies the address truth table and application. MAX306CPI and MAX307CPI can be considered for pin-compatible industry-standard mux designs after checking on-resistance, leakage, logic levels, and switching timing. DG406CPI and DG407CPI are useful cross-brand candidates when their electrical characteristics meet the signal-loss budget. In every case, verify the 28-pin assignment, absolute maximum ratings, supply polarity, and enable behavior against the manufacturer datasheet. For high-accuracy measurements, include the switch resistance in gain calculations and allow adequate settling time after each address transition.

مقایسه با جایگزین‌ها

پارامتر این محصول MAX396CPI MAX397EPI MAX306CPI MAX307CPI DG406CPI
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Vishay Intertechnology
Package 28-pin PDIP 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same
Pin Compatibility Reference design Pin compatible Pin compatible Pin compatible Pin compatible Pin compatible

تفاوت‌های کلیدی

  • Dual multiplexers in one package (در مقابلMAX306CPI)
  • Matched and flat switch resistance (در مقابلDG406CPI)
  • Low charge injection (در مقابلDG407CPI)
  • Flexible single- or dual-supply operation (در مقابلMAX396CPI)

یادداشت‌های طراحی

Include the maximum 100-ohm on-resistance when calculating channel gain. Estimated: a 100-ohm source resistance and 100-ohm mux path feeding a 10-kohm load produce an approximate 97.8% signal transfer. This calculation highlights why high-impedance buffers may be preferable when the mux is placed near a sensor rather than near the converter.

Route the multiplexed analog lines directly between the mux pins and the receiving amplifier or converter. Keep address and select traces away from high-impedance analog nodes, provide a continuous ground plane, and place supply bypassing close to the device. If the source impedance is high, minimize trace length and leakage-sensitive nodes because switching transients can be amplified downstream.

Do not treat the 5 pC maximum charge-injection figure as a guarantee that every fixture and cable arrangement produces a 5 pC error. The observed pulse also depends on source impedance, load capacitance, control edge rate, and channel voltage. Leave settling time after an address change and calibrate the complete measurement chain instead of relying only on the device specification.

The MAX397CPI+ can operate from a single +2.7 V to +16 V source or from ±2.7 V to ±8 V dual rails. Select the supply arrangement based on signal polarity, and ensure every rail remains within its specified range during startup and shutdown. CMOS-compatible controls simplify interfacing, but address and enable levels must still be checked against the actual supply voltage and controller output standards.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The MAX397CPI+ is a commercial-grade analog interface IC. No RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established from the cited product information.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

MAX397CPI+ datasheet MAX397CPI+ datasheet pdf MAX397CPI+ pinout MAX397CPI+ specifications Maxim Integrated MAX397CPI+ MAX397CPI+ equivalent MAX397CPI+ replacement MAX397CPI+ cross reference MAX397CPI+ 28-PDIP MAX397CPI+ 100 ohm on resistance MAX397CPI+ vs MAX397EPI MAX397CPI+ price MAX397CPI+ stock MAX397CPI+ data acquisition MAX397CPI+ analog multiplexer

قطعات و اصطلاحات مرتبط

Maxim Integrated MAX397CPI+ MAX396CPI MAX397EPI MAX306CPI MAX307CPI DG406CPI DG407CPI Vishay Intertechnology analog multiplexer analog switch IC CMOS multiplexer precision multiplexer dual 8:1 multiplexer 16-channel multiplexer 28-pin PDIP DIP package family through-hole package surface-mount alternative on-resistance charge injection ESD protection single-supply operation dual-supply operation CMOS logic data acquisition
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ