MAX456EPL+ - 8x8 35MHz Video Crosspoint Switch | Analog Devices
MPN: MAX456EPL+ ✓ Hoạt độngMAX456EPL+ Tóm tắt
A video crosspoint switch is an interface IC that provides configurable signal paths between multiple source and destination channels. Within the broader signal-chain hierarchy, the MAX456 belongs to video switches, analog multiplexers, interface ICs, and semiconductors. Unlike a simple mechanical video switch, a crosspoint matrix can route many source signals to selected destinations electronically while reducing the component count, board area, and external interconnection complexity of a conventional relay-based matrix.
The MAX456 integrates eight video inputs and eight outputs in one monolithic CMOS device. Its stated 35 MHz bandwidth supports baseband analog video signals, including composite video and other bandwidth-compatible analog sources. Independent matrix control allows operators or system logic to change routing configurations without physically reconnecting cables. The MAX456EPL+ is identified as an industrial-grade 40-pin PDIP version, supporting through-hole PCB assembly and conventional socket-compatible prototyping workflows.
Because the MAX456 is an analog video crosspoint rather than a modern digital video processor, its useful design limits are defined by analog bandwidth, channel isolation, gain behavior, crosstalk, power requirements, and output drive. Those detailed electrical characteristics should be checked in the manufacturer datasheet before cascading multiple devices or driving long cable runs. The monolithic architecture can simplify a matrix implementation, but it does not eliminate the need for source termination, grounding, decoupling, and controlled impedance routing.
Typical uses include television studio routing, CCTV control-room matrices, lecture-capture video distribution, analog video test equipment, and educational video laboratories. The 40-pin PDIP package is particularly useful where field replacement, socket use, or through-hole assembly has greater value than the smaller footprint of a surface-mount option. A one-channel signal can be routed among outputs by configuring the matrix, while full operation permits many simultaneous connections according to the switching commands supplied by the controlling electronics.
The main layout consideration is analog signal integrity. Keep video traces short, maintain a continuous ground reference, decouple supply pins near the device, and avoid routing high-speed digital control or switching-node currents beneath sensitive video paths. Because the MAX456EPL+ is a through-hole device, also plan the connector orientation and analog ground strategy before fabrication. This page consolidates the device identity, package information, design guidance, application fit, and documented same-family alternative for engineers evaluating the legacy 8 x 8 video matrix.
For new designs, verify lifecycle availability, electrical limits, and required switching logic before committing the 40-pin PDIP footprint. Request a Quote through the form on this page for current commercial conditions, and consult the manufacturer datasheet for the definitive pin description, timing, power, and analog performance tables.
Bộ thay thế dễ dàng lắp đặt cho MAX456EPL+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX456EPL+ (cùng hình factor và footprint) — khác nhau ở Temperature Grade.
MAX456CPL+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX456EPL+ Tỷ lệ tối đa & tính chất điện
| Product Type | 8 x 8 video crosspoint switch |
| Architecture | Monolithic CMOS |
| Number of Inputs | 8 video inputs |
| Số lượng đầu ra | 8 video outputs |
| Video Bandwidth | 35 MHz |
| Signal Type | Analog video |
| Hộp | 40-pin PDIP |
| Terminal Count | 40 terminals |
| Package Shape | Rectangular PDIP |
| Mounting Method | Through-hole |
| Temperature Grade | Industrial |
| Technology | CMOS |
Hướng dẫn cấu hình chân MAX456EPL+ rectangular pdip
Cấu hình chân cho MAX456EPL+ (rectangular pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX456EPL+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX456EPL+ phù hợp cho 6 Áp dụngs: Broadcast Video Routing Matrix, CCTV Surveillance Control Room, Video Test and Training Lab, Lecture Capture Video Distribution, Industrial Video Inspection Cell, Analog Video Distribution Wall.
Broadcast Video Routing Matrix
The MAX456EPL+ fits professional analog video routing because its 8 x 8 matrix connects eight video sources to eight destinations under logic control, while its 35 MHz bandwidth covers baseband composite-video requirements. It can replace a much larger collection of mechanical switches and their associated wiring. In a studio or edit-system installation, place the IC near the signal backplane, terminate each source correctly, and preserve a low-impedance ground reference between equipment racks. The principal trade-off is that this is an older analog crosspoint rather than a digital matrix, so modern HD or 4K workflows may require conversion ahead of the switching stage.
CCTV Surveillance Control Room
An eight-input, eight-output analog surveillance installation can use the MAX456EPL+ to let an operator select which camera feeds appear at multiple monitoring positions. The 8 x 8 topology provides flexible routing without changing every cable whenever a display assignment changes, and the 35 MHz bandwidth is suitable for compatible baseband video signals. Keep camera coax connections and ground paths separated from digital control wiring, terminate unused outputs as required by the system architecture, and verify cable attenuation before expecting the switch bandwidth to translate into acceptable image quality at long cable lengths.
Video Test and Training Lab
The MAX456EPL+ is useful in an analog video laboratory where several camera, pattern-generator, and playback sources must be routed to instruments or training displays. Its programmable matrix simplifies repeatable signal-path demonstrations without manually moving cables, and the through-hole PDIP package supports socketed laboratory boards. Because the device is a legacy analog crosspoint, create clearly labeled test channels and document the supported signal format, source impedance, and bandwidth. Adding buffering or line drivers may be necessary when long cables or multiple destination loads exceed the practical drive capability of the switching network.
Lecture Capture Video Distribution
A lecture-capture system can route a podium camera, document camera, room overview camera, and computer video source among recorders, projectors, and confidence monitors by using the MAX456EPL+ as an 8 x 8 analog matrix. Its multiple simultaneous routing paths make it more flexible than a simple single-input selector. Keep the video path isolated from power-converter and display-backlight switching circuits, maintain short ground returns, and ensure every connected source uses compatible amplitude and impedance. If the installation includes digital classroom capture, the switching point remains most useful for legacy composite analog sources rather than modern packetized video links.
Industrial Video Inspection Cell
Machine-vision monitoring can benefit from the MAX456EPL+ when several analog inspection cameras must be routed to displays, recorders, or vision interfaces. The matrix provides eight source channels and eight destination channels, while the 35 MHz specification supports bandwidth-compatible baseband video. Industrial cabinets can introduce electrical noise, ground potential differences, and long cable runs, so use shielded coax, maintain controlled grounding, and place decoupling close to the IC. Verify camera synchronization and signal-level requirements separately because the crosspoint configuration does not imply frame synchronization or isolation from every camera system.
Analog Video Distribution Wall
The MAX456EPL+ can form the central routing element of a small analog distribution wall serving several monitors, recorders, and confidence displays. Eight programmable outputs make it possible to direct the same source to multiple destinations while maintaining flexible control over the visible layout. Route outputs according to the manufacturer loading recommendations and use suitable distribution buffering where output loading or cable loss is significant. The 40-pin PDIP construction is advantageous for repairable equipment, but the board should provide ample component spacing and mechanical clearance for reliable through-hole soldering and socket use.
Dữ liệu tham khảo kỹ thuật cho MAX456EPL+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX456CPL+ |
|---|---|---|
| Manufacturer | Maxim Integrated | Maxim Integrated |
| Product Type | 8 x 8 video crosspoint switch | MAX456-series video crosspoint switch |
| Package | 40-pin PDIP | 40-pin PDIP - same |
| Input Channels | 8 video inputs | 8 video inputs |
| Output Channels | 8 video outputs | 8 video outputs |
| Video Bandwidth | 35 MHz | 35 MHz |
| Architecture | Monolithic CMOS | Monolithic CMOS |
| Mounting Method | Through-hole | Through-hole |
Bảo phân biệt quan trọng
- Single-chip 8 x 8 routing matrix (vsMAX456CPL+)
- 35 MHz analog video bandwidth (vsMAX456CPL+)
- Repairable through-hole implementation (vsMAX456CPL+)
Ghi chú thiết kế
Treat the video nets as sensitive analog paths: use a continuous ground plane, avoid long parallel runs with switching or digital return currents, and keep control traces away from input and output pins. Place the IC near the matrix connector or source interface so unnecessary loop area is minimized. For a 40-pin through-hole design, verify connector orientation against the package drawing before routing the first PCB revision.
Confirm source impedance, output loading, insertion loss, and cable attenuation before assigning all eight channels. The stated 35 MHz bandwidth is the device bandwidth, not a guarantee of acceptable signal quality for every source or cable combination. Use proper source termination and follow the recommended output-loading conditions in the manufacturer datasheet; add a line driver or distribution amplifier when long cables or multiple loads would otherwise degrade the signal.
Provide stable supply bypassing at the IC and decouple the analog and control sections according to the manufacturer application circuit. Keep switching-regulator and converter currents physically separated from the video path, and observe each supply pin's voltage limits and sequencing requirements. Because detailed current consumption is not listed in the component summaries, obtain the electrical tables before sizing the regulator or calculating thermal dissipation.
Do not treat a shared family name as proof of drop-in equivalence. MAX456CPL+ appears in a direct comparison with MAX456EPL+, but the C and E suffix codes must be checked for temperature grade, commercial status, and electrical differences. Also confirm that the package has 40 pins in the required PDIP format and that every control, supply, ground, input, and output connection is assigned from the numbered datasheet diagram.
Thông tin tuân thủ
The component summaries do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is an industrial analog interface IC rather than an automotive-qualified device.