MC14053BD - Triple 2:1 Analog Multiplexer | onsemi
MPN: MC14053BD ✓ Hoạt độngMC14053BD Tóm tắt
An analog multiplexer is a semiconductor switching device that connects one of several signal terminals to a common terminal. The MC14053B family provides three independent 2:1 selections, allowing multiple analog sources to be routed through one shared signal path. Digital select inputs determine which source or destination is connected, while the analog switches provide bidirectional signal paths suitable for multiplexed and demultiplexed operation.
Key features include three independently controlled 2:1 analog switches, 280 ohm on-state resistance, operation over a 3.0 V to 18 V analog voltage range, and a 16-SOIC package. The manufacturer also identifies low-noise performance of 12 nV per square-root-hertz for frequencies up to 1.0 kHz. These characteristics make the device useful for sensor selection, measurement routing, signal conditioning, test systems, and other applications requiring controlled analog-channel access.
The MC14053B is part of the CMOS logic family of analog switches. Its digital control architecture allows a microcontroller or logic controller to select among signal paths without changing the physical routing of the analog network. Because the device is bidirectional, the same switching network can support multiplexing, demultiplexing, signal swapping, and routing functions depending on the external circuit configuration.
Typical applications include multiplexed sensor interfaces, instrumentation signal routing, data acquisition systems, communication equipment, and industrial control modules. In a sensor interface, the select lines can choose among several inputs before amplification or conversion. In a data acquisition circuit, separate control logic can direct different sources to a shared analog front end while minimizing the number of separate signal-chain channels.
Designers should confirm the actual pinout, control truth table, supply limits, and input voltage limits in the manufacturer datasheet before layout. The unused selector and signal terminals should be handled according to the datasheet guidance, and the common analog path should be kept away from switching nodes and high-current return paths to reduce coupling and crosstalk.
This page consolidates the manufacturer product information, package identification, channel configuration, on-state resistance, supported voltage range, and low-noise figure into a practical reference for engineers selecting an analog multiplexer. It also distinguishes device-level switching facts from parameters that must be confirmed directly from the datasheet.
Bộ thay thế dễ dàng lắp đặt cho MC14053BD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC14053BD (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, On-State Resistance, Product Type, Switch Configuration.
MC14053BF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC14053BFG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
NLV14053BDR2G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
NLV14053BDG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CD4053BE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC14053BD Thông số kỹ thuật
| Product Type | Triple 2:1 analog multiplexer/demultiplexer |
| Number of Circuits | 3 circuits |
| Switch Configuration | 2:1 |
| On-State Resistance | 280 ohm |
| Analog Voltage Range | 3.0 V to 18 V |
| VEE Constraint | VEE must be less than or equal to VSS |
| Low-Noise Performance | 12 nV/sqrt(Cycle) at f <= 1.0 kHz |
| Hộp | 16-SOIC |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
| Logic Family | CMOS |
| Signal Path Direction | Bidirectional |
| Multiplexer Channels | 3 |
| Select Ratio | 2:1 |
Cấu hình chân MC14053BD
| Chân 1 | [DATA_NEEDED: pin 1 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 2 | [DATA_NEEDED: pin 2 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 3 | [DATA_NEEDED: pin 3 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 4 | [DATA_NEEDED: pin 4 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 5 | [DATA_NEEDED: pin 5 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 6 | [DATA_NEEDED: pin 6 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 7 | [DATA_NEEDED: pin 7 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 8 | [DATA_NEEDED: pin 8 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 9 | [DATA_NEEDED: pin 9 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 10 | [DATA_NEEDED: pin 10 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 11 | [DATA_NEEDED: pin 11 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 12 | [DATA_NEEDED: pin 12 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 13 | [DATA_NEEDED: pin 13 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 14 | [DATA_NEEDED: pin 14 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 15 | [DATA_NEEDED: pin 15 name] — Use the manufacturer pin-description table for the authoritative assignment. |
| Chân 16 | [DATA_NEEDED: pin 16 name] — Use the manufacturer pin-description table for the authoritative assignment. |
Ứng dụng tiêu biểu
MC14053BD phù hợp cho 6 Áp dụngs: Multiplexed Sensor Interface, Data Acquisition Signal Router, Instrumentation Amplifier Signal Selection, Signal Swapping and Test Routing, Communication Equipment Analog Routing, Industrial Control Module.
Multiplexed Sensor Interface
The MC14053BD fits a sensor-selection front end that must combine several analog inputs before amplification or conversion. Its three independently addressed 2:1 sections allow a controller to select among paired sensor outputs and route the selected signal to a shared analog front end. The listed 280 ohm on-state resistance must be included when checking source impedance and converter settling behavior. Because the switch paths are bidirectional, the same architecture can also route a calibration signal back into the sensor node. Digital select lines should be driven from a controller with levels compatible with the MC14053B control inputs.
Được đề xuất
Data Acquisition Signal Router
MC14053BD can reduce analog front-end duplication in a data-acquisition system by selecting among multiple sensor or instrument outputs. Each 2:1 section routes one of two inputs to a shared channel, and the three sections can support several independent measurement selections. The 3.0 V to 18 V analog range accommodates conventional low-voltage measurement signals, while the 280 ohm on-state resistance needs to be checked against the source impedance and downstream converter input. Place the selected signal path away from digital clocks and provide a stable return path to minimize crosstalk.
Được đề xuất
Instrumentation Amplifier Signal Selection
The MC14053BD is useful when several conditioned instrumentation signals must feed one higher-precision amplifier or analog-to-digital converter. Three 2:1 switch sections can select among sensor, reference, or calibration inputs without requiring a separate amplifier channel for every source. The device's 12 nV per square-root-hertz family noise figure at frequencies up to 1.0 kHz supports low-noise routing, while its 280 ohm on-state resistance contributes to source impedance and should be evaluated with the amplifier input network. A high-impedance buffer may be required when the downstream stage cannot tolerate added loading.
Được đề xuất
Signal Swapping and Test Routing
MC14053BD can implement bidirectional signal swapping in test and conditioning circuits where a controller must alternate between two paths without mechanically changing the connection. Because each section contains two selectable terminals and a common terminal, the device can support routing, swapping, and demultiplexing arrangements depending on the external wiring. The manufacturer identifies a 3.0 V to 18 V analog range and 280 ohm on-state resistance. Test engineers should include the switch resistance in the expected insertion loss and account for control timing when sequencing measurements.
Được đề xuất
Communication Equipment Analog Routing
MC14053BD can route low-frequency analog paths within communication equipment when several sources need access to a shared receive or transmit chain. The three independent 2:1 sections provide flexible channel selection under digital control, while the 280 ohm on-state resistance makes it particularly relevant to high-impedance signal paths rather than low-ohm power routing. Designers should check the datasheet for operating voltage, logic thresholds, switching time, and leakage at the intended signal frequency. Shield or guard the common path if switching transients could disturb adjacent communication channels.
Được đề xuất
Industrial Control Module
MC14053BD can support analog channel selection in an industrial control module that accepts references, feedback signals, or sensor outputs from several external sources. Its three 2:1 sections allow the controller to share one conditioning path, reducing the number of discrete analog routes. The supported 3.0 V to 18 V analog range covers common control-system signal levels, and the family is identified as Pb-free packaged. Engineers should still confirm the exact operating temperature, supply configuration, and qualification requirements for the selected ordering code before using the part in an industrial installation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC14053BD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC14053BF | MC14053BFG | NLV14053BDR2G | NLV14053BDG | CD4053B |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | onsemi |
| Switch Configuration | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 | Triple 2:1 |
| Number of Circuits | 3 circuits | 3 circuits | 3 circuits | 3 circuits | 3 circuits | 3 circuits |
| Pin Count | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
| Special Feature | Low-noise MC14053B family | MC14053B family variant | MC14053B family variant | NLV14053B family variant | NLV14053B family variant | CD4053 family variant |
Bảo phân biệt quan trọng
- Three independently controlled routing sections in one IC (vsCD4053B)
- Documented low-noise family performance (vsMC14053BF)
- Explicit 280 ohm on-state resistance (vsNLV14053BDR2G)
Ghi chú thiết kế
Treat the selected common path as a sensitive analog node. The MC14053BD has a listed on-state resistance of 280 ohm, so source impedance, downstream input capacitance, and settling time should be evaluated together. Keep the common path away from digital select traces and high-impedance amplifier inputs. If crosstalk appears during channel changes, increase separation from switching nodes, use a ground guard where appropriate, and verify that downstream circuitry does not amplify charge-injection transients.
Do not infer the select truth table from the generic 2:1 label. Assign the select pins, common terminals, supply pins, and signal terminals directly from the manufacturer pin-description table and control truth table. Also distinguish the 3.0 V to 18 V analog voltage range from the complete supply and absolute-maximum specifications. The manufacturer notes that VEE must be no higher than VSS, so negative or unusual supply arrangements require separate verification before layout.
Place the MC14053BD close to the sources and destinations that share its analog path. Keep each analog route short and pair it with a continuous return-plane connection. Separate the select traces from sensitive common-terminal routing, especially where a shared amplifier follows the mux. Preserve the 16-SOIC footprint exactly when creating a replacement design, and confirm pin orientation, exposed thermal requirements if applicable, and soldering-profile details from the package documentation.
Thông tin tuân thủ
The manufacturer product information identifies Pb-free packages. Specific RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 claims must be confirmed for the exact ordering code.