onsemi

MC14053BD - Triple 2:1 Analog Multiplexer | onsemi

部品番号: MC14053BD ✓ 生産中
3.0 V to 18 V Vdss 280 ohm Rds(on) 16-SOIC Package
MOQ: 1 |

MC14053BD 概要

onsemi MC14053BD is a triple 2:1 analog multiplexer and demultiplexer IC designed to route analog signals among multiple channels using digital control inputs. The device is identified as a 3-circuit IC switch with 280 ohm on-state resistance in a 16-SOIC package. According to the manufacturer product information, its supported analog signal range is 3.0 V to 18 V when VEE is no higher than VSS, making it suitable for conventional CMOS control and low-voltage analog signal routing systems.

An analog multiplexer is a semiconductor switching device that connects one of several signal terminals to a common terminal. The MC14053B family provides three independent 2:1 selections, allowing multiple analog sources to be routed through one shared signal path. Digital select inputs determine which source or destination is connected, while the analog switches provide bidirectional signal paths suitable for multiplexed and demultiplexed operation.

Key features include three independently controlled 2:1 analog switches, 280 ohm on-state resistance, operation over a 3.0 V to 18 V analog voltage range, and a 16-SOIC package. The manufacturer also identifies low-noise performance of 12 nV per square-root-hertz for frequencies up to 1.0 kHz. These characteristics make the device useful for sensor selection, measurement routing, signal conditioning, test systems, and other applications requiring controlled analog-channel access.

The MC14053B is part of the CMOS logic family of analog switches. Its digital control architecture allows a microcontroller or logic controller to select among signal paths without changing the physical routing of the analog network. Because the device is bidirectional, the same switching network can support multiplexing, demultiplexing, signal swapping, and routing functions depending on the external circuit configuration.

Typical applications include multiplexed sensor interfaces, instrumentation signal routing, data acquisition systems, communication equipment, and industrial control modules. In a sensor interface, the select lines can choose among several inputs before amplification or conversion. In a data acquisition circuit, separate control logic can direct different sources to a shared analog front end while minimizing the number of separate signal-chain channels.

Designers should confirm the actual pinout, control truth table, supply limits, and input voltage limits in the manufacturer datasheet before layout. The unused selector and signal terminals should be handled according to the datasheet guidance, and the common analog path should be kept away from switching nodes and high-current return paths to reduce coupling and crosstalk.

This page consolidates the manufacturer product information, package identification, channel configuration, on-state resistance, supported voltage range, and low-noise figure into a practical reference for engineers selecting an analog multiplexer. It also distinguishes device-level switching facts from parameters that must be confirmed directly from the datasheet.

ドロップイン代替品: MC14053BD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MC14053BD (同一形状・フットプリント) — 相違点: Package, Mounting Type, On-State Resistance, Product Type, Switch Configuration.

Texas Instruments
Package: 16-pin PDIP
Mounting Type: Through-hole
Product Type: Triple 2:1 SPDT analog multiplexer/demultiplexer with logic-level conversion
比較対象 MC14053BD →
onsemi
Package: 16-SOEIAJ
On-State Resistance: 280 ohms typical
比較対象 MC14053BD →

MC14053BF

✅ ドロップイン
onsemi
📦 16-SOIC
Triple SPDT, 3 circuits · 2:1 per circuit · 3.0 V to 18 V · 280 ohms typical · 12 nV/sqrt(Hz) typical at 1.0 kHz · 3 V to 18 V · 16-SOEIAJ · 16 pins

価格はお問い合わせください

データシートを見る →

MC14053BFG

✅ ドロップイン
📦 16-SOIC
Same MC14053B triple 2:1 function and 16-SOIC package; ordering-code and qualification details must be verified.

📋 参考代替品(カタログ未掲載)

NLV14053BDR2G

✅ ドロップイン
📦 16-SOIC
Cross-reference information identifies the same triple 2:1 multiplexer function, 16-pin SOIC package, and consistent terminals; final electrical limits require comparison.

📋 参考代替品(カタログ未掲載)

NLV14053BDG

✅ ドロップイン
📦 16-SOIC
Same MC14053B-family triple 2:1 multiplexing function and 16-SOIC package; qualification and ordering-code differences require review.

📋 参考代替品(カタログ未掲載)

CD4053BE

✅ ドロップイン
Texas Instruments
📦 16-SOIC
Triple 2:1 SPDT analog multiplexer/demultiplexer with logic-level conversion · 3 circuits · 2:1 SPDT per channel · 20 V · 240 ohm · Supported · -55 °C to +125 °C · 16-pin PDIP

価格はお問い合わせください

データシートを見る →

MC14053BD 仕様

Product Type Triple 2:1 analog multiplexer/demultiplexer
Number of Circuits 3 circuits
Switch Configuration 2:1
On-State Resistance 280 ohm
Analog Voltage Range 3.0 V to 18 V
VEE Constraint VEE must be less than or equal to VSS
Low-Noise Performance 12 nV/sqrt(Cycle) at f <= 1.0 kHz
パッケージ 16-SOIC
ピン数 16 pins
実装タイプ Surface mount
Logic Family CMOS
Signal Path Direction Bidirectional
Multiplexer Channels 3
Select Ratio 2:1

MC14053BD ピン構成

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
ピン 1 [DATA_NEEDED: pin 1 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 2 [DATA_NEEDED: pin 2 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 3 [DATA_NEEDED: pin 3 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 4 [DATA_NEEDED: pin 4 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 5 [DATA_NEEDED: pin 5 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 6 [DATA_NEEDED: pin 6 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 7 [DATA_NEEDED: pin 7 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 8 [DATA_NEEDED: pin 8 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 9 [DATA_NEEDED: pin 9 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 10 [DATA_NEEDED: pin 10 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 11 [DATA_NEEDED: pin 11 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 12 [DATA_NEEDED: pin 12 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 13 [DATA_NEEDED: pin 13 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 14 [DATA_NEEDED: pin 14 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 15 [DATA_NEEDED: pin 15 name] — Use the manufacturer pin-description table for the authoritative assignment.
ピン 16 [DATA_NEEDED: pin 16 name] — Use the manufacturer pin-description table for the authoritative assignment.

主な用途

MC14053BD の用途: 6 件s: Multiplexed Sensor Interface, Data Acquisition Signal Router, Instrumentation Amplifier Signal Selection, Signal Swapping and Test Routing, Communication Equipment Analog Routing, Industrial Control Module.

🧩

Multiplexed Sensor Interface

The MC14053BD fits a sensor-selection front end that must combine several analog inputs before amplification or conversion. Its three independently addressed 2:1 sections allow a controller to select among paired sensor outputs and route the selected signal to a shared analog front end. The listed 280 ohm on-state resistance must be included when checking source impedance and converter settling behavior. Because the switch paths are bidirectional, the same architecture can also route a calibration signal back into the sensor node. Digital select lines should be driven from a controller with levels compatible with the MC14053B control inputs.

📊

Data Acquisition Signal Router

MC14053BD can reduce analog front-end duplication in a data-acquisition system by selecting among multiple sensor or instrument outputs. Each 2:1 section routes one of two inputs to a shared channel, and the three sections can support several independent measurement selections. The 3.0 V to 18 V analog range accommodates conventional low-voltage measurement signals, while the 280 ohm on-state resistance needs to be checked against the source impedance and downstream converter input. Place the selected signal path away from digital clocks and provide a stable return path to minimize crosstalk.

🖥️

Instrumentation Amplifier Signal Selection

The MC14053BD is useful when several conditioned instrumentation signals must feed one higher-precision amplifier or analog-to-digital converter. Three 2:1 switch sections can select among sensor, reference, or calibration inputs without requiring a separate amplifier channel for every source. The device's 12 nV per square-root-hertz family noise figure at frequencies up to 1.0 kHz supports low-noise routing, while its 280 ohm on-state resistance contributes to source impedance and should be evaluated with the amplifier input network. A high-impedance buffer may be required when the downstream stage cannot tolerate added loading.

🔧

Signal Swapping and Test Routing

MC14053BD can implement bidirectional signal swapping in test and conditioning circuits where a controller must alternate between two paths without mechanically changing the connection. Because each section contains two selectable terminals and a common terminal, the device can support routing, swapping, and demultiplexing arrangements depending on the external wiring. The manufacturer identifies a 3.0 V to 18 V analog range and 280 ohm on-state resistance. Test engineers should include the switch resistance in the expected insertion loss and account for control timing when sequencing measurements.

🌐

Communication Equipment Analog Routing

MC14053BD can route low-frequency analog paths within communication equipment when several sources need access to a shared receive or transmit chain. The three independent 2:1 sections provide flexible channel selection under digital control, while the 280 ohm on-state resistance makes it particularly relevant to high-impedance signal paths rather than low-ohm power routing. Designers should check the datasheet for operating voltage, logic thresholds, switching time, and leakage at the intended signal frequency. Shield or guard the common path if switching transients could disturb adjacent communication channels.

🏭

Industrial Control Module

MC14053BD can support analog channel selection in an industrial control module that accepts references, feedback signals, or sensor outputs from several external sources. Its three 2:1 sections allow the controller to share one conditioning path, reducing the number of discrete analog routes. The supported 3.0 V to 18 V analog range covers common control-system signal levels, and the family is identified as Pb-free packaged. Engineers should still confirm the exact operating temperature, supply configuration, and qualification requirements for the selected ordering code before using the part in an industrial installation.

What is the onsemi MC14053BD?
The onsemi MC14053BD is a triple 2:1 analog multiplexer/demultiplexer IC with three independently controlled 2:1 switch circuits. The manufacturer product page identifies it as part of the MC14053B analog-switch family, with 280 ohm on-state resistance and operation in a 16-SOIC package. It is used to route analog signals between multiple sources and a shared path. According to onsemi, the device supports analog voltages from 3.0 V to 18 V when VEE is no higher than VSS.
How many analog channels does the MC14053BD switch?
The MC14053BD contains three 2:1 analog switch circuits. Each circuit can connect one of two signal positions to a common terminal under digital select control, allowing three separate routing decisions. The product listing describes the device as a 3-circuit IC switch with a 2:1 configuration. This makes it suitable for routing three pairs of analog signals, provided the external circuit uses the device's bidirectional switching paths according to the manufacturer pinout and truth table.
What is the on-state resistance of the MC14053BD?
The MC14053BD has a listed on-state resistance of 280 ohm. This value is one of the key parameters to evaluate when selecting the device for signal routing, especially when source impedance, ADC input capacitance, or permissible insertion loss matters. The 280 ohm figure is the manufacturer-specified switching resistance for the MC14053B family and should be considered together with the signal-current and operating-voltage conditions in the datasheet.
Where can I download the MC14053BD datasheet PDF?
The MC14053BD technical information is available through the onsemi product page for the MC14053B family. The product page links to the family datasheet and lists the device as a 3-circuit, 2:1 analog multiplexer/demultiplexer with 280 ohm on-state resistance. For a definitive connection, consult the datasheet pin-description table, control truth table, and electrical-characteristics section before assigning PCB traces or selecting external resistors.
What is the MC14053BD pinout?
The MC14053BD uses a 16-SOIC package and provides three 2:1 analog switch circuits with digital select control. The exact signal names, select-pin assignments, common terminals, supply pins, and unused-pin requirements must be taken from the manufacturer datasheet pin-description table. Use that table when assigning PCB tracks; the package alone does not determine the switch orientation. The manufacturer product page identifies the package as 16-SOIC, while the datasheet provides the authoritative numbered pin assignment.
Is MC14053BD suitable for multiplexing sensor signals?
Yes, MC14053BD is suitable for multiplexing sensor signals when the signal amplitude and bandwidth remain within the device's specified operating conditions. Its three 2:1 switch sections let a controller route multiple sensor outputs toward a shared amplifier or converter, while the listed 280 ohm on-state resistance must be included in the source-impedance design. The device is especially useful where several low-bandwidth sensor channels need to be selected without duplicating the entire analog front end.
Can the MC14053BD be used as a demultiplexer?
Yes, the MC14053BD can be used as a demultiplexer because its analog switches are bidirectional and can route a common signal to one of two positions in each section. The digital select inputs then determine which destination receives the signal. This arrangement is useful for sharing an amplifier or converter across two possible destinations, although the external circuit must account for the listed 280 ohm on-state resistance and the datasheet's switching and control requirements.
What voltage range can the MC14053BD switch?
The MC14053B family supports an analog voltage range of 3.0 V to 18 V, calculated as VDD minus VEE. The manufacturer also states that VEE must be no higher than VSS. This is the analog signal range identified for the family and should not be confused with a complete listing of every supply, logic-level, and absolute-maximum rating. Check the manufacturer datasheet for the exact operating combinations used in the design.
What can replace the MC14053BD?
The MC14053B family members MC14053BF and MC14053BFG are the closest same-manufacturer alternatives identified for this function, while NLV14053BDR2G and NLV14053BDG are listed in cross-reference comparisons as compatible replacements. A replacement is a true drop-in choice only when its package, pin assignments, control logic, voltage range, and electrical characteristics match the original. Compare the manufacturer datasheets before substitution, especially where automotive qualification or packaging options affect the selection.
Is MC14053BD the same as NLV14053BDR2G?
MC14053BD and NLV14053BDR2G are identified by cross-reference information as functionally comparable 16-pin SOIC triple 2:1 analog multiplexers, with consistent terminals and packages. They can therefore be candidates for replacement without PCB changes. Final equivalence must still be confirmed against the datasheets for supply range, on-resistance, logic thresholds, switching time, leakage, and qualification requirements. The MC14053BD remains the baseline part when exact onsemi specification continuity is preferred.
When should I choose MC14053BD instead of NLV14053BDR2G?
Choose MC14053BD when an onsemi MC14053B-family device is required and its documented electrical behavior best matches the existing design. NLV14053BDR2G is a useful same-package alternative when the designer has verified its control logic, analog limits, and operating characteristics against the target application. Both are presented as triple 2:1 analog multiplexers in 16-pin SOIC packages, so selection should emphasize exact datasheet parameters rather than package appearance alone.
Is MC14053BD suitable for 5 V analog signal routing?
MC14053BD can be considered for 5 V analog signal routing when the applied signal remains inside the MC14053B family's 3.0 V to 18 V analog voltage range and the complete power-supply configuration satisfies the datasheet. The 280 ohm on-state resistance can add signal loading and may require a high-impedance following stage. Check logic thresholds to ensure the controller reliably asserts the select inputs, and review maximum signal current before committing to the design.
How should I choose between MC14053BF and MC14053BFG?
MC14053BF and MC14053BFG are same-family options for the MC14053BD function, so the decisive differences are the exact ordering codes, package or delivery configuration, and any qualification or marking differences defined by their manufacturer documentation. Do not select based on the final letter alone. Compare the ordering information, package details, temperature rating, qualification claims, and datasheet limits in the manufacturer documentation before treating either part as a drop-in replacement.
What are the key specifications of MC14053BD that engineers should know?
The principal MC14053BD specifications are three 2:1 switch circuits, 280 ohm on-state resistance, a 3.0 V to 18 V analog voltage range, and a 16-SOIC package. The manufacturer also lists 12 nV per square-root-hertz low-noise performance for frequencies up to 1.0 kHz. These figures identify the device as a CMOS analog routing switch, but application suitability still depends on control levels, leakage, switching speed, operating temperature, and absolute maximum ratings in the datasheet.
Where can I buy MC14053BD and what is its price?
Use the Request a Quote form on this page to ask for MC14053BD availability, current pricing, order quantity, and delivery timing. The XAIPART commercial workflow provides a single request path instead of embedding a static price that can become stale. For technical qualification, include the required package variant, production quantity, and target date in the request so the supply team can confirm the appropriate MC14053BD ordering code and delivery conditions.
Is MC14053BD in stock and what is its lead time?
Current MC14053BD stock, minimum order quantity, and lead time should be confirmed through the Request a Quote form on this page. Availability can vary by ordering code, packaging, quantity, and manufacturing status, so an old catalog status should not be treated as a live allocation. Include your required quantity and project schedule in the request to obtain the most useful confirmation from the supplier.
Does MC14053BD meet RoHS and automotive requirements?
MC14053BD should not be assumed to meet every environmental or automotive requirement without checking its specific ordering code and manufacturer declarations. The onsemi product family information identifies Pb-free packaging, but RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status must be confirmed for the exact part. The device's role in an automotive system also does not by itself make the IC AEC-Q100 qualified; request the applicable compliance and qualification documentation.

エンジニアリング参考データ: MC14053BD — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose MC14053BD when the design needs a onsemi MC14053B-family triple 2:1 analog multiplexer in a 16-SOIC package and the manufacturer specification continuity is preferred. Its listed 280 ohm on-state resistance, 3.0 V to 18 V analog range, and 12 nV/sqrt(Cycle) family noise figure make it appropriate for multiplexed sensor, instrumentation, and bidirectional routing circuits. MC14053BF and MC14053BFG are same-family candidates when their ordering codes, qualification, and delivery details meet the production requirement. NLV14053BDR2G and NLV14053BDG are cross-reference options that should be selected only after comparing control thresholds, electrical limits, and qualification documents. CD4053B is relevant because onsemi identifies the MC14053B as a typical pin-for-pin replacement, but its on-resistance and operating specifications may differ. For every alternative, verify the exact pinout, truth table, supply limits, temperature range, and reliability requirements before approving a drop-in substitution.

代替品との比較

パラメータ この製品 MC14053BF MC14053BFG NLV14053BDR2G NLV14053BDG CD4053B
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Brand onsemi onsemi onsemi onsemi onsemi onsemi
Switch Configuration Triple 2:1 Triple 2:1 Triple 2:1 Triple 2:1 Triple 2:1 Triple 2:1
Number of Circuits 3 circuits 3 circuits 3 circuits 3 circuits 3 circuits 3 circuits
Pin Count 16 pins 16 pins 16 pins 16 pins 16 pins 16 pins
Special Feature Low-noise MC14053B family MC14053B family variant MC14053B family variant NLV14053B family variant NLV14053B family variant CD4053 family variant

主な差別化要因

  • Three independently controlled routing sections in one IC (vs CD4053B)
  • Documented low-noise family performance (vs MC14053BF)
  • Explicit 280 ohm on-state resistance (vs NLV14053BDR2G)

設計ノート

Treat the selected common path as a sensitive analog node. The MC14053BD has a listed on-state resistance of 280 ohm, so source impedance, downstream input capacitance, and settling time should be evaluated together. Keep the common path away from digital select traces and high-impedance amplifier inputs. If crosstalk appears during channel changes, increase separation from switching nodes, use a ground guard where appropriate, and verify that downstream circuitry does not amplify charge-injection transients.

Do not infer the select truth table from the generic 2:1 label. Assign the select pins, common terminals, supply pins, and signal terminals directly from the manufacturer pin-description table and control truth table. Also distinguish the 3.0 V to 18 V analog voltage range from the complete supply and absolute-maximum specifications. The manufacturer notes that VEE must be no higher than VSS, so negative or unusual supply arrangements require separate verification before layout.

Place the MC14053BD close to the sources and destinations that share its analog path. Keep each analog route short and pair it with a continuous return-plane connection. Separate the select traces from sensitive common-terminal routing, especially where a shared amplifier follows the mux. Preserve the 16-SOIC footprint exactly when creating a replacement design, and confirm pin orientation, exposed thermal requirements if applicable, and soldering-profile details from the package documentation.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Yes
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The manufacturer product information identifies Pb-free packages. Specific RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 claims must be confirmed for the exact ordering code.

関連検索

MC14053BD datasheet MC14053BD pinout MC14053BD datasheet pdf MC14053BD equivalent MC14053BD replacement MC14053BD cross reference MC14053BD vs NLV14053BDR2G MC14053BD footprint MC14053BD application circuit onsemi MC14053BD MC14053BD price MC14053BD stock MC14053BD 280 ohm MC14053BD triple 2:1 multiplexer

関連部品&用語

onsemi MC14053BD MC14053BF MC14053BFG NLV14053BDR2G NLV14053BDG CD4053B analog multiplexer analog demultiplexer analog switch interface IC semiconductor CMOS bidirectional signal path 2:1 switch configuration 280 ohm on-state resistance analog voltage range low-noise switching 16-SOIC SOIC package family surface mount digital select control sensor multiplexing data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示