MC14516BF - 4-Bit Synchronous Up/Down Counter | onsemi
MPN: MC14516BF ✓ Hoạt độngMC14516BF Tóm tắt
A synchronous binary counter is a sequential logic device that advances or reverses its four-bit output state on each active clock transition. The MC14516BF belongs to the broader CMOS counter hierarchy, where counter ICs provide repeatable digital state generation for timing, sequencing, arithmetic, and industrial control. Unlike a simple ripple counter, its internally synchronous architecture coordinates state transitions for predictable operation in clocked digital systems.
The primary features of the MC14516BF include a 3.0 V to 18 V supply range, internal synchronization, diode protection on all inputs, and four preset inputs. Preset data can be loaded into the counter by applying the desired binary value and asserting the preset-enable control. This combination supports repeatable initialization, programmable step sequences, and compact state management in systems that need more flexibility than a fixed modulus counter.
Internally, the monolithic construction combines P-channel and N-channel enhancement-mode MOSFETs. The four output bits represent the current count, while separate direction, clock, preset-enable, and preset-data controls allow the system designer to choose between counting and parallel loading. Because the device operates from 3.0 V through 18 V, it can be used with both low-voltage digital systems and higher-voltage industrial control environments, subject to the input and output limits in the manufacturer datasheet.
Typical applications include industrial sequence controllers, programmable timing modules, digital instrumentation, batch-counting equipment, and control systems that periodically divide an event stream into groups. The counter is also useful in laboratory and test equipment where a repeatable four-bit state must advance at each clock edge. A design can use the outputs as address bits, time-slot indicators, step markers, or binary control signals.
For reliable implementation, review the manufacturer pin-description table and the input transition and timing diagrams before assigning logic levels. Account for setup and hold requirements around the clock, direction, and preset controls. Ensure unused inputs are connected to a defined valid state and include reset or preset sequencing in the controller startup routine. The 16-pin SOP footprint also requires an appropriate land pattern and adequate clearance between adjacent copper features.
This product page combines the manufacturer function description with practical sourcing, replacement, pinout-location, and circuit-integration guidance. It also distinguishes documented device characteristics from parameters that still require verification against the latest ON Semiconductor datasheet, helping engineers move from selection to schematic capture with fewer component-level questions.
Bộ thay thế dễ dàng lắp đặt cho MC14516BF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
CD4516BNSRE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CD4516BNSRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CD4516BNSR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC14516BF Tỷ lệ tối đa & tính chất điện
| Counter Type | 4-bit synchronous binary up/down counter |
| Supply Voltage Range | 3.0 V to 18 V |
| Logic Family | CMOS |
| Internal Architecture | Synchronous |
| Transistor Technology | P-channel and N-channel enhancement-mode MOSFETs |
| Input Protection | Diode protection on all inputs |
| Output Count Width | 4 bits |
| Preset Inputs | 4 parallel binary preset inputs |
| Hộp | 16-pin SOP (PDSO16) |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MC14516BF 16-pin sop (pdso16)
Cấu hình chân cho MC14516BF (16-pin sop (pdso16) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MC14516BF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MC14516BF phù hợp cho 6 Áp dụngs: Industrial Sequence Controller, Programmable Timing and Event Divider, Digital Instrumentation and Test Equipment, Batch Counting and Product Tracking, Programmable Logic Controller, Digital Clock Divider and Phase Sequencer.
Industrial Sequence Controller
The MC14516BF fits an industrial sequence controller because it provides four binary state bits, selectable up or down counting, and parallel preset loading within a 3.0 V to 18 V supply range. A controller can advance one step on each active clock edge and use P0 through P3 with preset enable to return to a defined machine state. This supports repeatable actuator, relay, or process-stage sequencing without requiring a separate preset register. The synchronous internal arrangement makes the state changes easier to coordinate with surrounding control logic. Designers should still verify clock-edge timing, setup and hold requirements, and valid control states directly from the ON Semiconductor datasheet before releasing production hardware.
Được đề xuất
Programmable Timing and Event Divider
A programmable timing module can use the MC14516BF to divide a recurring event stream into a four-bit sequence. Each active clock transition changes the count in the selected direction, providing a compact sequence of 16 representable states for time-slot selection, duty-cycle staging, or repeat-count control. The device’s 3.0 V to 18 V operating range permits use across many industrial logic levels. Preset loading allows the timer to restart from a chosen state instead of requiring an external counter reset path. For timing-critical designs, check the manufacturer’s maximum clock frequency and propagation-delay limits at the selected supply voltage before treating the counter as a precision time-base element.
Được đề xuất
Digital Instrumentation and Test Equipment
The MC14516BF can organize instrument events into a repeatable four-bit state in digital measurement and test equipment. The count outputs may represent captured samples, measurement stages, calibration steps, or pass/fail sequences, while the preset inputs allow a test cycle to begin from a known state. The 16-pin SOP package supports compact PCB layouts, and the broad 3.0 V to 18 V supply specification accommodates multiple legacy and industrial logic environments. Synchronous operation helps align count changes with the instrument’s clock. Validate noise margins, clock-edge timing, and output behavior across the complete operating voltage because instrument accuracy can depend on deterministic state transitions.
Được đề xuất
Batch Counting and Product Tracking
For batch counting and product tracking, the MC14516BF provides a compact modulo-16 event tally with controllable count direction. A sensor or machine event can drive the clock, while the four outputs represent the current quantity from 0 through 15. The preset inputs are useful when a new batch must begin at a known count or when an external system initializes the sequence. Its 3.0 V to 18 V supply range is useful in industrial equipment with legacy CMOS logic levels. The design should include a defined startup state, verify the active clock edge, and ensure that the controller recognizes rollover or preset behavior before relying on the outputs for downstream decisions.
Được đề xuất
Programmable Logic Controller
The MC14516BF can serve as a compact state sequencer within a programmable logic controller or small industrial control board. Four counter outputs provide a 16-step state code that can drive selectors, relay-enable logic, or stage indicators, while the direction input permits descending as well as ascending sequences. Preset enable and P0 through P3 let the controller jump directly to a defined state during initialization or recovery. The internal synchronous design supports coordinated transitions on the active clock edge. Engineers should establish valid logic states for every control input and check timing requirements in the ON Semiconductor datasheet before using the counter outputs as safety-critical control signals.
Được đề xuất
Digital Clock Divider and Phase Sequencer
The MC14516BF can divide a master clock into a four-bit phase or step sequence for digital clock-distribution and timing-control circuits. Counting on each active edge, the device creates a repeating 16-state progression that can enable different circuit phases, capture windows, or sequential loads. The preset function allows the phase sequence to begin from a known position, which is useful after reset or a system-mode change. Its 3.0 V to 18 V supply range and 16-pin SOP package make it suitable for compact control logic. Confirm maximum operating frequency, propagation delay, and clock-edge behavior at the intended voltage so that generated phases retain the required timing margin.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC14516BF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | CD4516BNSRE4 | CD4516BNSRG4 | CD4516BNSR |
|---|---|---|---|---|
| Package | SOP-16 (PDSO16) | SOP-16 | SOP-16 | SOP-16 |
| Brand | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Counter Type | 4-bit synchronous binary up/down counter | 4-bit binary up/down counter | 4-bit binary up/down counter | 4-bit binary up/down counter |
| Supply Voltage Range | 3.0 V to 18 V | 3.0 V to 18.0 V | 3.0 V to 18.0 V | 3.0 V to 18.0 V |
| Output Width | 4 bits | 4 bits | 4 bits | 4 bits |
| Pin Count | 16 pins | 16 pins | 16 pins | 16 pins |
| Preset Function | Parallel preset with preset enable | Counter preset function | Counter preset function | Counter preset function |
Bảo phân biệt quan trọng
- Direct onsemi source for the MC14516B family (vsCD4516BNSRE4)
- Synchronous internal architecture (vsCD4516BNSRG4)
- Parallel preset with dedicated enable control (vsCD4516BNSR)
Ghi chú thiết kế
Treat the clock edge, count direction, preset enable, and preset data as a coordinated control interface. Do not assume that changing direction is safe at every clock boundary; establish the intended direction before the active edge. Use the ON Semiconductor logic diagrams and timing specifications to confirm setup and hold requirements, and give every control input a defined state during startup and reset.
Follow the manufacturer package drawing when creating the 16-pin SOP land pattern and confirm pin 1 orientation against the PCB silkscreen and component marking. Place bypass capacitors near the supply and ground connections, route clock traces away from noisy analog or switching nodes, and maintain adequate clearance between adjacent signals. Confirm land dimensions against the latest package drawing before fabrication.
The counter should be clocked by a clean, repeatable signal because timing errors can appear as incorrect count or preset behavior. Keep the clock path short, provide a low-impedance return path, and avoid unnecessary stubs or test-pad capacitance on sensitive timing nodes. Validate the maximum operating frequency, propagation delay, and setup margins at the actual supply voltage used by the finished assembly.
Decouple the supply close to the device with capacitance selected from the ON Semiconductor datasheet and the switching characteristics of the surrounding circuit. The documented supply range is 3.0 V to 18 V, but the valid operating range for every input and output also depends on VDD and temperature. Check the complete electrical-characteristics table before selecting pull-up, pull-down, or interface components.
Thông tin tuân thủ
No explicit environmental or automotive qualification status was identified for the MC14516BF. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status with ON Semiconductor before procurement.