MC33502DG - Dual 1V Rail-to-Rail Op Amp | onsemi
MPN: MC33502DG ✓ Hoạt độngMC33502DG Tóm tắt
An operational amplifier is a high-gain analog signal-conditioning circuit used in the wider hierarchy of analog ICs, signal-chain components, and semiconductor devices. The MC33502DG combines differential input amplification, voltage feedback, and output-drive capability in two channels. Rail-to-rail inputs let the amplifier operate across nearly the complete input supply range, while rail-to-rail outputs improve signal swing when the available supply voltage is limited.
Key characteristics include a 1.0 V operating supply, a 7 V maximum supply, dual-channel configuration, and output swing within 50 mV of either supply rail. These characteristics suit portable equipment, battery-powered instrumentation, sensor interfaces, and low-voltage industrial controls where the signal must be amplified without a high-voltage supply. The 8-SOIC package also supports conventional surface-mount assembly and automated board production.
The MC33502 architecture is intended for low-voltage rail-to-rail operation. Under a 1.0 V supply and ground, the amplifier can still operate, while its input and output stages use the available supply range. Because the output remains approximately 50 mV from either rail, designers should leave this margin when calculating the usable output range. The dual configuration also reduces package count when two similar amplifier functions are required on the same board.
Typical applications include battery-powered sensor conditioning, low-voltage audio and communication interfaces, current sensing, portable medical instrumentation, industrial control modules, and general-purpose analog signal buffering. In a current-measurement circuit, the MC33502DG can amplify the voltage produced across a low-value shunt while operating from a low-voltage rail. Its rail-to-rail inputs help preserve signal range in compact systems.
When laying out a design, place the amplifier input and output routes away from switching nodes and high-current supply paths. Stable operation with the intended load and feedback network should be confirmed from the manufacturer datasheet, especially when driving long PCB traces, large capacitors, or cable capacitance. Decoupling capacitors should be placed close to the supply pins to suppress local supply noise.
This product page combines the manufacturer electrical characteristics, package information, application guidance, and verified drop-in cross-reference results. It also identifies the differences that matter when evaluating the MC33502DG against other low-voltage dual rail-to-rail operational amplifiers, while avoiding confusion between electrical equivalence and purely different order codes.
Bộ thay thế dễ dàng lắp đặt cho MC33502DG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TSV992AIDT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS922AIDT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC33502DG Tỷ lệ tối đa & tính chất điện
| Product Type | Dual rail-to-rail operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Supply Voltage Range | 1.0 V to 7 V |
| Minimum Operating Supply | 1.0 V |
| Maximum Operating Supply | 7 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Within 50 mV of each supply rail |
| Khoảng nhiệt độ hoạt động | -40 °C to +105 °C |
| Temperature Grade | Industrial |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân MC33502DG
| Chân 1 | OUTA — Amplifier A output |
| Chân 2 | INA− — Inverting input for amplifier A |
| Chân 3 | INA+ — Non-inverting input for amplifier A |
| Chân 4 | V− — Negative supply or ground connection |
| Chân 5 | INB+ — Non-inverting input for amplifier B |
| Chân 6 | INB− — Inverting input for amplifier B |
| Chân 7 | OUTB — Amplifier B output |
| Chân 8 | V+ — Positive supply connection |
Ứng dụng tiêu biểu
MC33502DG phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Interfaces, Portable Medical Monitoring, Industrial Current Sensing, Low-Voltage Audio Buffering, Portable Communication Interfaces, Low-Voltage Control and Analog Monitoring.
Battery-Powered Sensor Interfaces
The MC33502DG fits battery-powered sensing circuits because both amplifier channels operate from a supply as low as 1.0 V. Rail-to-rail inputs help retain the usable range of a shrinking battery voltage, while rail-to-rail outputs reduce the voltage lost when driving the next analog stage. The device can amplify a bridge, resistive sensor, or low-voltage transducer signal without requiring a higher-voltage analog rail. Its 8-pin SOIC package also limits board area, although input offset, noise, and bias-current characteristics must be checked against the sensor's resolution requirements.
Được đề xuất
Portable Medical Monitoring
The MC33502DG is suitable for compact medical-monitoring signal paths operating from low-voltage rails. Its two independent channels can support related analog measurements without requiring two separate amplifier packages, helping reduce board area and component count. The 1.0 V minimum operating supply supports battery-powered operation, while rail-to-rail input behavior preserves signal excursion as supply voltage declines. Design work should still evaluate noise, offset voltage, patient protection, isolation requirements, and applicable medical-system standards independently of the amplifier's general-purpose rating.
Được đề xuất
Industrial Current Sensing
The MC33502DG can amplify the differential voltage generated by a current shunt in low-voltage industrial control systems. Rail-to-rail input operation is valuable when the shunt voltage occupies much of the available signal range, while the dual channel allows the amplifier to handle a current measurement and another related analog signal. The 1–7 V supply range accommodates low-voltage industrial rails. Confirm input offset and bias behavior, shunt impedance, amplifier stability, and the required common-mode range before finalizing the measurement path.
Được đề xuất
Low-Voltage Audio Buffering
The MC33502DG can serve as a low-voltage buffer or gain stage in portable audio and communication equipment. Rail-to-rail output capability allows the amplifier to provide more of the available signal swing than a conventional non-rail-to-rail device, and two channels can support left and right signal paths. Operation from 1.0 V supports compact, energy-conscious designs. Audio engineers should verify output-noise density, distortion, gain-bandwidth product, load stability, and drive capability at the intended frequency before using the device in a signal chain.
Được đề xuất
Portable Communication Interfaces
The MC33502DG is useful for conditioning low-level signals in portable radio and communication interfaces. Its dual-channel architecture supports separate receive or control paths, while operation down to 1.0 V complements compact radio front ends powered from low-voltage rails. Rail-to-rail inputs and outputs improve signal utilization in constrained analog sections. Because a general-purpose amplifier is not automatically a full interface solution, engineers should verify input impedance, output drive, channel-to-channel behavior, high-frequency stability, and the communications system's impedance requirements.
Được đề xuất
Low-Voltage Control and Analog Monitoring
The MC33502DG can amplify control and monitoring signals in compact industrial equipment operating from a 1–7 V rail. Two channels allow one device to handle a feedback signal and a sensor or actuator interface, reducing package count on area-constrained boards. The low minimum supply voltage supports systems whose main rail falls during standby, and rail-to-rail operation improves signal range. Designers should confirm the device's offset, bandwidth, output-drive, and capacitive-load characteristics against the control-loop bandwidth and output impedance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC33502DG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TSV992AIDT | TS922AIDT |
|---|---|---|---|
| Brand | onsemi | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Channels | 2 | 2 | 2 |
| Input Common-Mode Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Bảo phân biệt quan trọng
- Lower minimum supply requirement (vsTSV992AIDT)
- Documented output swing margin (vsTS922AIDT)
- Two-channel integration in 8-pin SOIC (vsLM2904PWR)
Ghi chú thiết kế
Place the supply-decoupling capacitor immediately between pins 8 and 4, with the shortest possible ground return. Because the MC33502DG can operate from 1.0 V, supply routing and bypass placement become particularly important as the available rail approaches the signal's operating range. Keep high-current switching-node copper away from the amplifier pins and use a quiet return path so that switching ripple is not coupled into the input or output nodes.
Route each inverting input directly to its feedback resistor or capacitor to minimize parasitic capacitance and susceptibility to interference. The non-inverting input should remain away from output routing, inductors, and switching nodes. For a dual amplifier in an 8-pin SOIC, check the placement of both channels so that a high-impedance input on one side is not surrounded by the output or supply pins of the other channel. Use a continuous ground plane unless the return-current path requires a deliberate split.
Do not assume rail-to-rail output reaches either supply voltage exactly. According to the onsemi MC33502 datasheet, the output can swing within 50 mV of each rail, leaving a margin that must be included in output-range calculations. Also avoid selecting a substitute solely by package outline: confirm channel assignment, supply limits, input common-mode range, output swing, stability, and load-drive capability before replacing the MC33502DG in an existing design.
Thông tin tuân thủ
The MC33502DG is an industrial-temperature general-purpose operational amplifier. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly identified in the manufacturer or listing information and therefore remain unknown.