NXP Semiconductors

MC33660EF - ISO 9141 K-Line Interface | NXP | Automotive

MPN: MC33660EF ✓ Hoạt động
8-pin SOIC Package
MOQ: 1 |

MC33660EF Tóm tắt

The NXP Semiconductors MC33660EF is an ISO 9141 K-line serial-link interface IC for bidirectional, half-duplex communication between an automotive on-board microcontroller and an off-board diagnostic system. It is packaged in an 8-pin SOIC and combines a bus-side driver with the circuitry required to interface a vehicle diagnostic network.

An ISO K-line transceiver is an automotive interface device that connects a microcontroller's serial communications port to the physical diagnostic bus. It belongs to the broader interface IC and vehicle-network communication hierarchy. Its purpose is to translate controller-level logic into an appropriate bus signal, support in-vehicle diagnostic communication, and provide bus-side fault protection where the connected wiring can be exposed to shorts or excessive temperature.

According to the NXP manufacturer datasheet, the MC33660 is designed to meet the ISO 9141 diagnostic-system specification. The interface supports bi-directional, half-duplex operation, allowing the same physical connection to transmit requests and receive responses. Its K-line bus-driver output is protected against bus shorts and over-temperature conditions, addressing common electrical stresses encountered in automotive diagnostic environments.

The 8-SOIC package makes the MC33660EF suitable for compact automotive electronic-control units, diagnostic scan tools, passenger-compartment modules, powertrain controllers, body-control modules, and gateway electronics. The key design consideration is that the communication node must correctly implement the electrical and timing behavior required by the vehicle's ISO 9141 network rather than treating the device as a general-purpose UART transceiver.

When laying out a circuit using the MC33660EF, place input and output decoupling close to the device, route the K-line connection away from sensitive analog and communication nodes, and review the datasheet's external-component recommendations. The protected bus output does not remove the need for correct connector protection, grounding, vehicle transient design, or system-level diagnostic compliance.

This product summary combines the device function, package information, automotive diagnostic role, and practical interface considerations. It also highlights the distinction between a true pin-compatible replacement and a merely similar interface IC, helping engineers evaluate board changes, protection behavior, and ISO 9141 compatibility before making a sourcing decision.

Bộ thay thế dễ dàng lắp đặt cho MC33660EF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.

Yêu cầu các bộ thay thế

MC33660EF Thông số kỹ thuật

Product Type ISO 9141 K-line serial-link interface IC
Communication Direction Bidirectional
Duplex Mode Half-duplex
Diagnostic Standard ISO 9141
Bus Interface K line
Bus Output Protection Protected against bus shorts and over-temperature conditions
Intended Host Vehicle on-board microcontroller
External Communication Off-board automotive diagnostic system
Hộp 8-pin SOIC
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân MC33660EF 8-pin soic

Cấu hình chân cho MC33660EF (8-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 8-pin soic cho MC33660EF

Không có dữ liệu chân cụ thể sẵn có cho MC33660EF.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MC33660EF phù hợp cho 6 Áp dụngs: Vehicle Diagnostic Interface Modules, Body Control Modules, Powertrain Control Units, Passenger Compartment Modules, Automotive Gateway Electronics, Automotive Scan and Service Interfaces.

🚗

Vehicle Diagnostic Interface Modules

The MC33660EF fits an on-board diagnostic module that exchanges requests and responses with an off-board test system through the ISO 9141 K line. Its bidirectional, half-duplex operation allows a controller to transmit a diagnostic request and receive the corresponding reply over one physical bus. According to the NXP manufacturer datasheet, the K-line bus-driver output is protected against bus shorts and over-temperature conditions, making it a practical choice when the diagnostic connector and harness can expose the electronics to vehicle-wiring faults. The surrounding module still needs appropriate supply conditioning, connector protection, grounding, and diagnostic-network timing.

🚗

Body Control Modules

A body control module can use the MC33660EF to provide an ISO 9141 diagnostic connection between its on-board microcontroller and external service equipment. The device's half-duplex bus interface suits a controller that must issue a diagnostic request, switch direction, and process the response. Its 8-SOIC package is useful where board area is constrained, while the short-circuit and over-temperature protection in the bus-driver output adds robustness at the physical vehicle interface. Production design must confirm the module's supply limits, operating-temperature grade, external components, and network timing against the manufacturer datasheet.

🚗

Powertrain Control Units

The MC33660EF can support diagnostic access in a powertrain electronic-control unit that communicates with an off-board vehicle diagnostic system over ISO 9141. Bidirectional half-duplex communication enables the embedded controller to exchange diagnostic information without requiring separate transmit and receive bus paths. The protected K-line driver output is particularly relevant in an automotive harness environment where wiring shorts or thermal conditions may occur. Because this component addresses the physical diagnostic interface rather than control algorithms, it should be paired with an automotive-capable controller and validated as part of the complete ECU power and qualification design.

🚗

Passenger Compartment Modules

In a passenger-compartment module, the MC33660EF provides a compact ISO 9141 path between the module's microcontroller and vehicle service equipment. The 8-SOIC format supports surface-mount PCB integration, while the bidirectional half-duplex interface reduces the number of physical K-line connections needed for request-and-response diagnostics. The manufacturer datasheet states that the bus-driver output is protected against bus shorts and over-temperature conditions. Engineering review should still address connector pin definition, wake-up behavior, supply sequencing, transient immunity, and the diagnostic timing expected by the vehicle manufacturer.

🚗

Automotive Gateway Electronics

The MC33660EF can be used in gateway or electrical-center electronics that expose an ISO 9141 diagnostic connection to a vehicle microcontroller. The bus interface supports the half-duplex request-and-response pattern used by off-board diagnostic communication. Protection in the K-line output helps the interface tolerate shorts and over-temperature conditions encountered in vehicle wiring, while the 8-SOIC package simplifies board-level routing. The gateway designer must still coordinate protocol routing, diagnostic addressing, wake conditions, ground referencing, and protection at the external connector so that the device operates within its documented electrical limits.

🔧

Automotive Scan and Service Interfaces

The MC33660EF can form part of a service-oriented vehicle interface that connects test equipment to an electronic control unit through the ISO K line. Bidirectional half-duplex communication allows diagnostic commands to travel toward the vehicle and responses to return over the same physical connection. Its protected bus-driver output is useful at the boundary between protected automotive electronics and an accessible diagnostic connector. A practical implementation must include suitable connector-side protection, compliant bus timing, a stable supply source, and verification that the diagnostic protocol and signal levels match the target vehicle network.

What is the MC33660EF?
The MC33660EF is an NXP ISO 9141 K-line serial-link interface IC for bidirectional, half-duplex automotive diagnostic communication. According to the NXP manufacturer datasheet, it connects a vehicle's on-board microcontroller to an off-board diagnostic system through the physical K line. The device is supplied in an 8-pin SOIC package and includes short-circuit and over-temperature protection for its K-line bus-driver output.
What communication standard does MC33660EF support?
The MC33660EF supports the ISO 9141 diagnostic communication specification. According to the NXP manufacturer datasheet, the device is designed to interface an on-board vehicle microcontroller with off-board diagnostic equipment through the ISO K line. It supports bidirectional, half-duplex communication, so a diagnostic node can transmit a request and receive the corresponding response over the same physical bus connection.
Where can I download the MC33660EF datasheet PDF?
The official MC33660 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/MC33660.pdf. Use the manufacturer document for the complete pin-description table, electrical characteristics, recommended external components, timing information, and application circuit. The MC33660EF ordering information is also shown by the manufacturer as an 8-SOIC package variant, which should be checked against the PCB footprint before design release.
Where can I find the MC33660EF pinout?
Use the pin-description table and package drawing in the NXP MC33660 manufacturer datasheet to locate the MC33660EF pinout. The verified product listing identifies the device as an 8-SOIC package, but the individual pin numbers and signal names are not reproduced on this page. Assign PCB nets from the manufacturer's pin table rather than relying on a generic SOIC-8 drawing, because the exposed functions and no-connect positions are package-specific.
MC33660EF vs MC33660BEFR2 - which is the better drop-in replacement?
The MC33660EF and MC33660BEFR2 should be compared using the manufacturer ordering table, electrical characteristics, pin descriptions, and lifecycle qualifications before either is treated as a drop-in replacement. The available cross-reference material identifies the two devices for comparison but does not establish identical pin functions or operating limits. Confirm the package, pinout, supply range, K-line levels, timing, protection behavior, temperature grade, and automotive qualification in the NXP datasheet.
When should I choose MC33660EF over another K-line interface IC?
Choose the MC33660EF when the design requires an ISO 9141 K-line interface, bidirectional half-duplex operation, and an 8-SOIC package in an automotive diagnostic design. It is especially relevant when the controller must communicate with an off-board diagnostic system and the bus output requires short-circuit and over-temperature protection. Choose another device only when its manufacturer explicitly documents equivalent pin compatibility, electrical limits, and diagnostic-system behavior.
Is MC33660EF suitable for automotive diagnostic modules?
The MC33660EF is designed for automotive diagnostic communication between an on-board microcontroller and an off-board diagnostic system. Its ISO 9141 K-line interface, bidirectional half-duplex operation, and protected bus-driver output align with the device's stated role. System qualification still depends on the complete electronic module, its power supply, connector protection, wiring environment, operating-temperature requirements, and the applicable automotive quality process.
What can replace the MC33660EF on an existing PCB?
A valid MC33660EF replacement must be a documented pin-to-pin drop-in in the same 8-SOIC footprint, with compatible supply voltage, K-line electrical limits, communication timing, and protection behavior. The available substitution search does not establish five verified alternatives meeting those conditions. Treat MC33660BEFR2 as a candidate for engineering review, not an approved replacement, and compare both devices against the NXP datasheet and the vehicle interface requirements before changing the BOM.
What is the best drop-in replacement for MC33660EF?
The best drop-in replacement is the device that exactly matches the MC33660EF's 8-SOIC pinout, ISO 9141 K-line electrical characteristics, timing, and protection requirements. MC33660BEFR2 is identified in the cross-reference results as a comparison candidate, but the technical evidence needed to call it a true drop-in is not included here. Confirm the exact NXP ordering variants, package drawing, and electrical limits before approving it for an automotive production design.
Where can I buy MC33660EF online?
Use the Request a Quote form on this page to request MC33660EF pricing, current availability, minimum order quantity, and delivery information. The manufacturer datasheet at https://www.nxp.com/docs/en/data-sheet/MC33660.pdf supports technical evaluation of the 8-SOIC device. Quote requests should include the required quantity, date code preference, and destination so commercial availability can be confirmed for the exact ordering code.
What is the price of MC33660EF?
Use the Request a Quote form on this page for the current MC33660EF price, quantity breaks, availability, and lead time. Pricing for this automotive interface IC can vary with order volume, date code, packaging, and procurement conditions, so a static figure may not represent current market availability. Include your target quantity, approved vendor requirements, and shipment destination in the quote request.
What is the lead time for MC33660EF?
Request the current MC33660EF lead time through the Request a Quote form on this page. The manufacturer datasheet confirms the device's automotive diagnostic function and 8-SOIC package, but it is not a purchasing document and should not be used as a lead-time commitment. Include production forecast, required quantity, and date-code constraints so the commercial response can reflect the actual procurement schedule.
Is MC33660EF in stock?
Use the Request a Quote form on this page to check current MC33660EF stock and order status for the required quantity. A distributor listing alone does not establish XAIPART inventory, so stock should be confirmed for the exact ordering code. Provide your required quantity, ship-to country, authorized-supplier rules, and acceptable date codes to obtain an actionable availability response.
What key specifications should engineers know about MC33660EF?
The key MC33660EF specifications are its role as an ISO 9141 K-line interface, bidirectional half-duplex operation, use between a vehicle microcontroller and an off-board diagnostic system, protected K-line driver output, and 8-SOIC package. According to the NXP manufacturer datasheet, the bus output withstands bus-short and over-temperature conditions. Exact voltage, current, timing, and temperature limits must be taken from the electrical-characteristics and recommended-application sections.
Does MC33660EF need external bus protection?
The MC33660EF includes K-line bus-driver output protection against bus shorts and over-temperature conditions, according to the NXP manufacturer datasheet. That protection does not eliminate all vehicle-level transient requirements. Automotive designs should still evaluate connector exposure, wiring topology, system power architecture, external passive protection where recommended, and diagnostic-network compliance using the complete manufacturer application guidance.

Dữ liệu tham khảo kỹ thuật cho MC33660EF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MC33660EF when an automotive electronic module requires an ISO 9141 K-line physical interface, bidirectional half-duplex communication, and an 8-SOIC package. Its bus-driver output is specified for protection against bus shorts and over-temperature conditions, making it relevant to diagnostic connections exposed to vehicle-wiring faults. Before selecting another interface, verify exact pin compatibility, supply voltage, K-line electrical limits, timing, temperature grade, and automotive qualification. MC33660BEFR2 is a comparison candidate identified in the substitution results, but it should not be released as a drop-in replacement until its manufacturer documentation confirms that every relevant operating and pin parameter matches. The MC33660EF is therefore most appropriate when its documented ISO 9141 behavior, protection, and package align directly with the existing vehicle diagnostic architecture.

Ghi chú thiết kế

Place the MC33660EF close to the protected K-line connector path and keep the bus trace short, continuous, and away from sensitive analog or high-speed communication nodes. Follow the NXP manufacturer datasheet for the exact external-component arrangement. Ground and supply-return paths should be planned together with the K-line return so diagnostic signals do not share noisy high-current return segments.

Do not assume that a similar SOIC-8 interface IC is interchangeable with the MC33660EF. Confirm the manufacturer pin-description table, supply range, K-line output limits, communication timing, temperature rating, and protection specifications before replacing the component. The device's short-circuit and over-temperature protection applies to the bus-driver output and does not replace connector-side transient protection or a complete ISO 9141 network design.

Use the NXP manufacturer datasheet to select the device's local bypass capacitors and power routing. Keep the supply reference stable at the IC and provide adequate ground-plane continuity beneath the package. Because the operating-voltage and current limits are not reproduced here, verify them directly against the manufacturer electrical-characteristics table before sizing the ECU power supply or adding external protection components.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the available manufacturer or distributor information. Confirm qualification and material-compliance documents for the exact ordering code before automotive production release.

Dữ liệu được xác minh vào: 2026-11-11 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

mc33660 k line mc33660 module mc33660 datasheet MC33660EF datasheet MC33660EF datasheet pdf MC33660EF pinout MC33660EF equivalent MC33660EF replacement MC33660EF vs MC33660BEFR2 MC33660EF 8-SOIC MC33660EF automotive diagnostic MC33660EF price

Các bộ phận và thuật ngữ liên quan

NXP Semiconductors MC33660EF MC33660 MC33660BEFR2 ISO 9141 K line ISO K line serial-link interface interface IC automotive diagnostic interface vehicle on-board microcontroller off-board diagnostic system bidirectional communication half-duplex communication 8-SOIC SOIC package family surface mount automotive electronic control unit bus short protection over-temperature protection RoHS REACH AEC-Q100 K-line bus driver vehicle diagnostic network
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ