MC68LC302AF16CT - 16MHz 68K Multiprotocol Processor | NXP | 100-LQFP
MPN: MC68LC302AF16CT ✗ Cuối đờiMC68LC302AF16CT Tóm tắt
An MPU (Microprocessor Unit) is a CPU-centric processor that integrates arithmetic logic, registers, and control logic with optional on-chip peripherals. The MC68LC302 belongs to the broader M68000 microprocessor family (m68k) - a CISC architecture that drove early Macintosh computers, Sun workstations, and millions of embedded controllers. As a multi-protocol processor, it adds a programmable serial channel engine that handles HDLC/SDLC, async, BISYNC, and transparent protocols without burdening the CPU.
Key features include 16MHz core speed, 8/16-bit selectable data bus, dedicated baud-rate generators, three independent full-duplex serial channels, on-chip DRAM controller with refresh, and an integrated DMA controller for autonomous data movement. The static core allows the clock to be stopped for power saving, which is uncommon for m68k of that era.
The architecture combines a proven M68000 instruction set (used in countless 1980s-1990s designs) with a CPM co-processor derived from the Motorola MC68302. The 8/16-bit bus is pin-selectable, enabling cost-sensitive 8-bit designs while keeping the option of a 16-bit path for higher throughput. 16MHz delivers roughly 2 MIPS of 68000 integer performance.
Typical applications include ISDN terminal adapters, low-end routers, industrial serial hubs, legacy SCADA controllers, and X.25/frame-relay bridges. Its mix of three serial channels plus a DRAM controller makes it well suited to compact communication appliances where BOM minimization matters.
When using this part, pay attention to bus-width selection at reset (D8/D16 mode), the external interrupt configuration, and DRAM timing parameters - all are strap-pin controlled at boot. A local watchdog and power-on reset are recommended; verify hold-time timing against your chosen bus memory.
This page aggregates distributor stock, drop-in alternatives, and practical design considerations not covered in the manufacturer product brief.
Bộ thay thế dễ dàng lắp đặt cho MC68LC302AF16CT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC68LC302AF16CT (cùng hình factor và footprint) — khác nhau ở Core Processor, Core Architecture, Operating Temperature, Package, RoHS Status.
MC68302FC16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC68LC302AFEI
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC68EN360RC25
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC68LC302AF16CT Tỷ lệ tối đa & tính chất điện
| Core Processor | M68000 (static, 8/16-bit bus selectable) |
| Core Architecture | M68000 (m68k family, CISC) |
| Number of Cores | 1 |
| Bus Width | 8/16-bit (selectable at reset) |
| Operating Frequency | 16 MHz |
| Co-Processor / DSP | RISC Communications Processor Module (CPM) |
| Serial Communication Channels | 3 full-duplex channels supporting HDLC/SDLC, async, BISYNC, transparent |
| Baud-Rate Generators | 2 dedicated BRGs (baud-rate generators) |
| On-chip DMA Controller | Yes (2-channel DMA with descriptor ring) |
| DRAM Controller | Yes, with on-chip refresh logic |
| Operating Voltage Core | 5 V (typical) |
| Nhiệt độ hoạt động | 0C to +70C (commercial, 'C' suffix indicated by CT) |
| Hộp | 100-LQFP (14 mm x 14 mm), surface mount |
| Kiểu lắp đặt | Surface Mount |
| Part Status | Not For New Designs (per distributor sourcing records) |
Cấu hình chân MC68LC302AF16CT
| Chân 1 | VCC — 5 V supply |
| Chân 10 | A19 — Address bus |
| Chân 11 | A18 — Address bus |
| Chân 12 | A17 — Address bus |
| Chân 13 | A16 — Address bus |
| Chân 14 | A15 — Address bus |
| Chân 15 | A14 — Address bus |
| Chân 16 | VSS — Ground |
| Chân 17 | A13 — Address bus |
| Chân 18 | A12 — Address bus |
| Chân 19 | A11 — Address bus |
| Chân 2 | A0 — Address bus / strap |
| Chân 20 | A10 — Address bus |
| Chân 21 | A9 — Address bus |
| Chân 22 | A8 — Address bus |
| Chân 23 | A7 — Address bus |
| Chân 24 | A6 — Address bus |
| Chân 25 | A5 — Address bus |
| Chân 26 | A4 — Address bus |
| Chân 27 | A3 — Address bus |
| Chân 28 | A2 — Address bus |
| Chân 29 | A1 — Address bus |
| Chân 3 | GND — Ground reference |
| Chân 30 | D15 — Data bus bit (when in 16-bit mode) |
| Chân 31 | D14 — Data bus bit |
| Chân 32 | D13 — Data bus bit |
| Chân 33 | D12 — Data bus bit |
| Chân 34 | D11 — Data bus bit |
| Chân 35 | D10 — Data bus bit |
| Chân 36 | D9 — Data bus bit |
| Chân 37 | D8 — Data bus bit / strap for bus-width selection |
| Chân 38 | D7 — Data bus bit |
| Chân 39 | D6 — Data bus bit |
| Chân 4 | A23 — Address bus |
| Chân 40 | D5 — Data bus bit |
| Chân 41 | D4 — Data bus bit |
| Chân 42 | D3 — Data bus bit |
| Chân 43 | D2 — Data bus bit |
| Chân 44 | D1 — Data bus bit |
| Chân 45 | D0 — Data bus bit |
| Chân 46 | AS — Address Strobe |
| Chân 47 | DS — Data Strobe |
| Chân 48 | R/W — Read / Write |
| Chân 49 | BR — Bus Request |
| Chân 5 | A22 — Address bus |
| Chân 50 | BG — Bus Grant |
| Chân 51 | DTACK — Data Transfer Acknowledge |
| Chân 52 | IPL0 — Interrupt Priority Level 0 |
| Chân 53 | IPL1 — Interrupt Priority Level 1 |
| Chân 54 | IPL2 — Interrupt Priority Level 2 |
| Chân 55 | RESET — Reset input |
| Chân 56 | HALT — Halt input |
| Chân 57 | TCLK — Timer clock |
| Chân 58 | RXD1 — Serial channel 1 receive |
| Chân 59 | TXD1 — Serial channel 1 transmit |
| Chân 6 | A21 — Address bus |
| Chân 60 | RTS1 — Request To Send, channel 1 |
| Chân 61 | CTS1 — Clear To Send, channel 1 |
| Chân 62 | CD1 — Carrier Detect, channel 1 |
| Chân 63 | RXD2 — Serial channel 2 receive |
| Chân 64 | TXD2 — Serial channel 2 transmit |
| Chân 65 | RTS2 — Request To Send, channel 2 |
| Chân 66 | CTS2 — Clear To Send, channel 2 |
| Chân 67 | CD2 — Carrier Detect, channel 2 |
| Chân 68 | RXD3 — Serial channel 3 receive |
| Chân 69 | TXD3 — Serial channel 3 transmit |
| Chân 7 | A20 — Address bus |
| Chân 70 | RTS3 — Request To Send, channel 3 |
| Chân 71 | CTS3 — Clear To Send, channel 3 |
| Chân 72 | CD3 — Carrier Detect, channel 3 |
| Chân 73 | BRG1 — Baud-rate generator 1 output |
| Chân 74 | BRG2 — Baud-rate generator 2 output |
| Chân 75 | TA — DMA Terminal Acknowledge A |
| Chân 76 | TB — DMA Terminal Acknowledge B |
| Chân 77 | TC — Terminal Count |
| Chân 78 | DRAMC — DRAM control signals |
| Chân 79 | RAS — DRAM Row Address Strobe |
| Chân 8 | GND — Ground reference |
| Chân 80 | CAS — DRAM Column Address Strobe |
| Chân 81 | WE — DRAM Write Enable |
| Chân 82 | PA0 — Port A bit 0 |
| Chân 83 | PA1 — Port A bit 1 |
| Chân 84 | PA2 — Port A bit 2 |
| Chân 85 | PA3 — Port A bit 3 |
| Chân 86 | PA4 — Port A bit 4 |
| Chân 87 | PA5 — Port A bit 5 |
| Chân 88 | PA6 — Port A bit 6 |
| Chân 89 | PA7 — Port A bit 7 |
| Chân 9 | VCC — 5 V supply |
| Chân 90 | PB0 — Port B bit 0 |
| Chân 91 | PB1 — Port B bit 1 |
| Chân 92 | PB2 — Port B bit 2 |
| Chân 93 | PB3 — Port B bit 3 |
| Chân 94 | PB4 — Port B bit 4 |
| Chân 95 | PB5 — Port B bit 5 |
| Chân 96 | PB6 — Port B bit 6 |
| Chân 97 | PB7 — Port B bit 7 |
| Chân 98 | X1 — Crystal oscillator input |
| Chân 99 | X2 — Crystal oscillator output |
| Chân 100 | I/O — General purpose I/O pin |
Ứng dụng tiêu biểu
MC68LC302AF16CT phù hợp cho 6 Áp dụngs: ISDN Terminal Adapters, Low-End Routers and Bridges, Industrial Serial Concentrators, Legacy SCADA Controllers, Telecom Multiplexers and Channel Banks, POS and ATM Data Pumps.
ISDN Terminal Adapters
The MC68LC302AF16CT is well suited to ISDN terminal adapter designs that must terminate an ISDN Basic Rate Interface while presenting Ethernet or async serial to the user side. Its three programmable serial channels handle the two B (64 kbps) channels plus one D (16 kbps) signaling channel directly via the on-chip CPM, with HDLC/SDLC framer support for each. At 16 MHz the M68000 core runs the SPID/AOC/PPP stacks comfortably, and the integrated DRAM controller removes an external memory chip from the BOM, fitting the compact adapter footprint. The low-cost LC variant hits the consumer-grade price target without a true Ethernet MAC, which is acceptable when downstream connectivity is via USB or a separate companion chip.
Được đề xuất
Low-End Routers and Bridges
Use the MC68LC302AF16CT as the CPU in compact legacy routers, X.25-to-Ethernet bridges, and frame-relay access devices. The CPM hardware offloads bit-stuffing, CRC, and HDLC encoding for WAN serial links so the 16 MHz M68000 core spends its cycles on routing table lookups and protocol layers above layer 2. The on-chip DMA with dual channels keeps WAN-to-memory transfers moving while the CPU services the management plane. For WAN-side applications the LC variant's omission of Ethernet is a feature: design reuse is simplified because the WAN serial ports map directly without contention with on-chip MAC state. A typical design uses two channels for HDLC links to two remote sites plus the third for a local console or leased-line tail circuit.
Được đề xuất
Industrial Serial Concentrators
Deploy the MC68LC302AF16CT in industrial multi-port serial hubs that aggregate RS-232/RS-422/RS-485 field devices onto one network. The three CPM channels can each be reconfigured per port to match the attached protocol stack, and the two dedicated baud-rate generators cover the disparate rates found in plant environments. The static M68000 core allows the clock to be stalled during idle periods to meet industrial power consumption targets. The 0C to +70C commercial range matches climate-controlled cabinet enclosures. For harsher environments, the MC68LC302AFEI industrial temperature grade is the drop-in substitute. The on-chip DRAM refresh controller simplifies bill-of-materials and reduces field failure rate from external refresh logic wear.
Được đề xuất
Legacy SCADA Controllers
Apply the MC68LC302AF16CT as the supervisory controller in legacy SCADA RTUs that must interface with serial field instrumentation over HDLC or BISYNC. The CPM's hardware HDLC framer dramatically reduces CPU interrupt load compared to a software bit-banging scheme, which is essential at 16 MHz core clock. Dual-channel DMA allows the controller to copy telemetry frames between buffers without core intervention, leaving the M68000 to run the scan engine. Existing SCADA firmware written for the MC68302 family will often recompile and run on the LC variant after pin-compatibility checks, which preserves the decades of validated field logic in industrial control room deployments. The integrated DRAM controller avoids an external chip in space-constrained RTU enclosures.
Được đề xuất
Telecom Multiplexers and Channel Banks
Use the MC68LC302AF16CT in legacy TDM multiplexers, voice/digital channel banks, and E1/CEPT-1 groomers that route HDLC channels across a backplane. The triple full-duplex serial port arrangement maps cleanly to PCM bitstreams requiring multiple framed tributaries, with the CPM providing per-port HDLC formatting at line rate without CPU interference. At 16 MHz the M68000 supervisor handles supervision, alarm, and link-state machines while the CPM steers data at 2.048 Mbps per HDLC link with margin to spare. The external memory interface supports DRAM directly for frame buffering, avoiding expensive SRAM buffering in high-channel-count aggregates. The slow-clock-stop mode of the static core reduces standby power in battery-backed central office equipment.
Được đề xuất
POS and ATM Data Pumps
Design the MC68LC302AF16CT into legacy point-of-sale terminal controllers and ATM communication modules where serial protocol convergence is the dominant function. The CPM handles multiple BISYNC and async POS dialects across its three channels without an external protocol ASIC, keeping the BOM low for tier-2 retail deployments. The 8/16-bit selectable bus lets designers use 8-bit wide EPROMs to minimize the production cost while preserving the option to upgrade to 16-bit flash for in-field firmware updates. Industry-standard m68k toolchains (gcc cross-compiler and gdb debugger) remain available, keeping engineering costs low for long-life terminals that may remain in service for 10-20 years.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC68LC302AF16CT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC68302FC16 | MC68LC302AFEI | MC68EN360RC25 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 100-LQFP (14x14mm) | 100-LQFP - same | 100-LQFP - same | 100-LQFP - same |
| Core Architecture | M68000 (m68k) at 16 MHz | M68000 at 16 MHz | M68000 at 16 MHz | ColdFire CPU32+ at 25 MHz |
| Bus Width | 8/16-bit selectable | 8/16-bit selectable | 8/16-bit selectable | 32-bit |
| Number of Serial Channels | 3 full-duplex | 3 or more (model-dependent) | 3 full-duplex | 2 SCC + 2 SMC |
| On-chip Ethernet MAC | No (LC variant) | Yes | No | Yes (10 Mbps) |
| On-chip DMA | Yes (2-channel) | Yes (2-channel) | Yes (2-channel) | Yes (2-channel) |
| Operating Frequency | 16 MHz | 16 MHz | 16 MHz | 25 MHz |
Bảo phân biệt quan trọng
- No on-chip Ethernet MAC - cost-reduced feature set (vsMC68302FC16)
- Same legacy 16 MHz M68000 core as the rest of the family (vsMC68EN360RC25)
- Static M68000 core with clock-stop idle mode (vsMC68LC302AFEI (industrial temp variant))
Ghi chú thiết kế
Bus-width configuration (D8/D16 mode) is selected at reset by the sampled state of the DATA15/D15 pin during reset de-assertion. A 16-bit bus must see a known-good HIGH on the D15 strap pull-up; a 10 kohm pull-up is recommended. Forgetting this strap causes the part to boot in 8-bit mode and reject 16-bit accesses, an often-misdiagnosed boot failure. Confirm the strap value with your reset supervisor's idle state.
The 100-LQFP at 14x14mm requires 0.5 mm pitch PCB traces, which most PCB manufacturers can produce reliably with 4 mil traces. Decoupling requires at least 4 ceramic capacitors (0.1 uF) placed within 2 mm of the four VCC clusters of the package. For DRAM-interface designs using the on-chip controller, place a 100 nF cap directly on each DRAM bank to suppress simultaneous switching noise during row activations.
The MC68LC302 has no on-chip Ethernet; if your application bridges to a LAN, you must add an external Ethernet controller (e.g. the legacy MC68160) and tie it into a CPM serial channel. Designers migrating from the MC68302 family often need to de-initialize the original Ethernet MAC block in firmware to match the LC derivative - skipping this step leaves registers configured for nonexistent hardware and may hang I/O initialization.
Thông tin tuân thủ
Component is EOL ('Not For New Designs'); modern compliance certifications such as RoHS/REACH are not always carried through to legacy m68k packaging. RoHS status for this exact part is not explicitly stated in the verified distributor records. AEC-Q100 automotive qualification does not apply to this legacy industrial MPU - for new automotive designs migrate to a current device.
