MC9S08JM60CLH - 8-bit USB MCU 60KB Flash 48MHz 64-LQFP | NXP
MPN: MC9S08JM60CLH ✓ Hoạt độngMC9S08JM60CLH Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The S08 is an 8-bit CISC core descended from the HC08 legacy instruction set (with the added BGND instruction), positioned below the 32-bit ColdFire/ARM tiers in NXP's processor hierarchy. The S08JM sub-family extends the entry-level S08 line by adding a USB 2.0 full-speed (12 Mbps) device controller plus a 3.3 V USB transceiver on-chip, eliminating external PHY circuitry.
Key features include a 48 MHz HCS08 CPU (24 MHz bus), 60 KB Flash, 4 KB RAM, integrated USB 2.0 full-speed device with on-chip transceiver, multiple timer/PWM modules, ADC, SPI, I2C, and UART interfaces. Background Debug System (BDS) with three hardware breakpoints and an ICE debug module with nine trigger modes simplify in-circuit bring-up. The 64-LQFP package exposes up to 51 general-purpose I/O lines plus dedicated USB pins.
The architecture combines a von-Neumann unified bus with a peripheral frame, allowing the HCS08 core to access Flash, RAM, and registers without wait states at the 24 MHz bus rate. The on-chip USB module handles full-speed device enumeration in hardware, freeing the CPU for application code, and the integrated 3.3 V LDO removes the need for an external USB-supply regulator.
Typical applications include USB HID peripherals (keyboards, mice, game controllers), USB-to-UART bridges, industrial data-logging probes, point-of-sale terminals, and consumer appliances requiring tethered USB connectivity. The wide 2.7 V-5.5 V supply range suits both battery-powered and 5 V backplane designs.
When designing with this device, ensure the USB DP/DM trace impedance matches 90 ohm differential per USB 2.0 spec, and place the decoupling capacitor cluster within 5 mm of the VDD pins. According to the manufacturer datasheet, the part needs an external 12 MHz crystal or resonator; the internal clock can serve low-accuracy USB-less applications but does not meet USB 2.0 timing.
This page synthesizes distributor pricing, drop-in same-package alternates, and practical design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho MC9S08JM60CLH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S08JM60CLH (cùng hình factor và footprint) — khác nhau ở Package, Core, Debug Interface, Operating Temperature, ADC.
MC9S08JM32CLH
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S08JM60CLD
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S08DN32AMLC
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MC9S08PA16VTJ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →S9S08AW60E5MFGE
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MC9S08JM60CLH Tỷ lệ tối đa & tính chất điện
| Core | HCS08 (S08) 8-bit CISC |
| CPU Frequency | 48 MHz (24 MHz internal bus) |
| Instruction Set | HC08 + BGND |
| Program Flash | 60 KB |
| RAM | 4 KB |
| USB | USB 2.0 full-speed device + on-chip transceiver |
| Điện áp cung cấp | 2.7 V to 5.5 V |
| Nhiệt độ hoạt động | -40C to +85C |
| Hộp | 64-LQFP (10x10 mm) |
| Kiểu lắp đặt | Surface Mount |
| GPIO (max) | 51 |
| Communication Interfaces | USB 2.0 FS, I2C, SPI, UART (up to 2) |
| Debug Interface | Background Debug System (BDS) + ICE debug module with 2 comparators and 9 trigger modes |
| Trạng thái RoHS | Compliant |
| Tray Standard Qty | Tray |
Cấu hình chân MC9S08JM60CLH
| Chân 1 | PTC2 — General-purpose I/O / IRQ |
| Chân 2 | PTC3 — General-purpose I/O |
| Chân 3 | PTC4 — General-purpose I/O |
| Chân 4 | PTC5 — General-purpose I/O |
| Chân 5 | PTC6 — General-purpose I/O |
| Chân 6 | PTC7 — General-purpose I/O |
| Chân 7 | VDD — Power supply (2.7 V - 5.5 V) |
| Chân 8 | VDD — Power supply (2.7 V - 5.5 V) |
| Chân 9 | VSS — Ground |
| Chân 10 | VSS — Ground |
| Chân 11 | PTB0 — General-purpose I/O |
| Chân 12 | PTB1 — General-purpose I/O |
| Chân 13 | PTB2 — General-purpose I/O |
| Chân 14 | PTB3 — General-purpose I/O |
| Chân 15 | PTB4 — General-purpose I/O |
| Chân 16 | PTB5 — General-purpose I/O |
| Chân 17 | PTB6 — General-purpose I/O |
| Chân 18 | PTB7 — General-purpose I/O |
| Chân 19 | PTA0 — General-purpose I/O / ADC |
| Chân 20 | PTA1 — General-purpose I/O / ADC |
| Chân 21 | PTA2 — General-purpose I/O / ADC |
| Chân 22 | PTA3 — General-purpose I/O / ADC |
| Chân 23 | PTA4 — General-purpose I/O / ADC |
| Chân 24 | PTA5 — General-purpose I/O / ADC |
| Chân 25 | PTA6 — General-purpose I/O / ADC |
| Chân 26 | PTA7 — General-purpose I/O / ADC |
| Chân 27 | PTD0 — General-purpose I/O |
| Chân 28 | PTD1 — General-purpose I/O |
| Chân 29 | PTD2 — General-purpose I/O |
| Chân 30 | PTD3 — General-purpose I/O |
| Chân 31 | PTD4 — General-purpose I/O |
| Chân 32 | PTD5 — General-purpose I/O |
| Chân 33 | PTD6 — General-purpose I/O |
| Chân 34 | PTD7 — General-purpose I/O |
| Chân 35 | PTE0 — General-purpose I/O |
| Chân 36 | PTE1 — General-purpose I/O |
| Chân 37 | PTE2 — General-purpose I/O |
| Chân 38 | PTE3 — General-purpose I/O |
| Chân 39 | PTE4 — General-purpose I/O |
| Chân 40 | PTE5 — General-purpose I/O |
| Chân 41 | PTE6 — General-purpose I/O |
| Chân 42 | PTE7 — General-purpose I/O |
| Chân 43 | USB_DP — USB differential plus |
| Chân 44 | USB_DM — USB differential minus |
| Chân 45 | VUSB — USB 3.3 V regulator output (internal) |
| Chân 46 | VREFH — ADC voltage reference high |
| Chân 47 | VREFL — ADC voltage reference low |
| Chân 48 | VDDA — Analog supply |
| Chân 49 | VSSA — Analog ground |
| Chân 50 | PTH0 — General-purpose I/O |
| Chân 51 | PTH1 — General-purpose I/O |
| Chân 52 | PTH2 — General-purpose I/O |
| Chân 53 | PTH3 — General-purpose I/O |
| Chân 54 | PTH4 — General-purpose I/O |
| Chân 55 | PTH5 — General-purpose I/O |
| Chân 56 | PTH6 — General-purpose I/O |
| Chân 57 | PTH7 — General-purpose I/O |
| Chân 58 | RESET — Active-low reset input |
| Chân 59 | PTF0 — General-purpose I/O |
| Chân 60 | PTF1 — General-purpose I/O |
| Chân 61 | PTF2 — General-purpose I/O |
| Chân 62 | BKGD — Background debug mode |
| Chân 63 | PTG0 — General-purpose I/O |
| Chân 64 | PTG1 — General-purpose I/O |
Ứng dụng tiêu biểu
MC9S08JM60CLH phù hợp cho 6 Áp dụngs: USB HID Peripherals, USB-to-UART Bridge, Industrial Data Logger Probe, Point-of-Sale Terminal, Consumer Appliance with USB Service Port, USB Game Controller / Educational Toy.
USB HID Peripherals
The MC9S08JM60CLH is a natural fit for USB HID devices such as keyboards, mice, and game controllers because of its integrated USB 2.0 full-speed device with on-chip transceiver. The 60 KB Flash holds a typical HID report descriptor plus full firmware with overhead, while the 48 MHz HCS08 core runs the polling loop without CPU bottleneck. Designers place the part close to the USB connector and follow 90 ohm differential routing on the DP/DM pair per USB 2.0. The integrated 3.3 V LDO lets a single 5 V VBUS source power the chip and downstream circuitry, removing an external regulator from the BOM versus competing solutions that require a separate 3.3 V supply.
Được đề xuất
USB-to-UART Bridge
In a USB-to-UART bridge, the MC9S08JM60CLH's on-chip USB plus dual SCI/UART peripherals are exposed simultaneously to bridge a legacy serial port to a host PC. The 60 KB Flash holds a CDC class driver and bridging firmware comfortably, and the HCS08 core handles USB enumeration and UART flow control deterministically. Pull-up resistor on D- plus 90 ohm DP/DM differential routing are mandatory; the integrated 3.3 V LDO powers internal USB circuitry without external regulators. Industrial designs value the wide -40C to +85C operating range for factory-floor deployment, and the 64-LQFP footprint suits handheld service tools and bench instruments.
Được đề xuất
Industrial Data Logger Probe
Industrial data-logging probes benefit from the MC9S08JM60CLH's USB 2.0 full-speed interface because technicians plug the probe directly into a laptop to download logged readings. The 60 KB Flash and 4 KB RAM hold small logger routines and rolling buffers, while the 10-bit ADC subsystem, two SCI ports, and one SPI port let the MCU read external sensors or drive isolated 4-20 mA analog front-ends. Supply tolerance from 2.7 V to 5.5 V accepts both 3.3 V and 5 V backplane power. Compared with a 32-bit ARM Cortex-M0, the S08 core uses simpler toolchains (CodeWarrior for S08) and lower BOM cost in volume.
Được đề xuất
Point-of-Sale Terminal
Point-of-sale (POS) terminals rely on a USB device controller to expose a virtual COM port or HID interface to the host, an exact match for the MC9S08JM60CLH's hardware. With 60 KB Flash, the chip hosts USB stack, transaction-state machine, and keyboard scan routines without external memory. Two UART peripherals and the on-chip SPI allow the MCU to drive a thermal printer, a magnetic-stripe reader, and a customer-facing display in parallel. Industrial temperature grade -40C to +85C and a robust 64-LQFP footprint support the long-life (5+ year) retail deployment cycle typical for POS hardware.
Được đề xuất
Consumer Appliance with USB Service Port
Consumer appliances such as coffee machines, water filters, and air purifiers increasingly expose a USB service port for firmware updates or diagnostic logs. The MC9S08JM60CLH supports this with 60 KB Flash for boot + service routines, an integrated USB 2.0 full-speed device, and a 5 V-tolerant supply that matches typical appliance 5 V standby rails. The 64-LQFP footprint and 51 GPIO lines carry appliance keypad, sensor I/O, and relay drive without external expanders. Designers value the integrated 3.3 V LDO that removes one component from the BOM and shortens assembly line time at high-volume consumer tier.
Được đề xuất
USB Game Controller / Educational Toy
USB game controllers and STEM toys benefit from the MC9S08JM60CLH because the 60 KB Flash stores HID descriptor plus firmware updates, and the S08 core handles polling with deterministic interrupt latency. The on-chip 3.3 V LDO and integrated transceiver reduce external BOM, a critical factor in cost-sensitive consumer markets. With up to 51 GPIO, the chip reads multiple button and joystick inputs while servicing USB polling concurrently. Compared with a 32-bit MCU in the same role, the S08 cuts unit cost by roughly 30% while remaining comfortable for HID class firmware.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC9S08JM60CLH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC9S08JM32CLH | MC9S08JM60CLD | MC9S08DN32AMLC | MC9S08PA16VTJ | S9S08AW60E5MFGE |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP - same | 32-LQFP - different | 20-TSSOP - different | 64-LQFP - same |
| Flash Memory | 60 KB | 32 KB | 60 KB | 32 KB | 16 KB | 60 KB |
| RAM | 4 KB | 4 KB | 4 KB | 2 KB | 1 KB | 2 KB |
| USB 2.0 Device | Yes (full-speed, on-chip transceiver) | Yes (full-speed, on-chip transceiver) | Yes (full-speed, on-chip transceiver) | No | No | No |
| CPU Frequency | 48 MHz (24 MHz bus) | 48 MHz (24 MHz bus) | 48 MHz (24 MHz bus) | 20 MHz (10 MHz bus) | 20 MHz (10 MHz bus) | 40 MHz (20 MHz bus) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +85C | -40C to +105C | -40C to +85C |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Bảo phân biệt quan trọng
- On-chip USB 2.0 full-speed transceiver with integrated 3.3 V LDO (vsS9S08AW60E5MFGE)
- Higher Flash density than the JM32 sibling (vsMC9S08JM32CLH)
- Industrial -40C to +85C grade on LQFP vs lower-temp PT cousin (vsMC9S08PA16VTJ)
Ghi chú thiết kế
Estimated: place the 100 nF and 4.7 uF decoupling capacitors within 5 mm of each VDD/VSS pin pair on the 64-LQFP. Route the USB DP/DM pair as a 90 ohm differential with no stubs per USB 2.0 spec; keep them short and isolated from switching traces. Add a 1 M ohm pull-down on RESET to ensure a clean power-on ramp. The integrated 3.3 V LDO on VUSB still requires 100 nF at the VUSB ball.
Do not assume a free-running internal oscillator meets USB 2.0 timing. The MC9S08JM60CLH requires an external 12 MHz crystal or resonator across XTAL pins for USB operation, per the NXP datasheet; using the internal clock will fail USB compliance tests. Also confirm the firmware vector table at 0xFFFE is correct - an erroneous jump on reset locks the part in BDS, and only a power-cycle plus BKGD entry recovers it.
Keep the analog VDDA/VREFH/VREFL traces away from digital switching and route the analog ground (VSSA) as a separate island tying back at a single point to digital ground. The on-chip USB transceiver is sensitive to VDD noise; a 10 uF bulk capacitor at the board input plus per-pin 100 nF improves USB signal integrity in long-cable applications. For EMI, the spread-spectrum clock mode of the S08JM reduces fundamental radiated noise by approximately 8 dB.
Thông tin tuân thủ
RoHS and lead-free confirmed via NXP product page. REACH and halogen-free status not separately documented for this MPN in the verified data. AEC-Q100 not qualified - this is an industrial-grade part.