MC9S08LC60LH - 8-bit S08 MCU, 60KB Flash, LCD, USB, CAN | NXP
MPN: MC9S08LC60LH ✓ Hoạt độngMC9S08LC60LH Tóm tắt
An 8-bit MCU (microcontroller unit) is a single-chip computer that integrates a CPU, memory, and peripherals on one die. The HCS08 core is a von-Neumann 8-bit CPU executed from a common Flash/ROM address space, designed for predictable interrupt latency and ultra-low standby power. Microcontrollers sit at the foundation of every embedded system; 8-bit variants are favored when cost, deterministic behavior, and peripheral integration (LCD, USB, CAN) outweigh raw compute throughput.
Key features of the MC9S08LC60LH include 60 KB on-chip Flash, 4 KB RAM, an internal LCD driver with up to 8 backplanes and configurable segment count, a USB 2.0 full-speed device controller, a CAN 2.0 A/B module, two SCI, one SPI, and up to 18 GPIO pins. The CPU runs up to 40 MHz (20 MHz bus) from a 1.8 V to 3.6 V supply, supporting both lithium-cell and 3.3 V regulated rails.
Architecturally, the S08LC uses the HCS08 instruction set (object-code compatible with HC08 plus BGND for debugging), a 3-stage pipeline, and a multi-tier clock gating scheme that allows peripherals to be gated individually during STOP modes. The integrated LCD charge pump supports both glass types and contrast over temperature.
Typical applications include metering and instrumentation, medical devices, white-goods HMIs, industrial control panels, and consumer products requiring segment-LCD displays with USB connectivity. The CAN interface makes it attractive in automotive body and appliance networks.
When designing with this part, allocate PCB area for the LCD segment pins (which form a large portion of the LQFP-64 ballout) and place the external 32.768 kHz crystal close to the XTAL pins to minimize stray capacitance.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho MC9S08LC60LH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S08LC60LH (cùng hình factor và footprint) — khác nhau ở Instruction Set, Package.
MC9S08LC36LH
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S08LC60LC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08LC60LK
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MC9S08LC60LH Tỷ lệ tối đa & tính chất điện
| Core | HCS08 (8-bit) |
| CPU Frequency | 40 MHz (20 MHz bus) |
| Program Memory | 60 KB Flash |
| RAM | 4 KB |
| Điện áp cung cấp | 1.8 V to 3.6 V |
| LCD Controller | Integrated (up to 8 backplanes) |
| USB | USB 2.0 Full-Speed Device |
| CAN | CAN 2.0 A/B |
| SCI / UART | 2 |
| SPI | 1 |
| GPIO Count | 18 |
| Hộp | 64-pin LQFP (10x10 mm, 0.5 mm pitch) |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân MC9S08LC60LH
| Chân 1 | PTC2 — General-purpose I/O / LCD segment |
| Chân 2 | PTC3 — General-purpose I/O / LCD segment |
| Chân 3 | PTC4 — General-purpose I/O / LCD segment |
| Chân 4 | PTC5 — General-purpose I/O / LCD segment |
| Chân 5 | PTC6 — General-purpose I/O / LCD segment |
| Chân 6 | PTC7 — General-purpose I/O / LCD segment |
| Chân 7 | VDD — Supply voltage (1.8 V to 3.6 V) |
| Chân 8 | VSS — Ground |
| Chân 9 | XTAL1 — Crystal oscillator input / external clock |
| Chân 10 | XTAL2 — Crystal oscillator output |
| Chân 11 | RESET — Reset input (active low) |
| Chân 12 | BKGD — Background debug mode / MOD communication |
| Chân 13 | PTA0 — General-purpose I/O |
| Chân 14 | PTA1 — General-purpose I/O / SCI Tx |
| Chân 15 | PTA2 — General-purpose I/O / SCI Rx |
| Chân 16 | PTA3 — General-purpose I/O |
| Chân 17 | PTA4 — General-purpose I/O |
| Chân 18 | PTA5 — General-purpose I/O |
| Chân 19 | VUSB — USB regulator bypass / VUSB cap |
| Chân 20 | USB_DP — USB D+ data line |
| Chân 21 | USB_DM — USB D- data line |
| Chân 22 | VSS — Ground |
| Chân 23 | VDD — Supply voltage |
| Chân 24 | CAN_TX — CAN transmit output |
| Chân 25 | CAN_RX — CAN receive input |
| Chân 26 | PTB0 — General-purpose I/O / LCD segment |
| Chân 27 | PTB1 — General-purpose I/O / LCD segment |
| Chân 28 | PTB2 — General-purpose I/O / LCD segment |
| Chân 29 | PTB3 — General-purpose I/O / LCD segment |
| Chân 30 | PTB4 — General-purpose I/O / LCD segment |
| Chân 31 | PTB5 — General-purpose I/O / LCD segment |
| Chân 32 | PTB6 — General-purpose I/O / LCD segment |
| Chân 33 | PTB7 — General-purpose I/O / LCD segment |
| Chân 34 | LCD_P0 — LCD backplane 0 |
| Chân 35 | LCD_P1 — LCD backplane 1 |
| Chân 36 | LCD_P2 — LCD backplane 2 |
| Chân 37 | LCD_P3 — LCD backplane 3 |
| Chân 38 | LCD_P4 — LCD backplane 4 |
| Chân 39 | LCD_P5 — LCD backplane 5 |
| Chân 40 | LCD_P6 — LCD backplane 6 |
| Chân 41 | LCD_P7 — LCD backplane 7 |
| Chân 42 | PTD0 — General-purpose I/O / LCD segment |
| Chân 43 | PTD1 — General-purpose I/O / LCD segment |
| Chân 44 | PTD2 — General-purpose I/O / LCD segment |
| Chân 45 | PTD3 — General-purpose I/O / LCD segment |
| Chân 46 | PTD4 — General-purpose I/O / LCD segment |
| Chân 47 | PTD5 — General-purpose I/O / LCD segment |
| Chân 48 | PTD6 — General-purpose I/O / LCD segment |
| Chân 49 | PTD7 — General-purpose I/O / LCD segment |
| Chân 50 | PTE0 — General-purpose I/O / LCD segment |
| Chân 51 | PTE1 — General-purpose I/O / LCD segment |
| Chân 52 | PTE2 — General-purpose I/O / LCD segment |
| Chân 53 | PTE3 — General-purpose I/O / LCD segment |
| Chân 54 | PTE4 — General-purpose I/O / LCD segment |
| Chân 55 | PTE5 — General-purpose I/O / LCD segment |
| Chân 56 | PTE6 — General-purpose I/O / LCD segment |
| Chân 57 | PTE7 — General-purpose I/O / LCD segment |
| Chân 58 | PTF0 — General-purpose I/O / LCD segment |
| Chân 59 | PTF1 — General-purpose I/O / LCD segment |
| Chân 60 | PTF2 — General-purpose I/O / LCD segment |
| Chân 61 | PTF3 — General-purpose I/O / LCD segment |
| Chân 62 | PTF4 — General-purpose I/O / LCD segment |
| Chân 63 | PTF5 — General-purpose I/O / LCD segment |
| Chân 64 | PTF6 — General-purpose I/O / LCD segment |
Ứng dụng tiêu biểu
MC9S08LC60LH phù hợp cho 6 Áp dụngs: Electricity Metering with Segment LCD, Industrial Control Panel HMI, Medical Infusion Pump User Interface, White Goods Control Board (Washing Machine / Oven), USB Diagnostic / Field-Service Tool, Consumer Remote / Sensor Display.
Electricity Metering with Segment LCD
The MC9S08LC60LH is engineered for single-phase and multi-rate electricity meters where a segment-LCD display, low STOP-mode power, and a reliable communication interface are mandatory. Its 60 KB Flash holds DLMS/COSEM or IEC 62056 protocol stacks plus metrology compensation tables, while the on-chip LCD controller drives up to 8 backplanes directly without an external driver. The 1.8 V minimum supply lets the meter run from a single-cell lithium backup during line-power loss, and the integrated CAN or SCI front-ends talk to data concentrators.
Được đề xuất
Industrial Control Panel HMI
In factory-floor control panels and machine-status displays, the MC9S08LC60LH combines its segment-LCD driver, two SCI channels, and CAN 2.0 interface to update alphanumeric status without a graphics LCD. The 40 MHz HCS08 CPU refreshes 8-backplane LCDs at low duty cycles to keep average current below 5 mA active, and the CAN module ties into industrial fieldbuses for live I/O feedback. Robust STOP modes with RTC wake let the panel sleep between operator interactions, extending battery life in portable variants.
Được đề xuất
Medical Infusion Pump User Interface
Medical infusion pumps and point-of-care analyzers benefit from the MC9S08LC60LH's deterministic HCS08 interrupt latency, integrated segment-LCD for dosage and alarm readouts, and USB 2.0 full-speed device port for clinician-side configuration and log download. The 64-pin LQFP exposes enough GPIO to scan keypads while the LCD controller displays flow-rate digits and warning icons simultaneously, with the CAN channel reserved for inter-module communication in bed-side monitor racks.
Được đề xuất
White Goods Control Board (Washing Machine / Oven)
The MC9S08LC60LH is well-suited for washing-machine and oven control boards that need a robust HMI and simple motor-control signaling. Its segment-LCD shows cycle state and timer digits, the SCI interfaces to the motor inverter, and 18 GPIO lines scan the rotary encoder plus tactile keys. Operating from 1.8 V to 3.6 V reduces regulator cost in 3.3 V appliance rails, and STOP modes with RTC wake let the board idle when not in use.
Được đề xuất
USB Diagnostic / Field-Service Tool
Diagnostic tools that connect to a host PC over USB while also bridging to a CAN or RS-485 industrial network are a clean fit for the MC9S08LC60LH, which integrates USB 2.0 FS device, CAN 2.0 A/B, and two SCI/UART channels on one die. 60 KB Flash accommodates USB-CDC plus a small vendor protocol, the segment-LCD provides status without needing a full graphics display, and the 1.8 V minimum supply allows single-cell Li-ion power.
Được đề xuất
Consumer Remote / Sensor Display
Consumer electronics with a small segment-LCD (thermostats, weighing scales, sensor readouts, smart-home keypads) benefit from the MC9S08LC60LH's deep STOP modes, low BOM count, and integrated USB for setup. The HCS08 core is fast enough for basic FSM control, and the on-chip LCD controller eliminates external drivers, keeping the bill of materials under one dollar for the display subsystem on a multi-million-unit product.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC9S08LC60LH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC9S08LC36LH | MC9S08LC60LC | MC9S08LC60LK |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same |
| Flash Memory | 60 KB | 36 KB | 60 KB | 60 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB |
| CPU Core | HCS08, 40 MHz | HCS08, 40 MHz - same | HCS08, 40 MHz - same | HCS08, 40 MHz - same |
| LCD Controller | Integrated (8 backplanes) | Integrated (8 backplanes) - same | Integrated (8 backplanes) - same | Integrated (8 backplanes) - same |
| USB | USB 2.0 FS Device | USB 2.0 FS Device - same | USB 2.0 FS Device - same | USB 2.0 FS Device - same |
| CAN | CAN 2.0 A/B | CAN 2.0 A/B - same | CAN 2.0 A/B - same | CAN 2.0 A/B - same |
| Supply Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V - same | 1.8 V to 3.6 V - same | 1.8 V to 3.6 V - same |
Bảo phân biệt quan trọng
- Integrated segment-LCD controller eliminates external LCD driver (vsMC9S08GB60ACFUE)
- 60 KB Flash supports larger USB and CAN protocol stacks (vsMC9S08LC36LH)
- 1.8 V minimum supply enables single-cell lithium operation (vsOther 8-bit MCUs starting at 2.7 V)
- Hardware interrupt controller with up to 32 sources (vsBaseline HCS08 devices with 16 interrupts)
Ghi chú thiết kế
Decouple VDD/VSS pairs with a 100 nF ceramic capacitor placed within 3 mm of each supply pin and a bulk 4.7 uF tantalum or ceramic on the main VDD rail. For USB operation, populate VUSB with a 1 uF ceramic and avoid running digital traces under the USB_DM/USB_DP pair. In STOP1 mode, draw under 1 uA while keeping the LCD charge pump active - useful for battery-backed metering.
Route the XTAL1/XTAL traces symmetrically with 50 ohm characteristic impedance and keep their ground island isolated from the noisy LCD backplane return. Place the 32.768 kHz crystal within 5 mm of the XTAL pins with a guard ring to GND. Avoid right-angle traces and via transitions on the crystal path; each stray pF adds startup jitter to the LCD frame-rate and degrades RTC accuracy.
Estimated: total LCD segment I/O count is roughly 8 backplanes x up to 40 segments, so route all segment lines on the top layer and stitch through vias only at the IC pads. Use a low-pass RC filter (10 kohm + 100 pF) on each segment if the glass is located more than 50 mm from the MCU to suppress EMI. Keep CAN bus traces short and matched; pair terminator resistors of 120 ohm are recommended at the bus ends only.
Do not enable both USB and CAN interrupts without configuring their priority order, or CAN frame loss can occur during heavy USB enumeration. The BKGD pin shares its function with the MOD (mode) entry signal - never tie it directly to GND through a low-impedance path, or background debug becomes inaccessible. VUSB must reach at least 3.0 V for USB transceiver compliance; a weak LDO will fail USB-IF eye-pattern tests.
Thông tin tuân thủ
Specific RoHS / REACH / lead-free status was not present in the retrieved web data; consult the NXP product page environmental documentation before high-volume commitment. AEC-Q100 qualification not found in data; the LC60LH family is typically aimed at industrial and appliance markets.
