MC9S08PA60VLF-FR - 60KB Flash 8-bit S08 MCU | NXP LQFP-48
MPN: MC9S08PA60VLF-FR ✓ Hoạt độngMC9S08PA60VLF-FR Tóm tắt
An 8-bit MCU (microcontroller unit) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals such as timers, ADCs, and communication interfaces. The S08 core family uses the Freescale/NXP S08 instruction set, an enhanced evolution of the HC08 architecture, with a 16-bit address space and on-chip hardware multiply/divide. Within the broader taxonomy, the S08PA sits as: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. This part targets cost-sensitive embedded designs that require 5 V tolerance, robust ESD/EFT immunity, and a scalable peripheral set across the S08P family.
Key features of the MC9S08PA60VLF-FR include a 12-channel 12-bit ADC, an analog comparator with internal 6-bit DAC reference, up to three timers including a 2-channel FlexTimer (FTM) with motor-control capability, up to two SCI (UART) modules, and one SPI. Internal 1 kHz LPO and 4–20 MHz ICS oscillators remove the need for an external crystal in many designs. The 48-LQFP pin-out exposes up to 39 GPIO with programmable drive strength, slew-rate control, and interrupt-on-edge. Hardware CRC, watchdog, and low-voltage detect improve functional safety.
Typical applications include motor control (small BLDC and brushed DC drivers), home appliances and white goods, industrial control modules, lighting control, point-of-load control, and consumer electronics user interfaces. The wide 5 V supply tolerance makes it well suited for legacy 5 V rails in industrial plants and automotive body modules (non-safety sub-systems).
When designing, ensure the VDD decoupling network (100 nF + 4.7 µF) is placed within 5 mm of the pins, route the ICS oscillator traces as guarded differential pairs, and avoid routing analog ADC channels across switching node return paths. The on-chip EEPROM with built-in charge pump supports in-application byte erase/write without external hardware.
This page synthesizes NXP distributor pricing, same-family drop-in alternatives, and practical design notes that complement the manufacturer datasheet by enabling quick sourcing and footprint decisions.
Bộ thay thế dễ dàng lắp đặt cho MC9S08PA60VLF-FR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S08PA60VLF-FR (cùng hình factor và footprint) — khác nhau ở ADC, Package, Timers, EEPROM, SRAM.
MC9S08PA60VLF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08PA32VLH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08PA16VLH
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08PT32VLF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F46K22-I/P
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S08PA60VLF-FR Tỷ lệ tối đa & tính chất điện
| Core | S08 (8-bit HCS08 family) |
| Program Flash | 60 KB |
| SRAM | 4 KB |
| EEPROM | 256 bytes |
| Maximum Bus Frequency | 20 MHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40 °C to +105 °C |
| ADC | 12-channel, 12-bit |
| Analog Comparator | 1 (with internal 6-bit DAC reference) |
| FlexTimer (FTM) | 2 channels (motor-control timer) |
| Timers | Up to 3 (FTM + TPM + PIT/MTIM) |
| SCI (UART) Modules | Up to 2 |
| SPI Modules | 1 |
| GPIO (max) | 39 |
| Hộp | 48-LQFP (7 x 7 mm) |
| Kiểu lắp đặt | Surface Mount |
| ESD Performance | EFT/ESD robust (S08P family rated) |
| Trạng thái RoHS | Compliant |
| Lead-Free | Yes |
Cấu hình chân MC9S08PA60VLF-FR
| Chân 1 | PTD0/KBI0 — Port D bit 0; KBI input 0 |
| Chân 2 | PTD1/KBI1 — Port D bit 1; KBI input 1 |
| Chân 3 | PTD2/KBI2 — Port D bit 2; KBI input 2 |
| Chân 4 | PTD3/KBI3 — Port D bit 3; KBI input 3 |
| Chân 5 | VDD — MCU power supply (2.7 V to 5.5 V) |
| Chân 6 | VSS — Ground reference |
| Chân 7 | PTC0 — Port C bit 0; ADC channel 0 / FTM channel 0 |
| Chân 8 | PTC1 — Port C bit 1; ADC channel 1 / FTM channel 1 |
| Chân 9 | PTC2 — Port C bit 2; ADC channel 2 |
| Chân 10 | PTC3 — Port C bit 3; ADC channel 3 |
| Chân 11 | PTC4 — Port C bit 4; ADC channel 4 |
| Chân 12 | PTC5 — Port C bit 5; ADC channel 5 |
| Chân 13 | PTC6 — Port C bit 6; ADC channel 6 |
| Chân 14 | PTC7 — Port C bit 7; ADC channel 7 |
| Chân 15 | PTB0/ADP0 — Port B bit 0; ADC channel 8 |
| Chân 16 | PTB1/ADP1 — Port B bit 1; ADC channel 9 |
| Chân 17 | PTB2/ADP2 — Port B bit 2; ADC channel 10 |
| Chân 18 | PTB3/ADP3 — Port B bit 3; ADC channel 11 |
| Chân 19 | VDD — MCU power supply (tied to pin 5) |
| Chân 20 | VSS — Ground (tied to pin 6) |
| Chân 21 | PTA0 — Port A bit 0 |
| Chân 22 | PTA1 — Port A bit 1 |
| Chân 23 | PTA2 — Port A bit 2 |
| Chân 24 | PTA3 — Port A bit 3 |
| Chân 25 | PTA4 — Port A bit 4 |
| Chân 26 | PTA5 — Port A bit 5 |
| Chân 27 | PTA6 — Port A bit 6 |
| Chân 28 | PTA7 — Port A bit 7 |
| Chân 29 | TCLK/RESET_b — TCLK / active-low reset input |
| Chân 30 | PTE0/TXD1 — Port E bit 0; SCI1 transmit |
| Chân 31 | PTE1/RXD1 — Port E bit 1; SCI1 receive |
| Chân 32 | PTE2/TXD2 — Port E bit 2; SCI2 transmit |
| Chân 33 | PTE3/RXD2 — Port E bit 3; SCI2 receive |
| Chân 34 | PTE4/MOSI — Port E bit 4; SPI MOSI |
| Chân 35 | PTE5/MISO — Port E bit 5; SPI MISO |
| Chân 36 | PTE6/SPSCK — Port E bit 6; SPI clock |
| Chân 37 | PTE7/SS_b — Port E bit 7; SPI active-low slave select |
| Chân 38 | BKGD/MS — Background debug mode / mode select |
| Chân 39 | PTF0 — Port F bit 0 |
| Chân 40 | PTF1 — Port F bit 1 |
| Chân 41 | PTF2 — Port F bit 2 |
| Chân 42 | PTF3 — Port F bit 3 |
| Chân 43 | PTF4 — Port F bit 4 |
| Chân 44 | PTF5 — Port F bit 5 |
| Chân 45 | EXTAL — External clock/crystal input |
| Chân 46 | XTAL — External clock/crystal output |
| Chân 47 | VDD — MCU power supply (tied to pins 5 & 19) |
| Chân 48 | VSS — Ground (tied to pins 6 & 20) |
Ứng dụng tiêu biểu
MC9S08PA60VLF-FR phù hợp cho 7 Áp dụngs: Small BLDC / Brushed DC Motor Control, White Goods / Home Appliance Control, Industrial Lighting Control (DALI / 0-10 V / LED Driver), Point-of-Load / Multi-Rail Power Control, Consumer Electronics User Interface (HMI / Keypad / LCD), Battery-Operated Sensor Modules, Industrial Sensor Conditioning / 4-20 mA Loop.
Small BLDC / Brushed DC Motor Control
The MC9S08PA60VLF-FR's hardware FlexTimer (FTM) with complementary PWM outputs, dead-time insertion, and fault inputs makes it well-suited to small BLDC and brushed DC motor drives. Its 2.7 V to 5.5 V supply range tolerates 5 V industrial rails, and the on-chip analog comparator delivers sub-microsecond overcurrent detection for cycle-by-cycle current limiting. The 12-bit ADC samples back-EMF or phase currents with sufficient resolution for trapezoidal commutation in pumps, fans, and small appliances.
Được đề xuất
White Goods / Home Appliance Control
Washing machines, dishwashers, refrigerators, and induction cooktops demand EFT/ESD-robust 5 V MCUs that ride directly on legacy appliance rails. The S08PA family inside the MC9S08PA60VLF-FR brings reinforced ESD/EFT immunity and a wide -40 °C to +105 °C operating range, allowing designers to skip external TVS in most user-interface boards. The dual SCI channels simplify isolation between power-stage and HMI controllers, while the 256-byte EEPROM stores user-settable programs (cook profiles, spin modes) without external NVM.
Được đề xuất
Industrial Lighting Control (DALI / 0-10 V / LED Driver)
Lighting controllers need 12-bit ADC for light-level sensing, FTM PWM for driver stages, and 5 V tolerance for legacy dimming buses. The MC9S08PA60VLF-FR fits smart fluorescent ballasts, LED drivers, and DALI control modules through its 39 GPIO, dual SCI for DALI/0-10 V communication, and hardware CRC for bus integrity. The 60 KB Flash comfortably stores application code, DALI tables, and an in-application firmware update (IAP) bootloader.
Được đề xuất
Point-of-Load / Multi-Rail Power Control
Industrial 24 V backplanes frequently need an MCU to sequence multiple supply rails, monitor under/over-voltage, and communicate fault status over UART to a host controller. The MC9S08PA60VLF-FR's 12-bit ADC enables precise ADC-based supply monitoring down to 1 mV, while the comparator triggers instantaneous fault shutdown. The 20 MHz HCS08 core executes deterministic power-sequencing state machines with interrupt latency well under 1 µs.
Được đề xuất
Consumer Electronics User Interface (HMI / Keypad / LCD)
Cost-sensitive consumer products—microwave ovens, coffee machines, treadmills, vending machines—need a small 8-bit MCU to drive keypads, segment LCDs or simple TFTs, and run protocol stacks for serial peripherals. The MC9S08PA60VLF-FR's 39 GPIO multiplexes a 4x4 keypad plus 32-segment LCD drive, while 4 KB SRAM holds dual-buffered display data. 256-byte EEPROM saves learned user preferences (volume, brightness, last-program) without external NVM.
Được đề xuất
Battery-Operated Sensor Modules
Although the S08PA targets 5 V operation, its low-power modes (wait, stop3) and fast wake from internal 1 kHz LPO make it viable for periodic sensor reading on a small Li-ion cell or USB supply. The 12-bit ADC handles thermistor, NTC, and 4-20 mA current loop acquisition; the analog comparator offers zero-cross detection and instant wake. For less memory-intensive variants the 32 KB / 16 KB S08PA siblings shrink code storage while keeping the 48-LQFP footprint for PCB reuse.
Được đề xuất
Industrial Sensor Conditioning / 4-20 mA Loop
4-20 mA sensor-transmitter modules require precise ADC ratiometric measurement with excellent PSRR against surge on long cable runs. The MC9S08PA60VLF-FR with its 12-bit ADC and tight reference gives 0.1 %-of-FS accuracy for temperature, pressure, or flow sensor transmitters. EEPROM stores calibration constants, while SCI outputs digital values for HART overlay via external modem. The wide operating temperature range (-40 °C to +105 °C) tolerates outdoor enclosures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC9S08PA60VLF-FR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC9S08PA60VLF | MC9S08PA32VLH | MC9S08PA16VLH | PIC18F46K22-I/P |
|---|---|---|---|---|---|
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 40-DIP (LQFP-48 variant available) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Microchip Technology |
| Core | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | PIC18 (8-bit, 64 MHz) |
| Flash | 60 KB | 60 KB | 32 KB (-47%) | 16 KB (-73%) | 64 KB (+7%) |
| RAM (SRAM) | 4 KB | 4 KB | 4 KB | 1 KB | 3.8 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 1 KB |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.3 V to 5.5 V |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +85 °C |
Bảo phân biệt quan trọng
- 5 V-tolerant bus and ESD/EFT-robust design (vsPIC18F46K22-I/P)
- Memory scaling with identical peripheral IP (vsMC9S08PA60VLF vs MC9S08PA32VLH)
- Wide -40 °C to +105 °C operating range vs narrower alternatives (vsPIC18F46K22-I/P (-40 °C to +85 °C))
- Motor-control FTM with dead-time and fault inputs (vsMC9S08AW60CPUE)
Ghi chú thiết kế
Place a 100 nF X7R decoupling capacitor within 5 mm of every VDD/VSS pair and add a single 4.7 µF bulk capacitor on the main VDD rail. The S08PA's internal voltage regulator supplies the core; do not power core through external rails. For noise-sensitive ADC measurements, route AGND (if exposed) directly to VSS at a single point. When operating from USB or 5 V mains, add a 10 µF bulk on the upstream 5 V rail to absorb switching transients before they reach VDD.
Layout the LQFP-48 footprint with a continuous ground pour on the top layer stitched to VSS pins 6, 20, 48 by short vias. Keep the EXTAL/XTAL traces short and symmetric; place a guard ground around them. Avoid routing high-current motor driver traces (driven by FTM) directly underneath the analog signals—use orthogonal layers with a GND plane between them. For ADC traces, route them over a noise-free reference ground rather than the digital GND pour.
Do not drive any pin above VDD or below VSS—even momentarily—without a current-limiting resistor. The MC9S08PA60VLF-FR is 5 V tolerant on input but not 5 V tolerant on output. Do not skip the BKGD/MS pull-up; without it, the device enters an undocumented mode after reset. The internal 1 kHz LPO is only a backup source—don't use it for UART timing if any baud rate above 4800 is needed.
Estimated: with a 20 MHz bus and 5 V I/O, edge rise/fall of GPIO is roughly 5 ns unloaded. When driving LEDs or relays directly, slow the slew-rate via the appropriate GPIO control register to suppress ringing on long traces. For SCI signals longer than ~30 cm, add 100 Ω series resistors at the driver to damp reflections. Verify SPI timing against the device clock at the maximum bus speed (10 MHz) to ensure data integrity.
Estimated: at full CPU activity and 5 V supply, the MC9S08PA60VLF-FR consumes roughly 25 mA (125 mW). Junction temperature rise using a 48-LQFP θJA of approximately 65 °C/W is about 8 °C above ambient—no heatsink needed for normal use. At extended temperatures near +105 °C, ensure IO drive strength is reduced and unused GPIOs are not configured with high drive, since that contributes additional die power.
Thông tin tuân thủ
RoHS/lead-free per NXP product page; not AEC-Q100 qualified. For automotive sub-systems, request AEC-Q100 S08P variant directly from NXP. -FR suffix is Rochester Electronics authorized aftermarket; the underlying silicon die is unchanged from the master MC9S08PA60VLF NXP part.