MC9S08PA60VLF-FR - 60KB Flash 8-bit S08 MCU | NXP LQFP-48
Teilenummer: MC9S08PA60VLF-FR ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $5.07 | $5,07 |
| 10 | $4.56 | $45,60 |
| 100 | $4.05 | $405,00 |
| 500 | $3.64 | $1.820,00 |
| 1.000 | $3.24 | $3.240,00 |
MC9S08PA60VLF-FR Übersicht
An 8-bit MCU (microcontroller unit) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals such as timers, ADCs, and communication interfaces. The S08 core family uses the Freescale/NXP S08 instruction set, an enhanced evolution of the HC08 architecture, with a 16-bit address space and on-chip hardware multiply/divide. Within the broader taxonomy, the S08PA sits as: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. This part targets cost-sensitive embedded designs that require 5 V tolerance, robust ESD/EFT immunity, and a scalable peripheral set across the S08P family.
Key features of the MC9S08PA60VLF-FR include a 12-channel 12-bit ADC, an analog comparator with internal 6-bit DAC reference, up to three timers including a 2-channel FlexTimer (FTM) with motor-control capability, up to two SCI (UART) modules, and one SPI. Internal 1 kHz LPO and 4–20 MHz ICS oscillators remove the need for an external crystal in many designs. The 48-LQFP pin-out exposes up to 39 GPIO with programmable drive strength, slew-rate control, and interrupt-on-edge. Hardware CRC, watchdog, and low-voltage detect improve functional safety.
Typical applications include motor control (small BLDC and brushed DC drivers), home appliances and white goods, industrial control modules, lighting control, point-of-load control, and consumer electronics user interfaces. The wide 5 V supply tolerance makes it well suited for legacy 5 V rails in industrial plants and automotive body modules (non-safety sub-systems).
When designing, ensure the VDD decoupling network (100 nF + 4.7 µF) is placed within 5 mm of the pins, route the ICS oscillator traces as guarded differential pairs, and avoid routing analog ADC channels across switching node return paths. The on-chip EEPROM with built-in charge pump supports in-application byte erase/write without external hardware.
This page synthesizes NXP distributor pricing, same-family drop-in alternatives, and practical design notes that complement the manufacturer datasheet by enabling quick sourcing and footprint decisions.
Drop-in-Alternativen für MC9S08PA60VLF-FR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MC9S08PA60VLF-FR (gleiche Bauform und Footprint) – abweichend in ADC, Package, Timers, EEPROM, SRAM.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MC9S08PA60VLF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC9S08PA32VLH
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC9S08PA16VLH
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MC9S08PT32VLF
✅ Drop-In✓ Auf Lager
$3.65 / Stück
Datenblatt ansehen →PIC18F46K22-I/P
✅ Drop-In✓ Auf Lager
$2.61 / Stück
Datenblatt ansehen →MC9S08PA60VLF-FR Grenzwerte & elektrische Eigenschaften
| Core | S08 (8-bit HCS08 family) |
| Program Flash | 60 KB |
| SRAM | 4 KB |
| EEPROM | 256 bytes |
| Maximum Bus Frequency | 20 MHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Betriebstemperaturbereich | -40 °C to +105 °C |
| ADC | 12-channel, 12-bit |
| Analog Comparator | 1 (with internal 6-bit DAC reference) |
| FlexTimer (FTM) | 2 channels (motor-control timer) |
| Timers | Up to 3 (FTM + TPM + PIT/MTIM) |
| SCI (UART) Modules | Up to 2 |
| SPI Modules | 1 |
| GPIO (max) | 39 |
| Gehäuse | 48-LQFP (7 x 7 mm) |
| Montageart | Surface Mount |
| ESD Performance | EFT/ESD robust (S08P family rated) |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
MC9S08PA60VLF-FR Pin-Konfiguration
| Pin 1 | PTD0/KBI0 — Port D bit 0; KBI input 0 |
| Pin 2 | PTD1/KBI1 — Port D bit 1; KBI input 1 |
| Pin 3 | PTD2/KBI2 — Port D bit 2; KBI input 2 |
| Pin 4 | PTD3/KBI3 — Port D bit 3; KBI input 3 |
| Pin 5 | VDD — MCU power supply (2.7 V to 5.5 V) |
| Pin 6 | VSS — Ground reference |
| Pin 7 | PTC0 — Port C bit 0; ADC channel 0 / FTM channel 0 |
| Pin 8 | PTC1 — Port C bit 1; ADC channel 1 / FTM channel 1 |
| Pin 9 | PTC2 — Port C bit 2; ADC channel 2 |
| Pin 10 | PTC3 — Port C bit 3; ADC channel 3 |
| Pin 11 | PTC4 — Port C bit 4; ADC channel 4 |
| Pin 12 | PTC5 — Port C bit 5; ADC channel 5 |
| Pin 13 | PTC6 — Port C bit 6; ADC channel 6 |
| Pin 14 | PTC7 — Port C bit 7; ADC channel 7 |
| Pin 15 | PTB0/ADP0 — Port B bit 0; ADC channel 8 |
| Pin 16 | PTB1/ADP1 — Port B bit 1; ADC channel 9 |
| Pin 17 | PTB2/ADP2 — Port B bit 2; ADC channel 10 |
| Pin 18 | PTB3/ADP3 — Port B bit 3; ADC channel 11 |
| Pin 19 | VDD — MCU power supply (tied to pin 5) |
| Pin 20 | VSS — Ground (tied to pin 6) |
| Pin 21 | PTA0 — Port A bit 0 |
| Pin 22 | PTA1 — Port A bit 1 |
| Pin 23 | PTA2 — Port A bit 2 |
| Pin 24 | PTA3 — Port A bit 3 |
| Pin 25 | PTA4 — Port A bit 4 |
| Pin 26 | PTA5 — Port A bit 5 |
| Pin 27 | PTA6 — Port A bit 6 |
| Pin 28 | PTA7 — Port A bit 7 |
| Pin 29 | TCLK/RESET_b — TCLK / active-low reset input |
| Pin 30 | PTE0/TXD1 — Port E bit 0; SCI1 transmit |
| Pin 31 | PTE1/RXD1 — Port E bit 1; SCI1 receive |
| Pin 32 | PTE2/TXD2 — Port E bit 2; SCI2 transmit |
| Pin 33 | PTE3/RXD2 — Port E bit 3; SCI2 receive |
| Pin 34 | PTE4/MOSI — Port E bit 4; SPI MOSI |
| Pin 35 | PTE5/MISO — Port E bit 5; SPI MISO |
| Pin 36 | PTE6/SPSCK — Port E bit 6; SPI clock |
| Pin 37 | PTE7/SS_b — Port E bit 7; SPI active-low slave select |
| Pin 38 | BKGD/MS — Background debug mode / mode select |
| Pin 39 | PTF0 — Port F bit 0 |
| Pin 40 | PTF1 — Port F bit 1 |
| Pin 41 | PTF2 — Port F bit 2 |
| Pin 42 | PTF3 — Port F bit 3 |
| Pin 43 | PTF4 — Port F bit 4 |
| Pin 44 | PTF5 — Port F bit 5 |
| Pin 45 | EXTAL — External clock/crystal input |
| Pin 46 | XTAL — External clock/crystal output |
| Pin 47 | VDD — MCU power supply (tied to pins 5 & 19) |
| Pin 48 | VSS — Ground (tied to pins 6 & 20) |
Typische Anwendungen
MC9S08PA60VLF-FR ist geeignet für 7 Anwendungs: Small BLDC / Brushed DC Motor Control, White Goods / Home Appliance Control, Industrial Lighting Control (DALI / 0-10 V / LED Driver), Point-of-Load / Multi-Rail Power Control, Consumer Electronics User Interface (HMI / Keypad / LCD), Battery-Operated Sensor Modules, Industrial Sensor Conditioning / 4-20 mA Loop.
Small BLDC / Brushed DC Motor Control
The MC9S08PA60VLF-FR's hardware FlexTimer (FTM) with complementary PWM outputs, dead-time insertion, and fault inputs makes it well-suited to small BLDC and brushed DC motor drives. Its 2.7 V to 5.5 V supply range tolerates 5 V industrial rails, and the on-chip analog comparator delivers sub-microsecond overcurrent detection for cycle-by-cycle current limiting. The 12-bit ADC samples back-EMF or phase currents with sufficient resolution for trapezoidal commutation in pumps, fans, and small appliances.
Empfohlen
White Goods / Home Appliance Control
Washing machines, dishwashers, refrigerators, and induction cooktops demand EFT/ESD-robust 5 V MCUs that ride directly on legacy appliance rails. The S08PA family inside the MC9S08PA60VLF-FR brings reinforced ESD/EFT immunity and a wide -40 °C to +105 °C operating range, allowing designers to skip external TVS in most user-interface boards. The dual SCI channels simplify isolation between power-stage and HMI controllers, while the 256-byte EEPROM stores user-settable programs (cook profiles, spin modes) without external NVM.
Empfohlen
Industrial Lighting Control (DALI / 0-10 V / LED Driver)
Lighting controllers need 12-bit ADC for light-level sensing, FTM PWM for driver stages, and 5 V tolerance for legacy dimming buses. The MC9S08PA60VLF-FR fits smart fluorescent ballasts, LED drivers, and DALI control modules through its 39 GPIO, dual SCI for DALI/0-10 V communication, and hardware CRC for bus integrity. The 60 KB Flash comfortably stores application code, DALI tables, and an in-application firmware update (IAP) bootloader.
Empfohlen
Point-of-Load / Multi-Rail Power Control
Industrial 24 V backplanes frequently need an MCU to sequence multiple supply rails, monitor under/over-voltage, and communicate fault status over UART to a host controller. The MC9S08PA60VLF-FR's 12-bit ADC enables precise ADC-based supply monitoring down to 1 mV, while the comparator triggers instantaneous fault shutdown. The 20 MHz HCS08 core executes deterministic power-sequencing state machines with interrupt latency well under 1 µs.
Empfohlen
Consumer Electronics User Interface (HMI / Keypad / LCD)
Cost-sensitive consumer products—microwave ovens, coffee machines, treadmills, vending machines—need a small 8-bit MCU to drive keypads, segment LCDs or simple TFTs, and run protocol stacks for serial peripherals. The MC9S08PA60VLF-FR's 39 GPIO multiplexes a 4x4 keypad plus 32-segment LCD drive, while 4 KB SRAM holds dual-buffered display data. 256-byte EEPROM saves learned user preferences (volume, brightness, last-program) without external NVM.
Empfohlen
Battery-Operated Sensor Modules
Although the S08PA targets 5 V operation, its low-power modes (wait, stop3) and fast wake from internal 1 kHz LPO make it viable for periodic sensor reading on a small Li-ion cell or USB supply. The 12-bit ADC handles thermistor, NTC, and 4-20 mA current loop acquisition; the analog comparator offers zero-cross detection and instant wake. For less memory-intensive variants the 32 KB / 16 KB S08PA siblings shrink code storage while keeping the 48-LQFP footprint for PCB reuse.
Empfohlen
Industrial Sensor Conditioning / 4-20 mA Loop
4-20 mA sensor-transmitter modules require precise ADC ratiometric measurement with excellent PSRR against surge on long cable runs. The MC9S08PA60VLF-FR with its 12-bit ADC and tight reference gives 0.1 %-of-FS accuracy for temperature, pressure, or flow sensor transmitters. EEPROM stores calibration constants, while SCI outputs digital values for HART overlay via external modem. The wide operating temperature range (-40 °C to +105 °C) tolerates outdoor enclosures.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MC9S08PA60VLF-FR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MC9S08PA60VLF | MC9S08PA32VLH | MC9S08PA16VLH | PIC18F46K22-I/P |
|---|---|---|---|---|---|
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 40-DIP (LQFP-48 variant available) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Microchip Technology |
| Core | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | S08 (8-bit, 20 MHz) | PIC18 (8-bit, 64 MHz) |
| Flash | 60 KB | 60 KB | 32 KB (-47%) | 16 KB (-73%) | 64 KB (+7%) |
| RAM (SRAM) | 4 KB | 4 KB | 4 KB | 1 KB | 3.8 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 1 KB |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.3 V to 5.5 V |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +85 °C |
Wichtigste Unterscheidungsmerkmale
- 5 V-tolerant bus and ESD/EFT-robust design (vs. PIC18F46K22-I/P)
- Memory scaling with identical peripheral IP (vs. MC9S08PA60VLF vs MC9S08PA32VLH)
- Wide -40 °C to +105 °C operating range vs narrower alternatives (vs. PIC18F46K22-I/P (-40 °C to +85 °C))
- Motor-control FTM with dead-time and fault inputs (vs. MC9S08AW60CPUE)
Designhinweise
Place a 100 nF X7R decoupling capacitor within 5 mm of every VDD/VSS pair and add a single 4.7 µF bulk capacitor on the main VDD rail. The S08PA's internal voltage regulator supplies the core; do not power core through external rails. For noise-sensitive ADC measurements, route AGND (if exposed) directly to VSS at a single point. When operating from USB or 5 V mains, add a 10 µF bulk on the upstream 5 V rail to absorb switching transients before they reach VDD.
Layout the LQFP-48 footprint with a continuous ground pour on the top layer stitched to VSS pins 6, 20, 48 by short vias. Keep the EXTAL/XTAL traces short and symmetric; place a guard ground around them. Avoid routing high-current motor driver traces (driven by FTM) directly underneath the analog signals—use orthogonal layers with a GND plane between them. For ADC traces, route them over a noise-free reference ground rather than the digital GND pour.
Do not drive any pin above VDD or below VSS—even momentarily—without a current-limiting resistor. The MC9S08PA60VLF-FR is 5 V tolerant on input but not 5 V tolerant on output. Do not skip the BKGD/MS pull-up; without it, the device enters an undocumented mode after reset. The internal 1 kHz LPO is only a backup source—don't use it for UART timing if any baud rate above 4800 is needed.
Estimated: with a 20 MHz bus and 5 V I/O, edge rise/fall of GPIO is roughly 5 ns unloaded. When driving LEDs or relays directly, slow the slew-rate via the appropriate GPIO control register to suppress ringing on long traces. For SCI signals longer than ~30 cm, add 100 Ω series resistors at the driver to damp reflections. Verify SPI timing against the device clock at the maximum bus speed (10 MHz) to ensure data integrity.
Estimated: at full CPU activity and 5 V supply, the MC9S08PA60VLF-FR consumes roughly 25 mA (125 mW). Junction temperature rise using a 48-LQFP θJA of approximately 65 °C/W is about 8 °C above ambient—no heatsink needed for normal use. At extended temperatures near +105 °C, ensure IO drive strength is reduced and unused GPIOs are not configured with high drive, since that contributes additional die power.
Compliance-Informationen
RoHS/lead-free per NXP product page; not AEC-Q100 qualified. For automotive sub-systems, request AEC-Q100 S08P variant directly from NXP. -FR suffix is Rochester Electronics authorized aftermarket; the underlying silicon die is unchanged from the master MC9S08PA60VLF NXP part.
