THÔNG BÁO MUA LẦN CUỐI: MC9S08QB8CWL sắp tới cuối cuộc sống. Ngày đặt hàng cuối cùng: Liên hệ với chúng tôi. Xem các bộ phận thay thế có sẵn →
NXP Semiconductors

MC9S08QB8CWL - 8-Bit 20MHz USB MCU, 8KB Flash | NXP

MPN: MC9S08QB8CWL ✗ Cuối đời
2.5 V or 3.3 V Vdss 28-pin SOIC Package 20 MHz Speed 8 KB (8K x 8) Memory
MOQ: 1 |

MC9S08QB8CWL Tóm tắt

The NXP Semiconductors MC9S08QB8CWL is an 8-bit S08 microcontroller with a 20 MHz maximum operating frequency, 8 KB of Flash memory, and an integrated USB device controller. The device is packaged in a 28-pin SOIC and operates from a 2.5 V or 3.3 V supply, making it suitable for compact USB-connected control, data-acquisition, and low-cost embedded systems.

A microcontroller is the central programmable component of an embedded system, combining a CPU core, memory, timers, serial interfaces, and digital I/O on one integrated circuit. The S08 family uses an 8-bit CISC architecture intended for straightforward control logic. Compared with larger 32-bit Cortex-M devices, the MC9S08QB8CWL concentrates basic USB connectivity, timing resources, and general-purpose I/O in a modest 28-pin package while consuming substantially less program memory.

Key device characteristics include 8 KB of Flash for firmware storage, 512 bytes of RAM, a 20 MHz clock capability, 24 I/O lines, and up to 20 GPIO functions according to the NXP product information. The integrated USB device controller reduces the need for a separate USB interface IC, although firmware, transceiver integration, and power-supply requirements still need to be checked against the complete datasheet before a USB design is released.

The S08 architecture also provides multiple timers for periodic measurement, motor control, timing events, or debouncing. Its 2.5 V and 3.3 V operating options fit legacy industrial peripherals, USB-connected test equipment, compact control panels, and accessory controllers where board area and power consumption are more important than high-performance arithmetic. The 28-pin SOIC package is also easier to hand-assemble and inspect than fine-pitch land-grid-array devices.

When laying out a new board, treat USB signal integrity as a dedicated design task. Route D+ and D+ as a short, continuous, impedance-controlled pair, place the required series termination close to the controller, and follow the manufacturer reference layout for decoupling and grounding. Confirm the exact USB clock and transceiver requirements in the MC9S08QB8 datasheet before finalizing the schematic and PCB stack-up.

NXP lists the MC9S08QB8CWL as End of Life. New production designs should therefore account for future sourcing risk and consider an actively supported MCU with a defined migration path. For an existing design, preserve the SOIC footprint, verify every peripheral, port, interrupt vector, and voltage requirement, and validate replacement firmware before production quantities are released.

This page combines lifecycle status, memory and interface specifications, drop-in migration options, package details, and practical replacement guidance into one engineering-focused reference for maintaining or redesigning MC9S08QB8CWL-based equipment.

Bộ thay thế dễ dàng lắp đặt cho MC9S08QB8CWL — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S08QB8CWL (cùng hình factor và footprint) — khác nhau ở Core Architecture, Package, RAM, Maximum CPU Frequency, RoHS Status.

NXP Semiconductors
Core Architecture: HCS08 (8-bit CISC, HC08-compatible)
Package: 16-pin TSSOP (Tape and Reel)
RAM: 256 bytes
So sánh với MC9S08QB8CWL →
NXP Semiconductors
Core Architecture: CISC, Harvard, 3-stage pipeline
Package: 28-pin SOIC W (7 mm x 7 mm, 1.40 mm height, 0.80 mm pitch)
RAM: 512 B
So sánh với MC9S08QB8CWL →

MC9S08QG8CWL

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 28-pin SOIC
Same S08 family, 28-pin SOIC footprint and 8 KB Flash class; approximately 10% lower assumed feature proximity because peripheral and USB details must be verified

📋 Tham chiếu thay thế (không có trong danh mục)

MC9S08QH8CWL

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 28-pin SOIC
Same S08 family and 28-pin SOIC footprint; approximately 20% lower assumed feature proximity because memory, timer, and USB feature differences require datasheet verification

📋 Tham chiếu thay thế (không có trong danh mục)

MC9S08QE8CWL

✅ Drop-In ⚠️ Thông số chưa được xác minh
NXP Semiconductors
📦 28-pin SOIC
HCS08 (S08) · 8-bit · CISC, Harvard, 3-stage pipeline · 20 MHz at 1.8 V; 50.33 MHz bus at 2.1 V · 8 KB (8K x 8) · 512 B · 1.8 V to 3.6 V · 28

Liên hệ để biết giá

Xem tài liệu →

MC9S08QF8CWL

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 28-pin SOIC
Same S08 family and 28-pin SOIC land pattern; approximately 20% lower assumed feature proximity because timer mapping and USB behavior are not established

📋 Tham chiếu thay thế (không có trong danh mục)

MC9S08QL8CWL

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 28-pin SOIC
Same S08 family, 28-pin SOIC footprint and comparable 8-bit controller position; approximately 30% lower assumed feature proximity pending complete peripheral verification

📋 Tham chiếu thay thế (không có trong danh mục)

MC9S08QB8CWL Tỷ lệ tối đa & tính chất điện

Manufacturer NXP Semiconductors
Product Type 8-bit microcontroller with integrated USB device controller
Core Architecture S08, 8-bit CISC
Tần số xung maksimum 20 MHz
Flash Memory 8 KB (8K x 8)
RAM 512 bytes
Supply Voltage Options 2.5 V or 3.3 V
Hộp 28-pin SOIC
Kiểu lắp đặt Surface mount
USB Interface Integrated USB device controller
I/O Lines 24
General-Purpose I/O Up to 20 GPIO
Timer Resources Multiple timers
Microcontroller Width 8-bit
Trạng thái vòng đời End of Life

Hướng dẫn cấu hình chân MC9S08QB8CWL 28-pin soic

Cấu hình chân cho MC9S08QB8CWL (28-pin soic gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 28-pin soic cho MC9S08QB8CWL

Không có dữ liệu chân cụ thể sẵn có cho MC9S08QB8CWL.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MC9S08QB8CWL phù hợp cho 6 Áp dụngs: USB Peripheral Controller, Industrial Data-Acquisition Module, Control Panel and HMI Backplane, USB Connected Test Accessory, Low-Cost Sensor Gateway, Appliance and Accessory Controller.

🖥️

USB Peripheral Controller

The MC9S08QB8CWL fits compact USB peripheral designs because it combines an 8-bit S08 core with an integrated USB device controller in a 28-pin SOIC package. Its 8 KB of Flash is suitable for enumeration code, command handling, status reporting, and configuration storage, while 512 bytes of RAM supports short protocol buffers and control state. A practical design uses the device as the USB target while a timer or serial interface handles local control functions. The 20 MHz maximum clock provides margin for protocol servicing, but actual USB throughput depends on the endpoint configuration and firmware. Keep the USB data routing compact and validate the required pull-up, termination, clock, and decoupling arrangements against the manufacturer reference design before release.

🏭

Industrial Data-Acquisition Module

For a compact acquisition module, the MC9S08QB8CWL can coordinate sensors, digital status inputs, and a host connection while its 24 I/O lines handle discrete monitoring functions. The 8-bit S08 core is appropriate for scaling or formatting moderate volumes of sensor data rather than intensive signal analysis. Multiple timers can establish acquisition intervals, sample timing, watchdog activity, and communication timeouts. Operate the device from 2.5 V or 3.3 V according to the selected peripheral interface levels, and use the 20 MHz clock only when the timing budget requires it. Because the device is End of Life, production equipment should isolate any new expansion behind a documented interface or plan a controller upgrade that preserves the existing external connector and field-bus behavior.

📺

Control Panel and HMI Backplane

The MC9S08QB8CWL can serve as the low-power controller behind a simple control panel, keypad reader, status display, or relay-control board. Its 20 GPIO-capable functions, multiple timers, and 8-bit processing core are adequate for button scanning, indicator control, debouncing, and sequencing. The 512 bytes of RAM favors event-driven firmware that does not retain large display frames or history buffers. Use timers for debounce intervals and periodic display updates instead of blocking delays, which improves responsiveness and lowers overall energy use. The 28-pin SOIC footprint remains practical for hand assembly and repair, but a complete replacement assessment must verify LCD or LED driver requirements, port multiplexing, and any communications peripherals beyond the integrated USB device controller.

🧪

USB Connected Test Accessory

A programmable test accessory is a natural application for the MC9S08QB8CWL because USB connectivity, multiple timers, and a general-purpose I/O complement are combined in one controller. The firmware can implement a simple command interpreter, collect switch or sensor states, generate timing signals, and report results to a host computer. The 8 KB Flash limit favors compact command tables and configuration structures rather than storing large test vectors. Keep timing-critical functions on dedicated timers and avoid heavy processing inside USB interrupt service routines. The 20 MHz clock capability allows efficient event handling at this memory level. Before cloning the accessory, reproduce the original USB enumeration sequence, verify pull-up states during reset, and confirm that the replacement candidate preserves every port assignment used by external test points.

🧩

Low-Cost Sensor Gateway

The MC9S08QB8CWL can act as a small sensor gateway when the design needs local digital I/O, periodic sampling, and a host-facing USB link rather than high-bandwidth analog processing. Use its multiple timers for sampling intervals and communication timing, and use the 24 I/O lines for discrete sensors, interrupt inputs, and status outputs. The 8-bit architecture keeps firmware and memory requirements modest for compact energy-budgeted products. Since the part is End of Life, new gateway designs should evaluate the availability of the MCU, USB transceiver requirements, and field-upgrade strategy together. A migration to another S08 device is easiest when the PCB is unchanged, but the USB descriptors, timing behavior, and peripheral assignments must be validated under worst-case load conditions.

⚡

Appliance and Accessory Controller

Home appliances, printers, laboratory accessories, and communication equipment often need a compact controller that manages a few outputs, senses switch states, and exposes service data to a host. The MC9S08QB8CWL supplies the core processing, 8 KB of program storage, 512 bytes of RAM, multiple timers, and an integrated USB device controller for that role. Its 2.5 V or 3.3 V operation supports both legacy and modern peripheral voltage levels, while the 28-pin SOIC simplifies rework. Design the firmware around interrupt-driven events and timer-based scheduling rather than intensive polling. When sustaining an existing appliance, check the original power-cycling behavior, boot timing, USB descriptors, and brownout margins; these characteristics can differ between same-family candidates even when the land pattern remains unchanged.

Tóm tắt các sản phẩm được đề xuất

MC9S08QB8CWL NXP Semiconductors Được sử dụng trong: USB Peripheral Controller, Industrial Data-Acquisition Module, Control Panel and HMI Backplane, USB Connected Test Accessory, Low-Cost Sensor Gateway, Appliance and Accessory Controller MC9S08QG8CWL Same-family S08 migration candidate Được sử dụng trong: USB Peripheral Controller, Appliance and Accessory Controller MC9S08QE8CWL NXP Semiconductors Được sử dụng trong: Industrial Data-Acquisition Module MC9S08QF8CWL Same-family S08 migration candidate Được sử dụng trong: Control Panel and HMI Backplane MC9S08QH8CWL Same-family S08 migration candidate Được sử dụng trong: USB Connected Test Accessory MC9S08QL8CWL Same-family S08 migration candidate Được sử dụng trong: Low-Cost Sensor Gateway
What is the MC9S08QB8CWL?
The MC9S08QB8CWL is an NXP Semiconductors 8-bit S08 microcontroller with a 20 MHz maximum clock, 8 KB of Flash memory, and an integrated USB device controller. According to the NXP product information, the device also includes 512 bytes of RAM, multiple timers, and up to 20 GPIO functions in a 28-pin SOIC package. It is intended for compact embedded control and USB-connected peripheral designs.
Is the MC9S08QB8CWL still in production?
No. NXP lists the MC9S08QB8CWL as End of Life on its official product page. The device may still be available through legacy inventory channels, but a new design should not assume ongoing production. Request the current availability and lifecycle position through the Request a Quote form on this page, and plan a board-level migration if the product must remain in production for many years.
What is the memory configuration of the MC9S08QB8CWL?
The MC9S08QB8CWL provides 8 KB of Flash memory organized as 8K x 8 and includes 512 bytes of RAM. The NXP product listing and distributor specifications identify the Flash as the primary on-chip program-memory resource. This configuration suits compact control firmware, USB device-state handling, peripheral polling, and simple communication protocols, but it is not appropriate for large graphical interfaces or complex application frameworks.
What is the maximum operating frequency of the MC9S08QB8CWL?
The maximum operating frequency is 20 MHz. NXP distributor and manufacturer listings identify the MC9S08QB8CWL as an 8-bit S08 MCU rated for 20 MHz operation. Actual bus timing, flash wait states, peripheral clock behavior, and voltage-dependent operating limits should be taken from the manufacturer datasheet, especially when the design relies on precise timing or continuous USB traffic.
Which package does the MC9S08QB8CWL use?
The MC9S08QB8CWL uses a 28-pin SOIC package. NXP and distributor listings both identify the device as a 28-SOIC part, making it suitable for surface-mount assembly and for boards that avoid very fine-pitch packages. The suffix CWL denotes the specific ordering configuration, so the land pattern must be checked against the 28-pin SOIC footprint rather than a 24-pin or leaded-package drawing.
Can the MC9S08QB8CWL be used for USB device applications?
Yes, the MC9S08QB8CWL includes an integrated USB device controller. This allows a compact product to implement USB peripheral behavior without adding a separate USB interface controller. Firmware must still handle enumeration, descriptors, endpoint scheduling, and the required clock configuration. For a production board, follow the manufacturer USB reference layout and verify whether an external USB transceiver is required for the intended operating mode.
What can replace the MC9S08QB8CWL in an existing PCB?
The closest replacements are the same-family MC9S08QB8 devices offered in comparable 28-pin SOIC configurations, subject to memory, clock, USB, and peripheral matching. The alternatives listed for this page are migration candidates, not automatic approvals. Use the Request a Quote form on this page to request availability information, then compare the candidate datasheet pin-by-pin and validate the existing firmware before substituting any part.
When should I choose the MC9S08QB8CWL over a newer MCU?
Choose the MC9S08QB8CWL only when preserving an existing 28-pin SOIC board and its proven firmware has more value than long-term lifecycle security. Its 8-bit S08 core, 8 KB Flash, 20 MHz clock, and integrated USB device controller are sufficient for modest control tasks. For a new product with long service life, additional memory, greater peripheral bandwidth, or a broader software roadmap, an actively supported MCU is normally the better choice.
MC9S08QB8CWL vs MC9S08QG8CWL: which one should I use?
The MC9S08QB8CWL and MC9S08QG8CWL belong to the same NXP S08QB-related migration group, but the correct choice depends on the detailed peripheral map, memory capacity, USB implementation, and package-specific pin assignments. The two are not interchangeable merely because both use a 28-pin SOIC. Compare the manufacturer datasheets for every port, power pin, interrupt source, clock connection, and USB signal before approving either device.
What is the best NXP equivalent for the MC9S08QB8CWL?
The best NXP equivalent is the same-family part whose complete pin and peripheral configuration matches the existing design, not simply the nearest flash-memory size. Candidates in the MC9S08QB8 and closely related S08 families can preserve the SOIC footprint, but USB behavior, timer channels, port multiplexing, and pin electrical limits must match. Request lifecycle and sourcing information through the Request a Quote form on this page.
Where can I download the MC9S08QB8CWL datasheet?
The official MC9S08QB8CWL datasheet and product documentation are available through the NXP part page at https://www.nxp.com/part/MC9S08QB8CWL. Use the manufacturer datasheet for the authoritative pin list, electrical characteristics, USB clock requirements, memory map, and recommended application circuit. The product page also carries the lifecycle, shipping, and end-of-life notices needed when planning a replacement.
Where can I find the MC9S08QB8CWL pinout?
The authoritative MC9S08QB8CWL pinout is found in the pin-description table of the NXP MC9S08QB8 manufacturer datasheet. The device is a 28-pin SOIC, but the page does not reproduce individual pin names because a package drawing alone does not establish the electrical function of every lead. Use the datasheet pin table when assigning PCB nets, especially for power, ground, clock, reset, and USB connections.
How do I design the USB layout for an MC9S08QB8CWL board?
Route the USB data pair as a short, continuous pair on the same PCB layer, with no plane changes or stubs beneath it. Apply the manufacturer reference layout for series termination, crystal or clock components, decoupling, and ground return paths. Keep switching regulators and high-current digital edges away from the data traces, and verify the completed layout against the USB impedance and return-path requirements in the datasheet.
How much power does an MC9S08QB8CWL design require?
Total board power depends on the selected 2.5 V or 3.3 V supply, MCU operating mode, USB activity, timer activity, and the loads driven by the 24 I/O lines. The listed 20 MHz clock rate is a maximum capability rather than a continuous-power rating. Use the datasheet operating-current and active-current graphs for a defensible power budget, then include regulator loss, USB pull-up loading, and peripheral loads in the supply sizing.
What are the key specifications of MC9S08QB8CWL that engineers should know?
The MC9S08QB8CWL combines an 8-bit S08 core, a 20 MHz maximum clock, 8 KB of Flash, 512 bytes of RAM, 2.5 V or 3.3 V operation, multiple timers, and an integrated USB device controller. The NXP product information also identifies up to 20 GPIO functions and the device is offered in a 28-pin SOIC. It is an End-of-Life part, so its legacy suitability is balanced against long-term sourcing risk.

Dữ liệu tham khảo kỹ thuật cho MC9S08QB8CWL — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Select the MC9S08QB8CWL when an existing 28-pin SOIC design must be maintained with minimal hardware changes and its 8 KB Flash, 512-byte RAM, 20 MHz clock, and integrated USB device controller satisfy the product requirements. Its End-of-Life status makes it primarily appropriate for repair, spare-part, and previously validated production programs. When selecting a migration candidate, treat the footprint match as the minimum requirement and verify memory, USB, timers, port multiplexing, clock, reset, and firmware compatibility. MC9S08QG8CWL is the closest listed candidate because it belongs to the same NXP S08 family, but all five alternatives require datasheet-level review. For a completely new product with long-term sourcing needs, select an actively supported controller with adequate memory and a clear software roadmap instead of inheriting this legacy platform.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này MC9S08QG8CWL MC9S08QH8CWL MC9S08QE8CWL MC9S08QF8CWL MC9S08QL8CWL
Manufacturer NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 28-pin SOIC 28-pin SOIC - same footprint class 28-pin SOIC - same footprint class 28-pin SOIC - same footprint class 28-pin SOIC - same footprint class 28-pin SOIC - same footprint class
Core Architecture 8-bit S08 CISC 8-bit S08 CISC 8-bit S08 CISC 8-bit S08 CISC 8-bit S08 CISC 8-bit S08 CISC

Bảo phân biệt quan trọng

  • Integrated USB device controller in a compact 8-bit MCU (vsMC9S08QE8CWL)
  • Higher documented clock capability than the assumed migration band (vsMC9S08QH8CWL)
  • Documented 8 KB Flash configuration (vsMC9S08QF8CWL)

Ghi chú thiết kế

Follow the manufacturer reference layout for the USB data pair, series termination, clock components, and decoupling. Route D+ and D- together without stubs or plane transitions, and provide a continuous return path beneath the pair. Because the device also supports legacy 2.5 V and 3.3 V system levels, keep USB and processor-side return currents tightly coupled and separate noisy switching-current paths from the interface area.

Size the supply from the worst-case operating state rather than the nominal 20 MHz clock rate. Include the MCU's active current, timer activity, USB load, external pull-up current, and every I/O load connected to the 3.3 V or 2.5 V rail. Use the datasheet current-versus-frequency and operating-mode graphs, and check regulator headroom at the highest specified temperature to avoid brownout resets during USB enumeration.

Do not approve a migration from the footprint alone. Compare power pins, ground connections, clock pins, reset behavior, USB data pins, port multiplexing, interrupt vectors, and timer channels between the original and candidate datasheets. Preserve the original firmware tool and boot configuration, then test reset, enumeration, brownout recovery, and every external I/O under worst-case loading before releasing replacement quantities.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

NXP identifies the MC9S08QB8CWL as End of Life. Detailed RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification statements were not established from the available manufacturer and distributor information.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MC9S08QB8CWL datasheet MC9S08QB8CWL pinout MC9S08QB8CWL datasheet pdf MC9S08QB8CWL equivalent MC9S08QB8CWL replacement MC9S08QB8CWL cross reference MC9S08QB8CWL price MC9S08QB8CWL stock MC9S08QB8CWL vs MC9S08QG8CWL NXP MC9S08QB8CWL MC9S08QB8CWL 28 SOIC footprint MC9S08QB8CWL USB schematic MC9S08QB8CWL application circuit where to buy MC9S08QB8CWL MC9S08QB8CWL lead time

Các bộ phận và thuật ngữ liên quan

NXP Semiconductors MC9S08QB8CWL MC9S08QB8 MC9S08QG8CWL MC9S08QH8CWL MC9S08QE8CWL MC9S08QF8CWL MC9S08QL8CWL S08 core 8-bit CISC microcontroller microcontroller embedded system USB device controller 28-pin SOIC SOIC package family surface-mount package 8 KB Flash memory 512-byte RAM 20 MHz clock GPIO timer End of Life RoHS REACH
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ