MCF51JM64VQH - ColdFire V1 32-bit MCU, 64KB Flash, 50MHz | NXP
MPN: MCF51JM64VQH ✓ Hoạt độngMCF51JM64VQH Tóm tắt
A microcontroller (MCU) is a single-chip computer integrating a CPU core, program and data memory, peripherals, and I/O. ColdFire V1 is a 32-bit reduced instruction set computing (RISC) architecture derived from the original ColdFire family, optimized for embedded deterministic control with small code size and low power. Within the broader semiconductor taxonomy, the MCF51JM64 belongs to the microcontrollers hierarchy (microcontroller -> 32-bit MCU -> embedded processor -> semiconductor IC). The Flexis positioning is significant: a designer can prototype on a JM device and migrate to an S08 pin-compatible MCU without a full PCB redesign.
Key specifications include a 32-bit ColdFire V1 core at 50 MHz, 64 KB flash program memory, 8 KB SRAM, an 8-channel 12-bit ADC, timers (including PWM channels), SPI, I²C, and UART communication peripherals, plus a USB 2.0 Full-Speed (12 Mbps) device/host/on-the-go controller. The 64-pin LQFP package supports industrial-grade -40°C to +105°C operation. The integrated USB controller with on-chip transceiver eliminates external PHY requirements for many USB device applications.
Architecturally, the MCF51JM64 uses a Harvard-oriented ColdFire V1 core with a single-cycle 32-bit ALU, hardware multiply/accumulate, and a tightly-coupled peripheral bus. The Flexis shared-peripheral philosophy with the S08 family means the same peripheral IP blocks (ADC, timers, communications modules) appear on both families, allowing identical firmware drivers across 8-bit and 32-bit performance tiers.
Typical applications include industrial control and sensor conditioning, building automation and HVAC controllers, USB peripherals such as HID-class human-interface devices, low-end medical instruments, consumer electronics requiring a USB device interface, and small-form-factor embedded control boards. The integrated USB 2.0 FS OTG controller also makes the part suitable for point-of-sale terminals and cable replacement use cases.
Designers should note that the MCF51JM family is being maintained primarily for legacy and industrial embedded designs, and lifecycle support should be confirmed against the latest NXP product change notifications. When planning new designs, evaluate the MCF51JM128 (128 KB flash) or Kinetis E series as longer-term alternatives while keeping the JM family in scope for proven, qualified, and stable code reuse.
This page synthesizes distributor pricing, parametric comparison, and Flexis migration notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho MCF51JM64VQH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCF51JM64VQH (cùng hình factor và footprint) — khác nhau ở Package, Program Memory Size, Architecture, Connectivity, Series.
MCF51JM128VQH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKE02Z64VQH4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MKE02Z64VLD2
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MKE04Z64VLK4R
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MKL26Z32VLH4
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MCF51JM64VQH Tỷ lệ tối đa & tính chất điện
| Manufacturer | NXP Semiconductors |
| Core | ColdFire V1 (32-bit RISC) |
| Processor Series | MCF51JM (Flexis) |
| Maximum CPU Frequency | 50 MHz |
| Program Memory Size | 64 KB (64K x 8) FLASH |
| RAM Size | 8 KB |
| Bề rộng đường dữ liệu | 32 bit |
| Hộp | 64-LQFP (14x14 mm) |
| Số chân | 64 |
| Kiểu lắp đặt | Surface Mount |
| USB Controller | USB 2.0 Full-Speed Device/Host/OTG with on-chip transceiver |
| ADC | 8-channel, 12-bit SAR |
| Communication Peripherals | SPI, I2C, USB FS OTG |
| Family | Flexis (pin-compatible with S08 family) |
Cấu hình chân MCF51JM64VQH
| Chân 1 | PTE0/TxD1 — Port E bit 0 / UART1 transmit |
| Chân 2 | PTE1/RxD1 — Port E bit 1 / UART1 receive |
| Chân 3 | PTE2 — Port E bit 2 |
| Chân 4 | PTE3 — Port E bit 3 |
| Chân 5 | PTE4 — Port E bit 4 |
| Chân 6 | PTE5 — Port E bit 5 |
| Chân 7 | PTE6 — Port E bit 6 |
| Chân 8 | PTE7 — Port E bit 7 |
| Chân 9 | VSS — Ground |
| Chân 10 | PTF0 — Port F bit 0 |
| Chân 11 | PTF1 — Port F bit 1 |
| Chân 12 | PTF2 — Port F bit 2 |
| Chân 13 | PTF3 — Port F bit 3 |
| Chân 14 | PTF4 — Port F bit 4 |
| Chân 15 | PTF5 — Port F bit 5 |
| Chân 16 | PTF6 — Port F bit 6 |
| Chân 17 | PTF7 — Port F bit 7 |
| Chân 18 | VDD — Digital supply voltage |
| Chân 19 | USB_DP — USB D+ data line |
| Chân 20 | USB_DM — USB D- data line |
| Chân 21 | VREGIN — USB regulator input |
| Chân 22 | VOUT33 — USB 3.3V regulator output |
| Chân 23 | PTG0 — Port G bit 0 |
| Chân 24 | PTG1 — Port G bit 1 |
| Chân 25 | PTG2 — Port G bit 2 |
| Chân 26 | PTG3 — Port G bit 3 |
| Chân 27 | PTA0 — Port A bit 0 |
| Chân 28 | PTA1 — Port A bit 1 |
| Chân 29 | PTA2 — Port A bit 2 |
| Chân 30 | PTA3 — Port A bit 3 |
| Chân 31 | PTA4 — Port A bit 4 |
| Chân 32 | PTA5 — Port A bit 5 |
| Chân 33 | PTA6 — Port A bit 6 |
| Chân 34 | PTA7 — Port A bit 7 |
| Chân 35 | PTB0 — Port B bit 0 |
| Chân 36 | PTB1 — Port B bit 1 |
| Chân 37 | PTB2 — Port B bit 2 |
| Chân 38 | PTB3 — Port B bit 3 |
| Chân 39 | PTB4 — Port B bit 4 |
| Chân 40 | PTB5 — Port B bit 5 |
| Chân 41 | PTB6 — Port B bit 6 |
| Chân 42 | PTB7 — Port B bit 7 |
| Chân 43 | PTC0 — Port C bit 0 |
| Chân 44 | PTC1 — Port C bit 1 |
| Chân 45 | PTC2 — Port C bit 2 |
| Chân 46 | PTC3 — Port C bit 3 |
| Chân 47 | PTC4 — Port C bit 4 |
| Chân 48 | PTC5 — Port C bit 5 |
| Chân 49 | PTC6 — Port C bit 6 |
| Chân 50 | PTC7 — Port C bit 7 |
| Chân 51 | PTD0 — Port D bit 0 |
| Chân 52 | PTD1 — Port D bit 1 |
| Chân 53 | PTD2 — Port D bit 2 |
| Chân 54 | PTD3 — Port D bit 3 |
| Chân 55 | PTD4 — Port D bit 4 |
| Chân 56 | PTD5 — Port D bit 5 |
| Chân 57 | PTD6 — Port D bit 6 |
| Chân 58 | PTD7 — Port D bit 7 |
| Chân 59 | RESET — Active-low reset input |
| Chân 60 | EXTAL — External crystal/oscillator input |
| Chân 61 | XTAL — External crystal output |
| Chân 62 | TEST — Test mode (tie to ground in normal use) |
| Chân 63 | BKGD — Background debug mode |
| Chân 64 | VDDA/VREFH — Analog supply / ADC reference high |
Ứng dụng tiêu biểu
MCF51JM64VQH phù hợp cho 6 Áp dụngs: USB HID / Human-Interface Device, Industrial Sensor Conditioning, Building Automation / HVAC, USB-to-Serial Bridge / Point-of-Sale Terminal, Low-End Medical Instruments, Consumer USB Device / Embedded Control.
USB HID / Human-Interface Device
The MCF51JM64VQH's integrated USB 2.0 Full-Speed Device/Host/OTG controller with on-chip transceiver suits HID and CDC-class peripherals where BOM minimalism is critical. The 50 MHz ColdFire V1 core runs typical 8-16 KB USB HID/CDC stacks with 32-48 KB headroom for application logic in 64 KB flash. Unlike external-USB USB MCU solutions, the JM64 eliminates external PHY parts. Pin-compatible migration to the Kinetis E family (MKE02Z64VQH4) lets designers swap cores while reusing PCBs and drivers.
Được đề xuất
Industrial Sensor Conditioning
The 8-channel 12-bit SAR ADC and 50 MHz ColdFire V1 core make the MCF51JM64VQH suitable for multi-channel sensor-conditioning applications such as process transmitters, multi-zone HVAC controllers, and factory-floor analog front-end nodes. With 50 MHz performance, the JM64 can sample 8 channels at 10 kHz with on-chip averaging and still meet deterministic control loops. The 64-LQFP industrial package supports harsh-environment deployment with proper PCB layout. Flexis compatibility lets engineers migrate to the S08 family for lower-cost pin-compatible daughterboards.
Được đề xuất
Building Automation / HVAC
The MCF51JM64VQH fits building-automation gateways and HVAC zone controllers where 8 KB SRAM holds modest control tables and the ColdFire V1 core executes 50 MHz control loops. The integrated USB 2.0 FS controller supports commissioning ports, and the 12-bit ADC reads thermistor and 0-10 V sensor inputs. Unlike smaller 8-bit S08 alternatives, the JM64 gives 32-bit headroom for future firmware features while remaining pin-compatible. PCB layout benefits from industrial-grade 64-LQFP thermal handling.
Được đề xuất
USB-to-Serial Bridge / Point-of-Sale Terminal
The MCF51JM64VQH's USB 2.0 FS OTG controller with on-chip transceiver enables cable-replacement and POS terminal applications without external PHY. The 50 MHz ColdFire V1 core runs USB CDC stacks plus protocol translation, and the 64 KB flash holds descriptors and application code. Unlike USB-capable 8-bit MCUs, the JM64's 32-bit ALU accelerates descriptor parsing and bulk-packet reformatting. Designers benefit from a single-chip USB bridge solution.
Được đề xuất
Low-End Medical Instruments
The MCF51JM64VQH suits low-end patient-monitoring peripherals, electronic stethoscopes, and USB-connected diagnostic accessories where 64 KB flash and 50 MHz ColdFire V1 performance are sufficient. The 12-bit ADC reads analog sensor channels at medical-grade resolution, and the 64-LQFP industrial package supports medical-device PCB layouts. Flexis shared-peripheral compatibility lets designers move to S08 family pin-compatible daughterboards for cost-sensitive variants.
Được đề xuất
Consumer USB Device / Embedded Control
The MCF51JM64VQH targets compact consumer USB devices and small embedded control boards where a single-chip MCU with integrated USB simplifies BOM. The 50 MHz ColdFire V1 core plus 8 KB SRAM executes typical consumer device firmware, and the 12-bit ADC adds analog monitoring. Unlike external-USB consumer MCU solutions, the JM64 integrates PHY. NXP's Flexis compatibility ensures proven firmware portability to S08 family pin-compatible variants for cost reduction.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCF51JM64VQH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCF51JM128VQH | MKE02Z64VQH4 | MKE02Z64VLD2 | MKE04Z64VLK4R | MKL26Z32VLH4 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (14x14 mm) | 64-LQFP (14x14 mm) - same | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same |
| Core Architecture | ColdFire V1 (32-bit RISC) | ColdFire V1 (32-bit RISC) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ (32-bit) |
| Flash Memory | 64 KB | 128 KB | 64 KB | 64 KB | 64 KB | 32 KB |
| USB Controller | USB 2.0 FS Device/Host/OTG with PHY | USB 2.0 FS Device/Host/OTG with PHY | No USB | No USB | No USB | USB 2.0 FS Device/Host/OTG with PHY |
| Family / Line | Flexis (ColdFire V1 JM) | Flexis (ColdFire V1 JM) | Kinetis E (ARM M0+) | Kinetis E (ARM M0+) | Kinetis E (ARM M0+) | Kinetis L (ARM M0+) |
| Toolchain / IDE | CodeWarrior (ColdFire) | CodeWarrior (ColdFire) | Kinetis SDK / Keil / IAR / MCUXpresso | Kinetis SDK / Keil / IAR / MCUXpresso | Kinetis SDK / Keil / IAR / MCUXpresso | Kinetis SDK / Keil / IAR / MCUXpresso |
Bảo phân biệt quan trọng
- Higher flash density in same 64-LQFP package (vsMCF51JM128VQH)
- Integrated USB 2.0 FS OTG with on-chip PHY (vsMKE02Z64VQH4)
- ColdFire V1 RISC architecture (vsMKE02Z64VQH4)
Ghi chú thiết kế
Estimated: the MCF51JM64VQH draws core current on the order of tens of milliamps at 50 MHz in active run mode. Decouple VDD and VDDA/VREFH with a 100 nF ceramic capacitor placed within 5 mm of each supply pin, plus a 4.7 µF bulk capacitor on VDD. Route VDDA separately from VDD to reduce ADC noise coupling; add a ferrite bead if shared. The on-chip USB 3.3 V regulator requires a 4.7 µF decoupling capacitor on VOUT33.
Place the external crystal or oscillator within 5 mm of the EXTAL/XTAL pins and route symmetrical traces with a ground guard ring to minimize EMI coupling. Keep USB_DP/USB_DM traces as a 90-ohm differential pair with controlled impedance, matching lengths within 150 mils (3.8 mm), and route away from switching nodes. Use a 4-layer PCB stackup with continuous ground plane beneath the LQFP-64 for thermal spreading.
Estimated: leave the TEST pin tied to VSS via 10 kΩ for normal operation; floating it may invoke BDM/test modes. The BKGD pin requires proper pull-down or pull-up per the ColdFire debug interface specification; not configuring it correctly can lock out background debug. Verify the RESET pin decoupling (typical 1 nF + 10 kΩ pull-up) so the BGKP debug interface is not asserted unintentionally. Confirm voltage levels on VDDA/VREFH before enabling ADC conversions.
Thông tin tuân thủ
Compliance fields not explicitly stated in verified snippets; engineer should consult NXP product page environmental compliance section for RoHS, REACH, lead-free, and halogen-free status. Part is industrial-grade, not AEC-Q100 qualified.
