MCP3550-50E/MS - 22-Bit 12.5 SPS ADC | Microchip
MPN: MCP3550-50E/MS ✓ Hoạt độngMCP3550-50E/MS Tóm tắt
A delta-sigma ADC is a voltage-to-digital converter that uses oversampling, noise shaping, and digital filtering to obtain high resolution from relatively slow, low-frequency measurements. Within the converter hierarchy, the MCP3550-50E/MS belongs to the sigma-delta ADC family and is optimized for sensor signals where low noise and compact analog circuitry are more important than high conversion speed.
The 22-bit resolution provides substantially more code density than conventional lower-resolution SAR ADCs. Its single-channel architecture simplifies analog routing, while the fully differential input structure supports direct connection to bridge sensors and other balanced sources. The manufacturer identifies the device as a low-power, single-channel converter intended for pressure, temperature, humidity, and similar sensor measurements.
The MCP3550-50E/MS uses an MSOP-8 surface-mount package and supports an operating temperature range of -40 °C to +125 °C. The manufacturer offers the device in MSOP and SOIC package options within the broader MCP3550/1/3 family. The MSOP configuration is useful where PCB area is constrained but a conventional through-hole-compatible industrial design is not required.
At 12.5 samples per second, the converter is suited to slowly changing measurements such as resistive bridges, thermocouple interfaces, industrial pressure transducers, and environmental sensors. Its differential input can help reject common-mode disturbances when the source is balanced and the analog front end is designed accordingly. It is less suitable for waveform capture, motor-control feedback, or other signals requiring sampling rates above the kilohertz range.
Circuit design should follow the manufacturer datasheet for input filtering, reference voltage, bypass capacitance, and digital-interface implementation. Because sigma-delta converters reject out-of-band noise through digital filtering, the input network should suppress interference near the conversion bandwidth without unnecessarily increasing noise in the measured signal band.
This product overview combines the manufacturer specifications with practical guidance for sensor acquisition, package selection, replacement planning, and PCB implementation. It also highlights where pin-compatible family members differ in conversion rate and where a direct drop-in substitution must be selected against the complete electrical requirements of the original design.
Bộ thay thế dễ dàng lắp đặt cho MCP3550-50E/MS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MCP3550-60E/MS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCP3550-50E/MS Tỷ lệ tối đa & tính chất điện
| ADC Resolution | 22 bit |
| Conversion Rate | 12.5 samples/s |
| Number of Channels | 1 channel |
| Architecture | Delta-sigma |
| Input Type | Fully differential |
| Input Logic | Single-ended or differential signal conditioning |
| Maximum Supply Voltage | 4.5 V |
| Digital Interface | SPI |
| Khoảng nhiệt độ hoạt động | -40 °C to +125 °C |
| Hộp | 8-pin MSOP |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MCP3550-50E/MS 8-pin msop
Cấu hình chân cho MCP3550-50E/MS (8-pin msop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP3550-50E/MS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP3550-50E/MS phù hợp cho 6 Áp dụngs: Industrial Pressure Transducers, Temperature and Humidity Monitoring, Process-Control Instrumentation, Battery-Powered Sensor Nodes, Precision Bridge Measurement, Data Acquisition and Test Equipment.
Industrial Pressure Transducers
The MCP3550-50E/MS fits slow industrial pressure measurements where high resolution and low analog noise matter more than rapid sampling. Its 22-bit converter resolves small changes in a conditioned bridge or pressure-sensor output, while the fully differential input helps preserve the useful difference between two sensing nodes. At 12.5 samples per second, it can support monitoring and alarm functions without the power and timing demand of a high-speed ADC. The principal design consideration is filtering: place the differential input network close to the MSOP-8 pins and select components according to the manufacturer’s sensor-interface guidance.
Được đề xuất
Temperature and Humidity Monitoring
MCP3550-50E/MS is appropriate for thermal and environmental sensors whose values change slowly. A 22-bit conversion result provides ample code density for calibrated temperature or humidity channels, and the 12.5-sample-per-second rate is adequate for supervisory, HVAC, storage, and environmental-control systems. Its differential input can be driven by a resistive network or a suitably conditioned sensor bridge. Designers should allow adequate settling time after sensor changes and use input filtering that preserves slow, meaningful variations rather than unnecessarily narrowing the measurement bandwidth.
Được đề xuất
Process-Control Instrumentation
The MCP3550-50E/MS supports process-control measurements in which a transmitter presents a slowly changing differential voltage. Its 22-bit resolution improves sensitivity to small process variations, while the fully differential input reduces sensitivity to common-mode voltage when the source and front end are properly balanced. The MSOP-8 package also supports compact multi-channel measurement boards. Keep analog routing short, use a quiet reference arrangement, and implement digital filtering or averaging only after confirming that the resulting response meets the control-loop bandwidth requirement.
Được đề xuất
Battery-Powered Sensor Nodes
MCP3550-50E/MS can serve as the measurement converter in a battery-powered industrial or environmental sensor node because it is designed as a low-power, single-channel sigma-delta ADC. Its 12.5-sample-per-second conversion rate matches slowly varying sensor readings, allowing the system controller to remain in a low-activity state between measurements. The differential analog input also supports compact, balanced sensor interfaces. Power budgeting must include both the ADC and its support circuitry, and the final sampling interval should be selected to preserve useful sensor response without wasting energy.
Được đề xuất
Precision Bridge Measurement
The MCP3550-50E/MS is well matched to resistive bridge measurements because it provides 22-bit resolution and a fully differential input in a compact 8-pin MSOP package. Differential excitation and sensing can reduce sensitivity to supply variation and common-mode noise, provided the bridge and instrumentation are balanced correctly. The converter’s digital filtering suppresses noise outside its useful measurement band. For best results, follow the input-biasing and filtering guidance in the manufacturer datasheet and avoid placing high-current or switching traces directly beside the sensitive analog pins.
Được đề xuất
Data Acquisition and Test Equipment
MCP3550-50E/MS can provide accurate low-speed measurements in laboratory and industrial data-acquisition systems. Its 22-bit resolution is useful when the goal is to capture small analog changes with a limited sample rate, while the 12.5-sample-per-second operation avoids the complexity and power burden of a high-speed converter. A microcontroller or test controller can read the results over SPI and apply calibration, filtering, or logging. Ensure the analog source can settle within the conversion timing and do not use this device where waveform features require significantly faster acquisition.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP3550-50E/MS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP3550-60E/MS |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-pin MSOP | 8-pin MSOP - same |
| ADC Resolution | 22 bit | 22 bit |
| Conversion Rate | 12.5 samples/s | 13.75 samples/s |
| Number of Channels | 1 channel | 1 channel |
| Architecture | Delta-sigma | Delta-sigma |
| Input Configuration | Fully differential | Fully differential |
| Digital Interface | SPI | SPI |
| Maximum Supply Voltage | 4.5 V | 4.5 V |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C |
Bảo phân biệt quan trọng
- Lower conversion rate supports a 12.5-sample-per-second measurement mode (vsMCP3550-60E/MS)
- Compact MSOP implementation for space-constrained sensor boards (vsMCP3550-50E/SN)
- High-resolution conversion for slow precision signals (vsMCP3550-60E/MS)
Ghi chú thiết kế
Place the differential input traces, reference components, and bypass capacitors close to their corresponding MCP3550-50E/MS pins. Route the analog pair as a compact, balanced pair and keep switching-regulator, relay, and high-current return paths away from the input and reference nodes. The MSOP-8 land pattern offers little routing space, so component placement and via use should be decided before the analog and digital sections are routed.
Design the analog filter for the slow measurement bandwidth rather than copying a generic RC value. Sigma-delta digital filtering rejects many out-of-band disturbances, but excessive analog filtering can increase settling time or reduce useful signal amplitude. Begin with the input-network guidance in Microchip Data Sheet 20001950F and validate attenuation, noise, and transient response in the assembled board. Maintain symmetry where the source is differential to avoid converting common-mode noise into an input error.
Use a quiet, low-impedance supply and reference arrangement because conversion accuracy ultimately depends on the analog operating conditions. Place required bypass capacitors next to the supply pins and decouple any reference node according to the manufacturer recommendations. Check the exact supply range, analog and digital current consumption, and power-up sequence before finalizing the board. Do not infer equivalent input impedance or settling behavior from a different MCP3550 speed variant.
Do not confuse the MSOP-8 MCP3550-50E/MS with MCP3550-50E/SN, which uses an 8-pin SOIC package, or assume that a 12.5-sample-per-second converter can capture high-frequency waveforms. Also distinguish electrical variants from ordering suffixes such as the T tape-and-reel code. Verify the manufacturer pin table, package drawing, conversion timing, and filtering requirements before approving a substitute or laying out a replacement board.
Thông tin tuân thủ
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact MCP3550-50E/MS order code. Confirm compliance with the manufacturer using the ordering code and required production volume.