MCP6002-E/MS - Dual 1 MHz Low-Power Op Amp | Microchip
MPN: MCP6002-E/MS ✓ Hoạt độngMCP6002-E/MS Tóm tắt
An operational amplifier is an active analog component that amplifies the voltage difference between its two inputs while using negative feedback to set the closed-loop gain. The MCP6002 belongs to the general-purpose operational-amplifier hierarchy, combining rail-to-rail signal handling, low quiescent consumption, and moderate bandwidth. This makes it practical for battery-operated instrumentation, low-voltage sensor interfaces, buffer stages, and general analog signal conditioning.
Key characteristics include two amplifier channels in one package, a 1 MHz typical gain-bandwidth product, and a 100 uA typical quiescent current. Rail-to-rail inputs allow signals close to either supply rail to be sensed without requiring a separate common-mode reference. Rail-to-rail outputs increase usable output swing, although the datasheet should be consulted for the exact output-voltage limits and load-dependent behavior. The 1.8 V minimum supply supports low-energy systems, while operation up to 5.5 V accommodates common 3.3 V and 5 V rails.
The MCP6002 combines two general-purpose amplifiers in one MSOP package, reducing component count and board area compared with separate single-channel devices. Its 1 MHz bandwidth is suitable for moderate-frequency instrumentation rather than high-speed signal paths. The low 100 uA typical quiescent current reduces standby demand in battery-powered designs. Because gain-bandwidth product, noise, slew rate, common-mode range, output swing, and stability behavior determine practical performance, those parameters should be checked against the required signal bandwidth and load before finalizing a design.
Typical applications include low-voltage sensor conditioning, dual-channel filtering, microphone or audio preamplification at low frequencies, current-to-voltage conversion, and general-purpose buffering. The dual configuration is especially useful when two related analog signals must be amplified with matching device characteristics. A single package can also simplify layout by placing both channels near one another, although each channel still requires correct bypassing and stable feedback-network placement.
For implementation, place the supply bypass capacitor close to the positive and ground pins and route each output to its load with a path that minimizes parasitic capacitance. Do not assume full rail-to-rail output under every load; use the output-voltage limits and capacitive-load stability information in the MCP6002 datasheet. Check input and output common-mode boundaries, maximum differential input voltage, operating temperature, and noise requirements during sign-off.
This product page combines the manufacturer specifications with package, pricing-record, replacement, and practical design guidance. It emphasizes the MCP6002-E/MS distinctions that matter when selecting a dual low-power amplifier for low-voltage analog systems, including the 1 MHz bandwidth, 100 uA typical quiescent current, rail-to-rail operation, and 8-lead MSOP implementation.
Bộ thay thế dễ dàng lắp đặt cho MCP6002-E/MS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCP6002-E/MS (cùng hình factor và footprint) — khác nhau ở Package, Input Common-Mode Range, Output Swing, Product Type, Supply Voltage Range.
MCP6002-I/MS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MCP6002T-I/MS
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6002-E/MS Tỷ lệ tối đa & tính chất điện
| Product Type | Dual operational amplifier |
| Amplifier Classification | General-purpose amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Typical Gain-Bandwidth Product | 1 MHz |
| Typical Quiescent Current | 100 uA |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Hộp | 8-lead MSOP |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MCP6002-E/MS 8-lead msop
Cấu hình chân cho MCP6002-E/MS (8-lead msop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP6002-E/MS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP6002-E/MS phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Signal Conditioning, Low-Voltage Current-to-Voltage Conversion, Dual-Channel Audio Preamplification, Active Filtering and Buffering, Portable Industrial Control Interface, Low-Power IoT Signal Conditioning.
Battery-Powered Sensor Signal Conditioning
The MCP6002-E/MS fits low-energy sensor interfaces because its 1.8 V minimum supply and 100 uA typical quiescent current reduce the burden on a small battery. Rail-to-rail inputs allow the amplifier to sense signals near either supply rail, while the dual package can condition two related channels. Each amplifier can use a resistive gain network, followed by an anti-alias filter formed to suit the 1 MHz gain-bandwidth product. The designer should verify sensor output range, common-mode boundaries, offset, noise, and load current before selecting resistor values and filtering requirements.
Được đề xuất
Low-Voltage Current-to-Voltage Conversion
The MCP6002-E/MS can implement two current-to-voltage conversion channels for low-voltage sensors when its 1.8 V to 5.5 V operating range matches the system rail. A transimpedance stage places feedback resistance between the inverting input and output, while the non-inverting input returns to a suitable reference. The 1 MHz gain-bandwidth product constrains practical transimpedance bandwidth through the interaction of feedback resistance, input capacitance, and amplifier noise gain. With 100 uA typical quiescent current, the device also supports compact battery-powered measurement circuits where dual-channel conversion improves board utilization.
Được đề xuất
Dual-Channel Audio Preamplification
The MCP6002-E/MS is suitable for dual-channel, low-level audio preamplification when modest bandwidth and low power are more important than low-noise studio performance. Two amplifiers in one 8-lead MSOP provide matched device characteristics for left and right channels and conserve board area. The 1.8 V to 5.5 V supply range supports portable audio systems, while rail-to-rail inputs help accommodate microphone or line-level signals that move across the available supply range. Verify the input noise density, gain error, output swing, and capacitive-load stability in the datasheet before using it with microphones, tone controls, or speaker-driver inputs.
Được đề xuất
Active Filtering and Buffering
The MCP6002-E/MS can form two independent active-filter or buffer stages where a 1 MHz gain-bandwidth product is sufficient for the signal band. Rail-to-rail input and output capability improves signal utilization in compact low-voltage systems, while the 8-lead MSOP supports dense analog layouts. Each channel requires stable feedback-component placement and normal bypassing. Because the available bandwidth changes with closed-loop noise gain, filter component selection should account for closed-loop gain and the datasheet's gain-bandwidth and stability information rather than treating 1 MHz as a fixed usable cutoff frequency.
Được đề xuất
Portable Industrial Control Interface
The MCP6002-E/MS is applicable to compact industrial measurement and control interfaces that operate from a 1.8 V, 3.3 V, or 5 V rail. Its dual-channel arrangement can amplify two sensor inputs or provide a signal and buffered-reference combination within a compact instrument. The 100 uA typical quiescent current is useful in distributed or handheld equipment, and rail-to-rail operation expands usable input range. Industrial use still requires validation of operating temperature, supply tolerance, transient response, electromagnetic interference susceptibility, and output behavior over the actual load range.
Được đề xuất
Low-Power IoT Signal Conditioning
The MCP6002-E/MS can condition low-frequency sensor outputs in IoT edge devices where the complete analog path must operate from a small energy budget. Its 1.8 V to 5.5 V supply range suits low-voltage microcontrollers and radio circuits, while 100 uA typical quiescent current limits standby demand. Two channels allow a system to amplify paired measurements without using two separate packages, and rail-to-rail inputs are useful near the limits of a reduced supply. Confirm whether the device remains active during the system's duty cycle and validate offset, noise, and wake-up settling against the acquisition requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP6002-E/MS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP6002-I/MS | MCP6002T-I/MS |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-lead MSOP | 8-lead MSOP | 8-lead MSOP |
| Number of Channels | 2 channels | 2 channels | 2 channels |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Typical Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz |
| Typical Quiescent Current | 100 uA | 100 uA | 100 uA |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Swing | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Temperature Grade | E ordering suffix | I ordering suffix | I ordering suffix with tape-and-reel ordering code |
Bảo phân biệt quan trọng
- Combines two rail-to-rail amplifier channels in one compact MSOP (vsMCP6001-E/MS)
- Offers the same documented core performance as the supported family alternatives (vsMCP6002-I/MS)
- Supports compact dual-channel acquisition without using two single packages (vsMCP6004-E/MS)
Ghi chú thiết kế
Place a local bypass capacitor between the supply and ground pins, with the connection to the MCP6002-E/MS kept as short as practical. Treat 100 uA as the typical quiescent current rather than a maximum-load figure: output current, input common-mode voltage, and output swing also affect supply demand. Calculate the worst-case dissipation from the actual supply voltage, output voltage, and load current before checking the MSOP's allowable temperature rise.
Route each feedback component directly between its amplifier output and inverting input, and keep the non-inverting-input track away from output and switching nodes. Because the typical gain-bandwidth product is only 1 MHz, stray capacitance around high-impedance inputs or feedback nodes can alter stability and bandwidth. The two channels share one package and supply but should retain symmetric, short routing so their signal paths acquire similar parasitic loading.
Do not interpret rail-to-rail input or output as exact rail-to-rail operation at every supply voltage and load. Check the common-mode and output-swing plots in the MCP6002 datasheet, especially when the signal approaches a supply rail or the output drives a heavy load. Also confirm the operating-temperature grade and absolute maximum ratings for the MCP6002-E/MS ordering suffix before using it outside the intended environmental range.
The 1 MHz gain-bandwidth product limits closed-loop bandwidth as noise gain increases, so a 1 MHz amplifier does not provide 1 MHz of usable closed-loop bandwidth at every gain setting. For filtering or instrumentation applications, calculate the closed-loop bandwidth, phase margin, and settling behavior from the intended feedback network. Use a stable feedback configuration and verify capacitive-load limitations with the manufacturer guidance.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was found for the exact MCP6002-E/MS ordering code. Confirm the required declarations with the manufacturer or the supplier handling the purchase request.