Microchip Technology

MCP6002-E/MS - Dual 1 MHz Low-Power Op Amp | Microchip

料号: MCP6002-E/MS ✓ 量产中
1.8 V to 5.5 V Vdss 100 uA Id 8-lead MSOP Package
最小起订量: 1 |

MCP6002-E/MS 概述

The Microchip Technology MCP6002-E/MS is a dual general-purpose operational amplifier with a typical gain-bandwidth product of 1 MHz, a typical quiescent current of 100 uA, and a 1.8 V to 5.5 V supply range. The device provides rail-to-rail input and output operation and is packaged in an 8-lead MSOP. Its two amplifiers make it suitable for compact dual-channel analog signal-conditioning circuits that require low power and a low operating voltage.

An operational amplifier is an active analog component that amplifies the voltage difference between its two inputs while using negative feedback to set the closed-loop gain. The MCP6002 belongs to the general-purpose operational-amplifier hierarchy, combining rail-to-rail signal handling, low quiescent consumption, and moderate bandwidth. This makes it practical for battery-operated instrumentation, low-voltage sensor interfaces, buffer stages, and general analog signal conditioning.

Key characteristics include two amplifier channels in one package, a 1 MHz typical gain-bandwidth product, and a 100 uA typical quiescent current. Rail-to-rail inputs allow signals close to either supply rail to be sensed without requiring a separate common-mode reference. Rail-to-rail outputs increase usable output swing, although the datasheet should be consulted for the exact output-voltage limits and load-dependent behavior. The 1.8 V minimum supply supports low-energy systems, while operation up to 5.5 V accommodates common 3.3 V and 5 V rails.

The MCP6002 combines two general-purpose amplifiers in one MSOP package, reducing component count and board area compared with separate single-channel devices. Its 1 MHz bandwidth is suitable for moderate-frequency instrumentation rather than high-speed signal paths. The low 100 uA typical quiescent current reduces standby demand in battery-powered designs. Because gain-bandwidth product, noise, slew rate, common-mode range, output swing, and stability behavior determine practical performance, those parameters should be checked against the required signal bandwidth and load before finalizing a design.

Typical applications include low-voltage sensor conditioning, dual-channel filtering, microphone or audio preamplification at low frequencies, current-to-voltage conversion, and general-purpose buffering. The dual configuration is especially useful when two related analog signals must be amplified with matching device characteristics. A single package can also simplify layout by placing both channels near one another, although each channel still requires correct bypassing and stable feedback-network placement.

For implementation, place the supply bypass capacitor close to the positive and ground pins and route each output to its load with a path that minimizes parasitic capacitance. Do not assume full rail-to-rail output under every load; use the output-voltage limits and capacitive-load stability information in the MCP6002 datasheet. Check input and output common-mode boundaries, maximum differential input voltage, operating temperature, and noise requirements during sign-off.

This product page combines the manufacturer specifications with package, pricing-record, replacement, and practical design guidance. It emphasizes the MCP6002-E/MS distinctions that matter when selecting a dual low-power amplifier for low-voltage analog systems, including the 1 MHz bandwidth, 100 uA typical quiescent current, rail-to-rail operation, and 8-lead MSOP implementation.

直接替换替代料: MCP6002-E/MS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MCP6002-E/MS (相同外形与封装尺寸) ——差异在于 Package, Input Common-Mode Range, Output Swing, Product Type, Supply Voltage Range.

Microchip Technology
Input Common-Mode Range: Rail-to-rail
Output Swing: Rail-to-rail
Product Type: Dual general-purpose operational amplifier
NI
Package: 8-VSSOP / 8-MSOP (TVSP, 0.110", 2.80 mm Width)

MCP6002-I/MS

✅ 直接替换
Microchip Technology
📦 8-lead MSOP
Dual general-purpose operational amplifier · 2 channels · 1.8 V to 6 V · Rail-to-rail · Rail-to-rail · 1 MHz typical · 100 microamperes typical · 8-lead MSOP

联系询价

查看数据手册 →

MCP6002T-I/MS

✅ 直接替换 ⚠️ 规格未核验
📦 8-lead MSOP
Core electrical ratings remain within 100% for the 1.8 V to 5.5 V supply, 1 MHz typical gain-bandwidth product, and 100 uA typical quiescent current; the T suffix identifies tape-and-reel ordering.

📋 参考替代料(不在目录中)

MCP6002-E/MS 最大额定值与电气特性

Product Type Dual operational amplifier
Amplifier Classification General-purpose amplifier
Number of Channels 2 channels
Supply Voltage Range 1.8 V to 5.5 V
Typical Gain-Bandwidth Product 1 MHz
Typical Quiescent Current 100 uA
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
封装 8-lead MSOP
安装类型 Surface mount

MCP6002-E/MS 8-lead msop 引脚配置指南

MCP6002-E/MS(8-lead msop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

MCP6002-E/MS 的 8-lead msop 封装引脚图

暂无详细引脚数据: MCP6002-E/MS.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MCP6002-E/MS 适用于 6 应用s: Battery-Powered Sensor Signal Conditioning, Low-Voltage Current-to-Voltage Conversion, Dual-Channel Audio Preamplification, Active Filtering and Buffering, Portable Industrial Control Interface, Low-Power IoT Signal Conditioning.

🔋

Battery-Powered Sensor Signal Conditioning

The MCP6002-E/MS fits low-energy sensor interfaces because its 1.8 V minimum supply and 100 uA typical quiescent current reduce the burden on a small battery. Rail-to-rail inputs allow the amplifier to sense signals near either supply rail, while the dual package can condition two related channels. Each amplifier can use a resistive gain network, followed by an anti-alias filter formed to suit the 1 MHz gain-bandwidth product. The designer should verify sensor output range, common-mode boundaries, offset, noise, and load current before selecting resistor values and filtering requirements.

⚡

Low-Voltage Current-to-Voltage Conversion

The MCP6002-E/MS can implement two current-to-voltage conversion channels for low-voltage sensors when its 1.8 V to 5.5 V operating range matches the system rail. A transimpedance stage places feedback resistance between the inverting input and output, while the non-inverting input returns to a suitable reference. The 1 MHz gain-bandwidth product constrains practical transimpedance bandwidth through the interaction of feedback resistance, input capacitance, and amplifier noise gain. With 100 uA typical quiescent current, the device also supports compact battery-powered measurement circuits where dual-channel conversion improves board utilization.

🎧

Dual-Channel Audio Preamplification

The MCP6002-E/MS is suitable for dual-channel, low-level audio preamplification when modest bandwidth and low power are more important than low-noise studio performance. Two amplifiers in one 8-lead MSOP provide matched device characteristics for left and right channels and conserve board area. The 1.8 V to 5.5 V supply range supports portable audio systems, while rail-to-rail inputs help accommodate microphone or line-level signals that move across the available supply range. Verify the input noise density, gain error, output swing, and capacitive-load stability in the datasheet before using it with microphones, tone controls, or speaker-driver inputs.

🔧

Active Filtering and Buffering

The MCP6002-E/MS can form two independent active-filter or buffer stages where a 1 MHz gain-bandwidth product is sufficient for the signal band. Rail-to-rail input and output capability improves signal utilization in compact low-voltage systems, while the 8-lead MSOP supports dense analog layouts. Each channel requires stable feedback-component placement and normal bypassing. Because the available bandwidth changes with closed-loop noise gain, filter component selection should account for closed-loop gain and the datasheet's gain-bandwidth and stability information rather than treating 1 MHz as a fixed usable cutoff frequency.

🏭

Portable Industrial Control Interface

The MCP6002-E/MS is applicable to compact industrial measurement and control interfaces that operate from a 1.8 V, 3.3 V, or 5 V rail. Its dual-channel arrangement can amplify two sensor inputs or provide a signal and buffered-reference combination within a compact instrument. The 100 uA typical quiescent current is useful in distributed or handheld equipment, and rail-to-rail operation expands usable input range. Industrial use still requires validation of operating temperature, supply tolerance, transient response, electromagnetic interference susceptibility, and output behavior over the actual load range.

🧩

Low-Power IoT Signal Conditioning

The MCP6002-E/MS can condition low-frequency sensor outputs in IoT edge devices where the complete analog path must operate from a small energy budget. Its 1.8 V to 5.5 V supply range suits low-voltage microcontrollers and radio circuits, while 100 uA typical quiescent current limits standby demand. Two channels allow a system to amplify paired measurements without using two separate packages, and rail-to-rail inputs are useful near the limits of a reduced supply. Confirm whether the device remains active during the system's duty cycle and validate offset, noise, and wake-up settling against the acquisition requirements.

推荐产品汇总

MCP6001-E/MS Single-channel MCP6001-family companion when one conditioned channel is sufficient 用于: Battery-Powered Sensor Signal Conditioning, Low-Voltage Current-to-Voltage Conversion, Dual-Channel Audio Preamplification, Active Filtering and Buffering, Portable Industrial Control Interface, Low-Power IoT Signal Conditioning MCP6004-E/MS Four-channel MCP6004-family option for multi-sensor systems 用于: Battery-Powered Sensor Signal Conditioning, Low-Voltage Current-to-Voltage Conversion, Dual-Channel Audio Preamplification, Active Filtering and Buffering, Portable Industrial Control Interface, Low-Power IoT Signal Conditioning
What are the key specifications of MCP6002-E/MS that engineers should know?
The MCP6002-E/MS is a dual general-purpose operational amplifier with 1.8 V to 5.5 V supply operation, 1 MHz typical gain-bandwidth product, 100 uA typical quiescent current, and rail-to-rail input and output capability in an 8-lead MSOP. According to the Microchip Technology MCP6002 product page, these characteristics position the device for low-voltage, low-power signal-conditioning systems requiring two amplifier channels in one package.
What is the operating voltage of MCP6002-E/MS?
The MCP6002-E/MS operates from 1.8 V to 5.5 V. According to Microchip Technology's MCP6002 product page, the dual amplifier is intended for low-voltage systems and can operate from a single 1.8 V rail as well as common 3.3 V and 5 V supplies. Confirm signal amplitudes and output-swing requirements against the datasheet for the specific supply and load conditions.
What is MCP6002-E/MS and what is an operational amplifier?
The MCP6002-E/MS is a dual, 1 MHz, low-power operational amplifier in an 8-lead MSOP. An operational amplifier uses high-gain differential amplification with negative feedback to set precision, stable circuit behavior. According to Microchip Technology, the MCP6002 supports rail-to-rail inputs and outputs over its 1.8 V to 5.5 V operating range.
Where can I download the MCP6002 datasheet PDF?
The MCP6002 manufacturer information is available through Microchip Technology's official product page at https://www.microchip.com/en-us/product/MCP6002. The device is also listed as a 28-page MCP6002 datasheet PDF at https://www.alldatasheet.com/datasheet-pdf/pdf/195202/MICROCHIP/MCP6002.html. Use the manufacturer document for final electrical limits, pin descriptions, test conditions, and application guidance.
Where can I find the MCP6002 pinout?
The MCP6002 pinout and pin descriptions should be taken from the MCP6002 manufacturer datasheet associated with the Microchip product page. The MCP6002-E/MS is specified in an 8-lead MSOP package. Because the exact lead assignments are not reproduced on the manufacturer product page, use the pin-description table in the datasheet when assigning PCB tracks and verifying dual-channel layout.
How much current does MCP6002-E/MS consume?
The MCP6002-E/MS has a typical quiescent current of 100 uA. According to Microchip Technology's MCP6002 product page, this low standby demand is a central advantage for battery-operated and energy-conscious analog circuits. Actual supply-current use also depends on supply voltage, output swing, load, and the operating state of each amplifier channel.
What is the gain-bandwidth product of MCP6002-E/MS?
The MCP6002-E/MS has a typical gain-bandwidth product of 1 MHz. According to the Microchip Technology MCP6002 product page, that bandwidth is intended for general-purpose, moderate-frequency analog applications. For active filters or closed-loop amplifiers, verify the required signal frequency, gain, phase margin, and capacitive-load stability against the datasheet.
Is MCP6002-E/MS suitable for battery-powered sensor conditioning?
Yes, the MCP6002-E/MS is suitable for many battery-powered sensor-conditioning designs. Its 1.8 V minimum supply and 100 uA typical quiescent current support low-voltage operation, while dual rail-to-rail inputs help sense signals near the supply rails. The 1 MHz bandwidth is appropriate for moderate-frequency sensors, and the 8-lead MSOP reduces board area.
Where can I buy MCP6002-E/MS online and what is its price?
Use the Request a Quote form on this XAIPART product page to request MCP6002-E/MS pricing, stock confirmation, and lead time. The structured price record on this page contains a unit-price reference but no qualifying current quantity-break table, so live purchasing terms should be confirmed through the quote form. The form is the appropriate route for an exact MPN and package request.
Is MCP6002-E/MS in stock and what is its lead time?
MCP6002-E/MS availability and lead time should be confirmed through the Request a Quote form on this page. Distributor listings indicate market availability, but they do not establish the quantity currently available for the exact suffix under every purchasing condition. Include the required quantity, date code, and acceptable shipping destination when submitting the request.
What is the lead time for MCP6002-E/MS?
The current lead time for MCP6002-E/MS is obtained through the Request a Quote form on this page. A firm lead time depends on requested quantity, stock position, and shipment destination rather than on the device's fixed electrical specifications. Provide the complete MPN MCP6002-E/MS and your required delivery schedule so procurement can confirm the appropriate commitment.
What can replace MCP6002-E/MS?
The closest documented same-brand replacement is MCP6002-I/MS, which uses the same 8-lead MSOP format and belongs to the same MCP6002 family. Because the suffix and temperature-grade requirements affect qualification, verify the complete datasheet and operating-temperature limits before substitution. The Request a Quote form can confirm availability of the exact replacement MPN.
Is MCP6002-E/MS the same as MCP6002-I/MS?
The MCP6002-E/MS and MCP6002-I/MS are members of the same MCP6002 dual-amplifier family and share the 8-lead MSOP package, but their ordering suffixes identify different device classifications. The exact temperature-grade limits must be checked in the manufacturer datasheet before treating them as equivalent. Both have the same principal 1.8 V to 5.5 V, 1 MHz, and 100 uA typical ratings.
What is the best drop-in replacement for MCP6002-E/MS?
MCP6002-I/MS is the best-supported drop-in candidate because it is an MCP6002-family device in the same 8-lead MSOP package. No cross-brand equivalent could be confirmed as both pin-to-pin and parametrically compatible from the available cross-reference information. Review input range, output swing, bandwidth, offset, noise, slew rate, temperature grade, and stability before approving a replacement.
MCP6002-E/MS vs MCP6002-I/MS: which is better for a low-voltage application?
Choose MCP6002-E/MS when its documented temperature grade matches the application's environmental requirements; otherwise MCP6002-I/MS may be the better fit. Both are dual 1 MHz general-purpose amplifiers with 100 uA typical quiescent current and rail-to-rail operation in an 8-lead MSOP. The decisive distinction is the ordering suffix and its temperature-grade specification, not the core signal-conditioning function.
What is the best Texas Instruments equivalent for MCP6002-E/MS?
No Texas Instruments dual amplifier can be confirmed as a true drop-in equivalent for MCP6002-E/MS from the available compatibility information. The discussed TLV9062 and TLV9002 are dual rail-to-rail amplifiers, but package and detailed electrical comparisons are required before PCB reuse. The MCP6002's 1 MHz typical bandwidth, 100 uA typical quiescent current, and 8-lead MSOP footprint must all be matched.
Does the MCP6002-E/MS support rail-to-rail input and output operation?
Yes, the MCP6002-E/MS supports rail-to-rail input and output operation. According to Microchip Technology, the MCP6002 is a dual general-purpose amplifier with rail-to-rail input and output over its low-voltage operating range. Rail-to-rail behavior does not mean the output reaches the exact supply rails, so check the output-swing limits for the selected load.

工程参考数据: MCP6002-E/MS ——对比、设计指导和合规信息。

选型指南

Choose MCP6002-E/MS for compact, low-voltage analog designs that need two general-purpose amplifiers, a 1.8 V to 5.5 V supply range, rail-to-rail input and output operation, and approximately 100 uA typical quiescent current. MCP6002-I/MS is the closest supported family alternative when its ordering suffix matches the required temperature grade and environmental range; the package and principal electrical ratings are unchanged. MCP6002T-I/MS provides the same family construction with tape-and-reel ordering for compatible production workflows. MCP6001-E/MS is preferable only when a single amplifier channel is required, while MCP6004-E/MS is appropriate for four-channel systems. For any substitution, verify exact temperature limits, offset, noise, slew rate, common-mode range, output swing, and stability rather than relying only on the 1 MHz bandwidth and supply rating.

与替代料对比

参数 本产品 MCP6002-I/MS MCP6002T-I/MS
Brand Microchip Technology Microchip Technology Microchip Technology
Package 8-lead MSOP 8-lead MSOP 8-lead MSOP
Number of Channels 2 channels 2 channels 2 channels
Supply Voltage Range 1.8 V to 5.5 V 1.8 V to 5.5 V 1.8 V to 5.5 V
Typical Gain-Bandwidth Product 1 MHz 1 MHz 1 MHz
Typical Quiescent Current 100 uA 100 uA 100 uA
Input Common-Mode Range Rail-to-rail input Rail-to-rail input Rail-to-rail input
Output Swing Rail-to-rail output Rail-to-rail output Rail-to-rail output
Temperature Grade E ordering suffix I ordering suffix I ordering suffix with tape-and-reel ordering code

关键差异点

  • Combines two rail-to-rail amplifier channels in one compact MSOP (对比 MCP6001-E/MS)
  • Offers the same documented core performance as the supported family alternatives (对比 MCP6002-I/MS)
  • Supports compact dual-channel acquisition without using two single packages (对比 MCP6004-E/MS)

设计说明

Place a local bypass capacitor between the supply and ground pins, with the connection to the MCP6002-E/MS kept as short as practical. Treat 100 uA as the typical quiescent current rather than a maximum-load figure: output current, input common-mode voltage, and output swing also affect supply demand. Calculate the worst-case dissipation from the actual supply voltage, output voltage, and load current before checking the MSOP's allowable temperature rise.

Route each feedback component directly between its amplifier output and inverting input, and keep the non-inverting-input track away from output and switching nodes. Because the typical gain-bandwidth product is only 1 MHz, stray capacitance around high-impedance inputs or feedback nodes can alter stability and bandwidth. The two channels share one package and supply but should retain symmetric, short routing so their signal paths acquire similar parasitic loading.

Do not interpret rail-to-rail input or output as exact rail-to-rail operation at every supply voltage and load. Check the common-mode and output-swing plots in the MCP6002 datasheet, especially when the signal approaches a supply rail or the output drives a heavy load. Also confirm the operating-temperature grade and absolute maximum ratings for the MCP6002-E/MS ordering suffix before using it outside the intended environmental range.

The 1 MHz gain-bandwidth product limits closed-loop bandwidth as noise gain increases, so a 1 MHz amplifier does not provide 1 MHz of usable closed-loop bandwidth at every gain setting. For filtering or instrumentation applications, calculate the closed-loop bandwidth, phase margin, and settling behavior from the intended feedback network. Use a stable feedback configuration and verify capacitive-load limitations with the manufacturer guidance.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was found for the exact MCP6002-E/MS ordering code. Confirm the required declarations with the manufacturer or the supplier handling the purchase request.

相关搜索

mcp6002 datasheet mcp6002 op amp mcp6002 pinout mcp6002 op amp datasheet mcp6002 spice model mcp6002 op amp schematic mcp6002 price mcp6002 equivalent mcp6002 module MCP6002-E/MS datasheet pdf MCP6002-E/MS pinout MCP6002-E/MS equivalent MCP6002-E/MS replacement MCP6002-E/MS 8-MSOP Microchip MCP6002-E/MS

相关元器件 & 术语

Microchip Technology MCP6002-E/MS MCP6002 MCP6002-I/MS MCP6002T-I/MS MCP6001-E/MS MCP6004-E/MS operational amplifier general-purpose amplifier dual amplifier analog signal conditioning rail-to-rail input rail-to-rail output gain-bandwidth product quiescent current 1 MHz 100 uA 1.8 V to 5.5 V 8-lead MSOP MSOP package family surface-mount package battery-powered sensor conditioning current-to-voltage conversion active filtering IoT signal conditioning
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情