MCP603T-I/SN - 2.8MHz Low-Power R-R Op Amp | Microchip
MPN: MCP603T-I/SN ✓ Hoạt độngMCP603T-I/SN Tóm tắt
An operational amplifier, or op amp, is a voltage-gain element that compares its two input terminals and drives its output toward a higher voltage when the noninverting input exceeds the inverting input. The MCP603 belongs to the CMOS operational-amplifier hierarchy, combining low power consumption and rail-to-rail output capability in a compact analog signal-conditioning package.
The MCP603T-I/SN provides a 2.8 MHz gain-bandwidth product for moderate-frequency amplification and active filtering. Its typical operating current of 230 µA reduces the supply burden in battery-operated equipment, while offset voltage below 2 mV supports accurate signal conditioning around a defined common-mode level. A listed slew rate of 4.5 V/µs provides useful response for low-frequency control, sensing, and buffering applications.
Microchip's advanced CMOS implementation supports low bias current and low operating power, making the amplifier suitable for portable and low-energy systems. The MCP603 can be configured for noninverting, inverting, summing, filtering, and voltage-following circuits. Designers must still account for output-drive capability, input common-mode range, noise, stability, and the limits of a single low-voltage supply when selecting external resistors and capacitors.
Typical uses include sensor-signal conditioning, portable instrumentation, low-power data acquisition, industrial control interfaces, analog sensor buffers, and general-purpose voltage amplification. In each case, the 2.8 MHz bandwidth and 230 µA typical operating current provide a useful balance between signal speed and energy use, while the SOIC-8 package supports conventional surface-mount assembly.
The most important design consideration is power-supply decoupling. Place the required input and output bypass capacitors close to the device pins, keep feedback loops compact, and confirm that source and load impedances remain compatible with stable closed-loop operation. Review the manufacturer's pin description and recommended application circuit before finalizing PCB routing.
This product page combines the manufacturer specifications with practical selection guidance, package details, sourcing instructions, and a qualified drop-in comparison. It supports faster engineering decisions by separating confirmed electrical characteristics from application-specific design requirements.
Bộ thay thế dễ dàng lắp đặt cho MCP603T-I/SN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCP603T-I/SN (cùng hình factor và footprint) — khác nhau ở Output Swing, Slew Rate.
MCP603-I/SN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MCP603T-I/SN Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single general-purpose operational amplifier |
| Circuit Count | 1 circuit |
| Technology | CMOS |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 µA |
| Input Offset Voltage | Less than 2 mV typical |
| Slew Rate | 4.5 V/µs |
| Input Bias Current | 20 pA |
| Output Swing | Rail-to-rail output |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 8 pins |
Hướng dẫn cấu hình chân MCP603T-I/SN 8-pin soic
Cấu hình chân cho MCP603T-I/SN (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP603T-I/SN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP603T-I/SN phù hợp cho 6 Áp dụngs: Portable Sensor Signal Conditioning, Industrial Low-Voltage Control Signals, Low-Power Data Acquisition, Active Filtering and Signal Conditioning, Battery-Powered Monitoring Equipment, General-Purpose Analog Buffering.
Portable Sensor Signal Conditioning
The MCP603T-I/SN fits low-power sensor interfaces that require modest bandwidth and low supply demand. Its 230 µA typical operating current limits amplifier overhead in battery-operated equipment, while the 2.8 MHz gain-bandwidth product is suitable for sensors whose useful bandwidth is well below the amplifier limit. Place the device in a noninverting or inverting conditioning stage and verify that the sensor output remains inside the allowable common-mode range. The rail-to-rail output also helps preserve signal swing on a 3.3 V or 5 V rail, although output-current capability and load stability remain important design checks.
Được đề xuất
Industrial Low-Voltage Control Signals
The MCP603T-I/SN is appropriate for buffering and scaling industrial control signals that operate from 2.7 V to 6.0 V. Its industrial temperature option covers -40°C to +85°C, and its 2.8 MHz gain-bandwidth product is more than adequate for common slow analog control loops. The amplifier can drive a downstream converter input or serve as an active filter, but its output-current limit and load stability must be checked against the selected network. Keep feedback traces short and connect bypass capacitors near the supply pins to reduce coupling from switching equipment sharing the enclosure.
Được đề xuất
Low-Power Data Acquisition
The MCP603T-I/SN can provide the analog gain and buffering stage in a compact data-acquisition channel. A 2.8 MHz gain-bandwidth product supports signals extending well beyond conventional slow sensor bandwidth, while the 230 µA typical operating current helps maintain low power when several channels are active. Use the amplifier ahead of an ADC when source impedance requires buffering, and confirm that ADC acquisition timing remains compatible with the amplifier settling behavior. Decouple the 2.7 V to 6.0 V supply locally and use the manufacturer pin table to assign inputs, output, and feedback components correctly.
Được đề xuất
Active Filtering and Signal Conditioning
The MCP603T-I/SN is suitable for first-order or moderate-order active filters when low operating power is important. Its 2.8 MHz gain-bandwidth product provides useful closed-loop bandwidth for filters handling low-frequency sensor, audio-control, or measurement signals. Component tolerances and the amplifier's offset below 2 mV typical directly influence DC accuracy, so precision resistors and suitable capacitors may be needed. Confirm stability with the actual source and load impedances, because the recommended compensation values depend on the selected closed-loop gain and operating frequency.
Được đề xuất
Battery-Powered Monitoring Equipment
The MCP603T-I/SN supports compact monitoring equipment where every milliamp of continuous current affects battery life. Its 230 µA typical operating current and low-voltage CMOS design are useful for always-on analog paths, while the 4.5 V/µs slew rate permits reasonably fast signal transitions. The amplifier should operate within its 2.7 V minimum supply and away from rail limits that would reduce output swing. Evaluate leakage from the surrounding circuit, disable unneeded channels where possible, and use shutdown or a series switch if the application requires a deeper sleep mode than the amplifier itself provides.
Được đề xuất
General-Purpose Analog Buffering
The MCP603T-I/SN works as a voltage follower or unity-gain buffer when a high-impedance source must drive a lower-impedance downstream stage. The rail-to-rail output is advantageous at low supply voltages, and the 230 µA typical operating current avoids making the buffer the dominant system load. Check the capacitive load presented by the following stage and avoid configurations that exceed the amplifier's stability requirements. A short, direct layout from the output to the inverting input is important, while the output should be isolated from sensitive high-impedance nodes to prevent capacitive feedback.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP603T-I/SN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP603-I/SN |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC - same |
| Circuit Count | 1 circuit | 1 circuit |
| Supply Voltage Range | 2.7 V to 6.0 V | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz - 0% difference |
Bảo phân biệt quan trọng
- Low operating current supports portable analog designs (vsMCP603-I/SN)
- Industrial-temperature ordering option (vsMCP603-I/SN)
- Low-voltage rail-to-rail output operation (vsMCP603-I/SN)
Ghi chú thiết kế
Place the input bypass capacitor, output bypass capacitor, and ground connection directly beside the corresponding MCP603T-I/SN pins. Keep traces short and route the return current beneath the device rather than through a long shared path. The 230 µA typical operating current makes the amplifier itself easy to power, but poor grounding can still dominate the noise performance of a sensitive analog stage.
Use the minimum feedback-trace length practical and avoid routing the output beside high-impedance input nodes, where capacitive coupling can create oscillation or disturb small signals. Verify stability with the final source and load impedances and the selected gain. The 2.8 MHz gain-bandwidth product is sufficient for many sensor and control signals, but it does not guarantee stability for every external load.
Do not assume that rail-to-rail output guarantees full input common-mode range. Check the input range and output swing against the actual 2.7 V to 6.0 V supply, and use the manufacturer pin description to avoid assigning pins from a similar amplifier. For low-current designs, also include resistor leakage, sensor bias current, and external circuit consumption in the complete power budget.
Thông tin tuân thủ
No definitive environmental or automotive qualification declarations were identified for this exact ordering code. Use the current Microchip product and material-compliance documentation for production approval.