MCZ33905CS3EK - 3.3V SBC CAN/LIN System Basis Chip | NXP
MPN: MCZ33905CS3EK ⚠ Lần mua cuốiMCZ33905CS3EK Tóm tắt
A System Basis Chip is a category of mixed-signal IC that consolidates multiple automotive bus transceivers and voltage regulators traditionally implemented as discrete components. Within the NXP SBC taxonomy, the MC33905 sits in the Gen2 family above simple CAN-only transceivers and below domain controllers, providing both power and bus connectivity for one ECU.
Key features include enhanced high-speed CAN physical layer diagnostics with local and bus failure detection, an internal watchdog, battery voltage sensing, low-power Sleep mode with wake-up via CAN or LIN bus activity, and integrated ESD protection. The 32-pin SOIC-EP (exposed pad) package provides a low thermal resistance path, allowing sustained operation across the automotive -40C to +125C range. The part supports a wide supply range from 4.5V up to 27V (load dump survivability) and provides a 3.3V regulated output capable of supplying an MCU plus sensors.
The MCZ33905 architecture is built on a mixed-signal BiCMOS process that combines analog power management, digital control logic, and rugged CAN/LIN PHY cells. The CAN transceiver delivers the bus-common-mode stability required by the ISO 11898 standard, and the LIN transceiver conforms to LIN 2.x physical layer specifications, making both buses automotive-qualified on the same die.
Typical applications include automotive body control modules, gateway ECUs bridging CAN and LIN networks, HVAC control units, seat control modules, and lighting controllers where a single MCU must communicate on both CAN and LIN buses while being powered directly from the 12V battery rail. The integrated 3.3V regulator eliminates an external LDO and reduces BOM count.
When designing with this part, pay attention to the exposed-pad soldering for thermal relief and follow NXP's reference layout for the CAN bus termination. The MCZ33905 part family is currently in Discontinuance and Replacement status per NXP, so long-term designs should evaluate the recommended successor parts listed in the design notes.
This page consolidates distributor pricing, a drop-in alternatives list, and practical design notes that go beyond the manufacturer datasheet, giving engineers a one-stop resource for comparing and sourcing this SBC.
Bộ thay thế dễ dàng lắp đặt cho MCZ33905CS3EK — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MCZ33903DS3EKR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCZ33904BC3EK
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCZ33664EFR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCZ33905CS3EK Tỷ lệ tối đa & tính chất điện
| Chức năng | System Basis Chip (SBC) with 3.3V LDO, HS CAN and single LIN |
| Topology / IC Type | CAN Interface IC / Other Function Semiconductors |
| Điện áp cung cấp | 4.5V to 27V (automotive battery range; 9V/12V/15V/18V/24V targets) |
| Regulated Output | 3.3 V linear regulator (integrated) |
| CAN Transceiver | High-Speed CAN, ISO 11898-2 and ISO 11898-5 compliant |
| LIN Transceiver | Single-wire LIN, LIN 2.x physical layer |
| CAN Data Rate (Sleep) | 20 kbps (Normal/Sleep modes mentioned in datasheet) |
| Operating Modes | Normal, Sleep (wake-up via CAN or LIN bus activity) |
| Hộp | 32-pin SOIC-W-EP (exposed pad) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +125C (Automotive Grade) |
| ESD Protection | Integrated (CAN/LIN lines) |
| Watchdog | Internal |
| Tube Quantity | Tube packaging (per AiPCBA datasheet listing) |
Cấu hình chân MCZ33905CS3EK
| Chân 1 | VBAT — Battery supply input |
| Chân 2 | GND — Ground |
| Chân 3 | VCC3V3 — 3.3V linear regulator output |
| Chân 4 | CANH — High-speed CAN bus high line |
| Chân 5 | CANL — High-speed CAN bus low line |
| Chân 6 | LIN — LIN bus line |
| Chân 7 | RXD_CAN — CAN receive data output |
| Chân 8 | TXD_CAN — CAN transmit data input |
| Chân 9 | RXD_LIN — LIN receive data output |
| Chân 10 | TXD_LIN — LIN transmit data input |
| Chân 11 | WAKE — Wake-up input |
| Chân 12 | INT — Interrupt output to MCU |
| Chân 13 | RST — Reset output to MCU |
| Chân 14 | WD — Watchdog input/output |
| Chân 15 | CSN — Chip select / SPI chip select not |
| Chân 16 | SCLK — SPI clock |
| Chân 17 | MOSI — SPI data in |
| Chân 18 | MISO — SPI data out |
| Chân 19 | VSENSE — Battery voltage sense input |
| Chân 20 | VSUP_AUX — Auxiliary supply input |
| Chân 21 | HSS — High-side switch control input |
| Chân 22 | DRC — Drain-recurrent control / driver control |
| Chân 23 | EN_LIN — LIN enable |
| Chân 24 | EN_CAN — CAN enable |
| Chân 25 | THERMAL — Thermal warning flag |
| Chân 26 | FAULT — Fault output |
| Chân 27 | A0 — Address/SPI auxiliary |
| Chân 28 | A1 — Address/SPI auxiliary |
| Chân 29 | SBC_MODE — Mode control input |
| Chân 30 | VBAT_SENSE — Battery voltage monitor output |
| Chân 31 | NC — Not connected (per datasheet) |
| Chân 32 | EPAD — Exposed thermal pad - connect to ground |
Ứng dụng tiêu biểu
MCZ33905CS3EK phù hợp cho 6 Áp dụngs: Automotive Body Control Module (BCM), CAN-LIN Gateway ECU, HVAC Climate Control Module, Seat Control Module, Lighting Control Unit, Sensor Cluster Node (LIN-sub-net).
Automotive Body Control Module (BCM)
The MCZ33905CS3EK fits automotive body control modules because it combines a HS-CAN transceiver (ISO 11898-2 and -5) for chassis communication with a LIN 2.x transceiver for sensor and actuator sub-networks, plus a 3.3V LDO to power the host MCU. According to the NXP product page, the 9V/12V/15V/18V/24V supply tolerance covers automotive load-dump profiles, so the BCM connects directly to the battery rail without extra protection. The integrated watchdog and bus-failure diagnostics lower software overhead and reduce BCM BOM cost versus discrete designs.
Được đề xuất
CAN-LIN Gateway ECU
For CAN-LIN gateway modules the MCZ33905CS3EK provides both physical layers on one die, eliminating a second transceiver IC. With Normal and Sleep modes and CAN or LIN wake-up, the gateway can drop into low-power state and wake on either bus activity, matching automotive quiescent-current targets. The 32-SOIC-EP package and 3.3V regulator output let the gateway drive a small MCU directly, and the integrated watchdog handles independent gateway supervision without external circuitry.
Được đề xuất
HVAC Climate Control Module
HVAC control units typically combine blowers, flaps, and sensors on LIN sub-buses while exchanging climate commands over CAN with the rest of the vehicle; the MCZ33905CS3EK supports both buses and supplies 3.3V to the climate MCU. With -40C to +125C operating range and integrated ESD on CAN/LIN pins, the device handles under-dash thermal and ESD stress without extra TVS parts, simplifying HVAC box design. The exposed-pad SOIC-32 keeps conduction cooling modest at typical HVAC currents, enabling a compact PCB.
Được đề xuất
Seat Control Module
Seat modules use CAN for body controller commands and LIN for switches, motors, and position sensors - exactly the two buses the MCZ33905CS3EK integrates. The integrated 3.3V supply powers the seat MCU and small sensor ICs, reducing module cost. Its automotive temperature grade and battery-range tolerance match seat-mount thermal and electrical stress, while the SBC's watchdog handles the increased supervisory burden of motor-control safety functions.
Được đề xuất
Lighting Control Unit
Lighting ECUs exchange messages with the body controller via CAN and drive lamps and sensors through LIN sub-networks; the MCZ33905CS3EK provides both plus a host 3.3V rail in one IC. According to AiPCBA's datasheet note, normal/sleep operation and bus wake-up let the lighting ECU meet auto-dark current budgets. The integrated ESD and diagnostics reduce field-failure risk for exterior LED driver modules.
Được đề xuất
Sensor Cluster Node (LIN-sub-net)
Distributed sensor clusters for rain-light, battery monitor, or HVAC sensors use LIN as a cost-effective sub-bus while still needing diagnostic and supply functions. The MCZ33905CS3EK's LIN 2.x physical layer, integrated 3.3V supply, and automotive-grade thermal profile allow one device to drop into the cluster, providing both bus connectivity and MCU power. The integrated CAN transceiver is unused in pure-LIN nodes but is harmless because the SBC can be configured to disable its HS-CAN block.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCZ33905CS3EK — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCZ33903DS3EKR2 | MCZ33904BC3EK | MCZ33664EFR2 |
|---|---|---|---|---|
| Package | 32-SOIC-EP | 32-SOIC-EP - same | 32-SOIC-EP - same | 32-SOIC-EP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Function | SBC with HS-CAN + LIN + 3.3V LDO | SBC with dual HS-CAN | SBC with HS-CAN + LIN + 5V LDO | Isolated CAN interface |
| Integrated LDO Output | 3.3 V | 3.3 V | 5.0 V | None (isolated only) |
| CAN Transceivers | 1 (HS) per ISO 11898-2/-5 | 2 (HS) | 1 (HS) | 1 (isolated HS) |
| LIN Transceiver | Yes (single-wire LIN) | No | Yes | No |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
| Lifecycle Status | Last Time Buy per NXP PCN | Check NXP for status | Check NXP for status | Check NXP for status |
| Watchdog | Integrated | Integrated | Integrated | Integrated |
Bảo phân biệt quan trọng
- Single die with HS-CAN + LIN + 3.3V LDO (vsMCZ33903DS3EKR2)
- 3.3V integrated LDO versus 5.0V (vsMCZ33904BC3EK)
- Non-isolated versus isolated CAN interface (vsMCZ33664EFR2)
Ghi chú thiết kế
The exposed thermal pad (pin 32) on the 32-SOIC-EP package is the primary heat path. Solder the EPAD to a top-layer copper land at least equal to the EPAD dimensions with 6+ thermal vias to inner planes. Estimated: with 200 mA of total 3.3V output current at VIN=12V, the linear regulator dissipates approximately (12V - 3.3V) * 0.2A = 1.74W; verify with a thermometer that the EPAD does not exceed 110C in 85C ambient conditions.
Route the CANH and CANL traces as a 100-ohm differential pair from the MCZ33905CS3EK CAN pins to the bus connector. According to NXP application notes for the SBC family, keep the pair length-matched to within 0.5 mm, avoid split ground beneath the bus traces, and place 100 pF capacitors from each CAN line to ground near the connector for EMC. The LIN trace should be routed as a single ended line away from noisy DC-DC nodes.
The MCZ33905CS3EK is in Discontinuance and Replacement per the NXP product page; do not specify it for new automotive platforms without contacting NXP for the recommended successor part. The VBAT pin must be decoupled with at least 100 nF (high-frequency) plus a 10 uF bulk capacitor close to the pin. Missing this decoupling can cause CAN bus error frames during crank events. Always tie the EPAD to ground with a low-impedance path; floating the EPAD can trigger the internal thermal warning at much lower than rated output current.
Thông tin tuân thủ
Compliance data not available in verified snippets. The part is graded Automotive Temperature (per AiPCBA datasheet listing), suggesting the part is intended for AEC-Q100 environments; for explicit certification status please consult the NXP product page.
