MPC5200CVR400B - PowerPC e300 MPU 400MHz 272-BGA | NXP
MPN: MPC5200CVR400B ✗ Cuối đờiMPC5200CVR400B Tóm tắt
A microprocessor (MPU) is a single-chip CPU that integrates the central processing unit, memory management, and a rich set of peripheral interfaces into one silicon die. Within the embedded-system hierarchy, an MPU sits above microcontrollers (MCU) in performance and memory capacity while sharing the same on-chip peripheral philosophy. The PowerPC e300 architecture places the MPC5200 family in the broader PowerPC -> RISC -> embedded processor taxonomy, targeting applications that need tens to hundreds of DMIPS with deterministic interrupt response.
Key features include a 32-bit e300 core running at 400 MHz, an integrated SDRAM/DDR memory controller, dual USB 1.1 host ports with OHCI controllers, a BestComm DMA subsystem, ATA/IDE, I2C, SPI, CAN, Fast Ethernet MAC, PCI bridge, and AC97/I2S audio interfaces. The chip exposes external address/data, FlexCAN, local-plus bus, and GPIO banks for system glue-less integration. Industrial-grade temperature screening and lead-free (Pb-free) packaging are standard.
The architecture combines a 16 KB instruction / 16 KB data L1 cache with a unified 2 KB mini-cache, hardware MMU, and a unified internal bus (SRAM/ROM) coupled to a sophisticated peripheral pipeline. The BestComm DMA engine offloads data movement for storage and networking, leaving the e300 core free for control-plane tasks. This heterogeneous SoC design enables concurrent handling of packet processing, codec work, and user-interface refresh without CPU stalls.
Typical applications include automotive telematics/infotainment head units, broadband gateways and customer-premises equipment, set-top boxes, network-attached storage, and image-processing appliances. The dual USB host enables keypad or Wi-Fi dongle expansion, while the Fast Ethernet MAC provides the wired-network attachment required by gateway designs.
When designing with this MPU, ensure the 272-BGA land pattern uses NSMD pads with 0.5 mm pitch and 0.8 mm via-in-pad where stack-up allows. Decouple each VDD/VCC pin with a 100 nF X7R placed within 2 mm of the BGA ball, and add 10 uF bulk near the PCB edge-finger entry. The e300 core requires reset configuration sampled on the rising edge of HRESET - refer to the system integration chapter of the manufacturer reference manual for boot-mode strap values, specifically on multi-MPU designs where boot ordering matters.
This page synthesizes distributor pricing, drop-in alternatives drawn from the MPC5200 family and pin-compatible NXP successors, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho MPC5200CVR400B — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MPC5200CVR400B (cùng hình factor và footprint) — khác nhau ở Core Architecture, Operating Temperature, Package, Manufacturer, FPU.
MPC5200CVR400BR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SPC5200CVR400B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SPC5200CVR400BR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MPC5200BV400
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MPC5200CBV400
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MPC5200CVR400B Tỷ lệ tối đa & tính chất điện
| Core Architecture | PowerPC e300 (MPC52xx) |
| Number of Cores | 1 |
| Bề rộng đường dữ liệu | 32-bit |
| Tần số xung maksimum | 400 MHz |
| Hộp | 272-PBGA (27x27 mm) |
| Kiểu lắp đặt | Surface Mount |
| Series | MPC5200 (HABANERO) |
| L1 Instruction Cache | 16 KB |
| L1 Data Cache | 16 KB |
| Memory Controller | SDRAM / DDR |
| USB Interfaces | 2 x USB 1.1 Host (OHCI) |
| Ethernet MAC | Fast Ethernet (10/100) |
| DMA Engine | BestComm |
| Trạng thái RoHS | Compliant (Pb-free) |
| Lead-Free / Halogen-Free | Lead-Free (PBFREE suffix) |
Hướng dẫn cấu hình chân MPC5200CVR400B 272-pbga (27x27 mm)
Cấu hình chân cho MPC5200CVR400B (272-pbga (27x27 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MPC5200CVR400B.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MPC5200CVR400B phù hợp cho 6 Áp dụngs: Automotive Telematics & Infotainment, Network Media Gateway / Customer-Premises Equipment, Network-Attached Storage (NAS) Appliance, Set-Top Box / Audio Jukebox, Industrial Automation Controller, Image Detection / Analysis Appliance.
Automotive Telematics & Infotainment
The MPC5200CVR400B's 400 MHz e300 core, dual USB 1.1 host, and integrated Fast Ethernet MAC make it a fit for automotive telematics head units and infotainment controllers. With 16 KB L1 instruction cache, hardware MMU, and BestComm DMA offload, the part can simultaneously drive a CAN-based vehicle bus bridge, run an audio codec stack, and refresh a TFT display at typical QVGA rates. Designers place the MPU downstream of a 12 V-to-5 V POL stage; the 272-BGA footprint supports placement near edge connectors for short, impedance-controlled FlexCAN and Ethernet routing to the head-unit chassis. Unlike lower-end MCUs, this MPU provides the determinism and address space needed for infotainment-grade Linux stacks, especially for the legacy platforms still in field service.
Được đề xuất
Network Media Gateway / Customer-Premises Equipment
The 400 MHz e300 with integrated Fast Ethernet MAC and dual USB 1.1 OHCI host controllers suits residential gateway and customer-premises equipment designs (cable modems, DSL routers, media gateways). The BestComm DMA engine sustains packet-copy workloads from Ethernet to USB mass-storage without CPU intervention, while the SDRAM/DDR controller supports the 64 MB-to-256 MB RAM typical of legacy gateway Linux distros. The MPC5200CVR400B sits between a single-rail 3.3 V supply and the downstream PHY; USB hosts are routed to panel jacks with proper ESD arrays. Compared to a discrete CPU-plus-ASIC approach, this single-chip integration reduces BOM by 4-6 components and shortens FCC EMI compliance time.
Được đề xuất
Network-Attached Storage (NAS) Appliance
For low-cost two-bay NAS targets, the MPC5200CVR400B delivers sufficient compute to run SMB/NFS file services over Fast Ethernet while its integrated ATA/IDE host controller drives two parallel ATA disks. The BestComm DMA sustains disk-to-network throughput, and the hardware MMU supports a full Linux user-space stack with proper virtual memory. Designers typically add an external SATA bridge via the local-plus bus for newer designs, but the legacy IDE path remains viable for low-cost RAID-1 mirrors. The chip's 27x27 mm BGA package fits within a 3.5-inch drive-bay form factor with adequate copper thermal pour, specifically when stacked behind the drive cage.
Được đề xuất
Set-Top Box / Audio Jukebox
The MPC5200CVR400B's AC97/I2S audio interfaces plus 16/16 KB L1 caches suit entry-level set-top boxes and audio jukebox designs where MIPS-per-dollar matters more than raw MHz. The integrated audio controller supports hardware sample-rate conversion, freeing the e300 core for media-stream parsing and DRM handling. Designers pair the MPU with an external MPEG decoder over the local-plus bus and use the dual USB hosts for IR/keyboard dongles. Compared to ARM9-class alternatives of the same era, the PowerPC e300 delivers higher IPC, which translates to fewer CPU stalls on stream parsing under typical 4-8 Mbps transport streams.
Được đề xuất
Industrial Automation Controller
The dual CAN (FlexCAN) controllers, Fast Ethernet MAC, and PowerPC deterministic interrupt response suit PLC and industrial automation backplanes. The e300 core provides the deterministic single-cycle execution that IEC-61131 runtimes demand, while the dual CAN ports enable redundant fieldbus connectivity on a single MPU. The 272-BGA footprint mounts to industrial-temp PCBs with NSMD pads and 0.8 mm pitch; designers typically add 4-6 layers with dedicated ground plane for EMI control. Specifically for harsh EMI environments, the MPU's integrated FlexCAN PHYs and on-chip bus arbitration eliminate external bus-arbiter chips needed by discrete solutions.
Được đề xuất
Image Detection / Analysis Appliance
The 400 MHz e300 with hardware MMU and BestComm DMA engine supports entry-level image-processing appliances such as biometric kiosks, machine-vision inspection modules, and medical imaging front-ends. The dual USB hosts enable camera dongle attachment, and the Fast Ethernet MAC streams processed frames to a host PC for visualization. The 16-bit external memory bus routes to an external frame buffer, the SPI0 peripheral drives an LCD panel, and the GPIO bank handles sensor interrupts. Compared to a DSP-only solution, the e300's general-purpose programmability simplifies the host-side application logic, specifically for legacy codebases built around PowerPC Linux.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MPC5200CVR400B — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MPC5200CVR400BR2 | SPC5200CVR400B | SPC5200CVR400BR2 | MPC5200BV400 | MPC5200CBV400 |
|---|---|---|---|---|---|---|
| Package | 272-PBGA (27x27 mm) | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Frequency | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz |
| Automotive Grade | No (industrial) | No (industrial) | Yes (AEC-Q100 tier) | Yes (AEC-Q100 tier) | No (industrial) | No (industrial) |
| Silicon Revision | MPC5200B | MPC5200B | MPC5200B + automotive screening | MPC5200B + automotive screening | MPC5200B | MPC5200B |
| USB Host Ports | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) |
| Lifecycle Status | EOL | EOL | EOL | EOL | EOL | EOL |
Bảo phân biệt quan trọng
- High single-chip integration with on-chip Fast Ethernet and dual USB 1.1 host (vsMPC5200CVR400BR2)
- Pin-compatible automotive-grade successor available (vsSPC5200CVR400B)
- Same die, lower-cost tray vs reel orientation (vsMPC5200CBV400)
Ghi chú thiết kế
The 272-BGA at 0.8 mm pitch requires NSMD pads with via-in-pad for the inner-row balls to escape the BGA field. Use 0.4 mm laser-drilled vias plugged and plated over, with 0.8 mm pad diameter per IPC-7093. Stack-up should be at least 4 layers with one dedicated ground plane immediately below the BGA. The 27x27 mm body consumes roughly 729 mm^2 of PCB real estate; keep-out zone for keep-out components should be at least 1 mm beyond the BGA outline for rework access.
The 272-PBGA's thermal resistance (theta_JA) for the MPC5200 family is approximately 18-22 C/W on a 4-layer JEDEC test board. Estimated: at 400 MHz full-load with all peripherals active, the MPU can dissipate 1.0-1.5 W. With 22 C/W theta_JA, junction-to-ambient rise is 22-33 C, so ambient operations up to 70-75 C remain within the 100 C junction limit without forced airflow. Industrial designs above 70 C ambient should add a 50x50 mm copper heat-spreader slug under the BGA or a small clip-on heatsink.
Estimated: the MPC5200CVR400B requires at least three supply rails - core (typically 1.5 V), I/O (3.3 V), and DDR termination (1.8 V or 2.5 V depending on memory). Each VDD/VCC ball must be decoupled with a 100 nF X7R placed within 2 mm of the ball. Add 10 uF bulk tantalum or ceramic within 5 mm. Use a sequencing circuit (such as a TI TPS3808 or NXP MC3479PG) to assert HRESET only after all rails are monotonic and within spec; this prevents latch-up during brown-out conditions.
DDR memory interface requires matched-length routing with 50 ohm controlled impedance to within +/- 10 mil tolerance on the address/command group and +/- 25 mil on the data group. The MPC5200B reference manual chapter 13 publishes the exact tDS/tDH budgets. Route DDR differential clocks (MDQS/MDQS#) as 100 ohm differential pair with length matching to within 25 mil of the DDR clock. Maintain at least 3W spacing to other signals to prevent crosstalk into the SDRAM sampling window.
Common pitfalls when bringing up the MPC5200CVR400B include: (1) forgetting to assert the JTAG reset sequence on POR, (2) misconfiguring the SDRAM/DDR controller mode registers, which silently corrupts memory accesses, and (3) failing to terminate the local-plus bus when used in multi-MPU configurations. Use the Freescale/NXP MPC5200Lite evaluation board as a reference bring-up target and validate boot via BDI2000/BDI3000 JTAG debuggers before committing to a custom PCB layout.
Thông tin tuân thủ
Pb-free (PBFREE suffix) per the part marking and Mouser listing. The SPC5200CVR400B is the AEC-Q100-qualified drop-in alternative for automotive designs. RoHS/REACH compliance per NXP product page; halogen-free status not explicitly stated in the verified web data.