MPC5200CVR400B - PowerPC e300 MPU 400MHz 272-BGA | NXP
부품 번호: MPC5200CVR400B ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $39.5 | $39.50 |
| 10 | $35.2 | $352.00 |
| 100 | $31.4 | $3,140.00 |
| 500 | $27.95 | $13,975.00 |
| 1,000 | $24.8 | $24,800.00 |
MPC5200CVR400B 개요
A microprocessor (MPU) is a single-chip CPU that integrates the central processing unit, memory management, and a rich set of peripheral interfaces into one silicon die. Within the embedded-system hierarchy, an MPU sits above microcontrollers (MCU) in performance and memory capacity while sharing the same on-chip peripheral philosophy. The PowerPC e300 architecture places the MPC5200 family in the broader PowerPC -> RISC -> embedded processor taxonomy, targeting applications that need tens to hundreds of DMIPS with deterministic interrupt response.
Key features include a 32-bit e300 core running at 400 MHz, an integrated SDRAM/DDR memory controller, dual USB 1.1 host ports with OHCI controllers, a BestComm DMA subsystem, ATA/IDE, I2C, SPI, CAN, Fast Ethernet MAC, PCI bridge, and AC97/I2S audio interfaces. The chip exposes external address/data, FlexCAN, local-plus bus, and GPIO banks for system glue-less integration. Industrial-grade temperature screening and lead-free (Pb-free) packaging are standard.
The architecture combines a 16 KB instruction / 16 KB data L1 cache with a unified 2 KB mini-cache, hardware MMU, and a unified internal bus (SRAM/ROM) coupled to a sophisticated peripheral pipeline. The BestComm DMA engine offloads data movement for storage and networking, leaving the e300 core free for control-plane tasks. This heterogeneous SoC design enables concurrent handling of packet processing, codec work, and user-interface refresh without CPU stalls.
Typical applications include automotive telematics/infotainment head units, broadband gateways and customer-premises equipment, set-top boxes, network-attached storage, and image-processing appliances. The dual USB host enables keypad or Wi-Fi dongle expansion, while the Fast Ethernet MAC provides the wired-network attachment required by gateway designs.
When designing with this MPU, ensure the 272-BGA land pattern uses NSMD pads with 0.5 mm pitch and 0.8 mm via-in-pad where stack-up allows. Decouple each VDD/VCC pin with a 100 nF X7R placed within 2 mm of the BGA ball, and add 10 uF bulk near the PCB edge-finger entry. The e300 core requires reset configuration sampled on the rising edge of HRESET - refer to the system integration chapter of the manufacturer reference manual for boot-mode strap values, specifically on multi-MPU designs where boot ordering matters.
This page synthesizes distributor pricing, drop-in alternatives drawn from the MPC5200 family and pin-compatible NXP successors, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: MPC5200CVR400B — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MPC5200CVR400B (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Operating Temperature, Package, Manufacturer, FPU.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MPC5200CVR400BR2
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SPC5200CVR400B
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SPC5200CVR400BR2
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MPC5200BV400
✅ 드롭인✓ 재고 있음
$31.2 / 개
데이터시트 보기 →MPC5200CBV400
✅ 드롭인✓ 재고 있음
$40.67 / 개
데이터시트 보기 →MPC5200CVR400B 최대 정격 & 전기적 특성
| Core Architecture | PowerPC e300 (MPC52xx) |
| Number of Cores | 1 |
| 데이터 버스 폭 | 32-bit |
| 최대 클록 주파수 | 400 MHz |
| 패키지 | 272-PBGA (27x27 mm) |
| 실장 유형 | Surface Mount |
| Series | MPC5200 (HABANERO) |
| L1 Instruction Cache | 16 KB |
| L1 Data Cache | 16 KB |
| Memory Controller | SDRAM / DDR |
| USB Interfaces | 2 x USB 1.1 Host (OHCI) |
| Ethernet MAC | Fast Ethernet (10/100) |
| DMA Engine | BestComm |
| RoHS 상태 | Compliant (Pb-free) |
| Lead-Free / Halogen-Free | Lead-Free (PBFREE suffix) |
MPC5200CVR400B 272-pbga (27x27 mm) 핀 구성 가이드
MPC5200CVR400B(272-pbga (27x27 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MPC5200CVR400B.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MPC5200CVR400B 적합 용도: 6 애플리케이션s: Automotive Telematics & Infotainment, Network Media Gateway / Customer-Premises Equipment, Network-Attached Storage (NAS) Appliance, Set-Top Box / Audio Jukebox, Industrial Automation Controller, Image Detection / Analysis Appliance.
Automotive Telematics & Infotainment
The MPC5200CVR400B's 400 MHz e300 core, dual USB 1.1 host, and integrated Fast Ethernet MAC make it a fit for automotive telematics head units and infotainment controllers. With 16 KB L1 instruction cache, hardware MMU, and BestComm DMA offload, the part can simultaneously drive a CAN-based vehicle bus bridge, run an audio codec stack, and refresh a TFT display at typical QVGA rates. Designers place the MPU downstream of a 12 V-to-5 V POL stage; the 272-BGA footprint supports placement near edge connectors for short, impedance-controlled FlexCAN and Ethernet routing to the head-unit chassis. Unlike lower-end MCUs, this MPU provides the determinism and address space needed for infotainment-grade Linux stacks, especially for the legacy platforms still in field service.
추천
Network Media Gateway / Customer-Premises Equipment
The 400 MHz e300 with integrated Fast Ethernet MAC and dual USB 1.1 OHCI host controllers suits residential gateway and customer-premises equipment designs (cable modems, DSL routers, media gateways). The BestComm DMA engine sustains packet-copy workloads from Ethernet to USB mass-storage without CPU intervention, while the SDRAM/DDR controller supports the 64 MB-to-256 MB RAM typical of legacy gateway Linux distros. The MPC5200CVR400B sits between a single-rail 3.3 V supply and the downstream PHY; USB hosts are routed to panel jacks with proper ESD arrays. Compared to a discrete CPU-plus-ASIC approach, this single-chip integration reduces BOM by 4-6 components and shortens FCC EMI compliance time.
추천
Network-Attached Storage (NAS) Appliance
For low-cost two-bay NAS targets, the MPC5200CVR400B delivers sufficient compute to run SMB/NFS file services over Fast Ethernet while its integrated ATA/IDE host controller drives two parallel ATA disks. The BestComm DMA sustains disk-to-network throughput, and the hardware MMU supports a full Linux user-space stack with proper virtual memory. Designers typically add an external SATA bridge via the local-plus bus for newer designs, but the legacy IDE path remains viable for low-cost RAID-1 mirrors. The chip's 27x27 mm BGA package fits within a 3.5-inch drive-bay form factor with adequate copper thermal pour, specifically when stacked behind the drive cage.
추천
Set-Top Box / Audio Jukebox
The MPC5200CVR400B's AC97/I2S audio interfaces plus 16/16 KB L1 caches suit entry-level set-top boxes and audio jukebox designs where MIPS-per-dollar matters more than raw MHz. The integrated audio controller supports hardware sample-rate conversion, freeing the e300 core for media-stream parsing and DRM handling. Designers pair the MPU with an external MPEG decoder over the local-plus bus and use the dual USB hosts for IR/keyboard dongles. Compared to ARM9-class alternatives of the same era, the PowerPC e300 delivers higher IPC, which translates to fewer CPU stalls on stream parsing under typical 4-8 Mbps transport streams.
추천
Industrial Automation Controller
The dual CAN (FlexCAN) controllers, Fast Ethernet MAC, and PowerPC deterministic interrupt response suit PLC and industrial automation backplanes. The e300 core provides the deterministic single-cycle execution that IEC-61131 runtimes demand, while the dual CAN ports enable redundant fieldbus connectivity on a single MPU. The 272-BGA footprint mounts to industrial-temp PCBs with NSMD pads and 0.8 mm pitch; designers typically add 4-6 layers with dedicated ground plane for EMI control. Specifically for harsh EMI environments, the MPU's integrated FlexCAN PHYs and on-chip bus arbitration eliminate external bus-arbiter chips needed by discrete solutions.
추천
Image Detection / Analysis Appliance
The 400 MHz e300 with hardware MMU and BestComm DMA engine supports entry-level image-processing appliances such as biometric kiosks, machine-vision inspection modules, and medical imaging front-ends. The dual USB hosts enable camera dongle attachment, and the Fast Ethernet MAC streams processed frames to a host PC for visualization. The 16-bit external memory bus routes to an external frame buffer, the SPI0 peripheral drives an LCD panel, and the GPIO bank handles sensor interrupts. Compared to a DSP-only solution, the e300's general-purpose programmability simplifies the host-side application logic, specifically for legacy codebases built around PowerPC Linux.
추천
추천 제품 요약
엔지니어링 참조 데이터: MPC5200CVR400B — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MPC5200CVR400BR2 | SPC5200CVR400B | SPC5200CVR400BR2 | MPC5200BV400 | MPC5200CBV400 |
|---|---|---|---|---|---|---|
| Package | 272-PBGA (27x27 mm) | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same | 272-PBGA (27x27 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Frequency | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz |
| Automotive Grade | No (industrial) | No (industrial) | Yes (AEC-Q100 tier) | Yes (AEC-Q100 tier) | No (industrial) | No (industrial) |
| Silicon Revision | MPC5200B | MPC5200B | MPC5200B + automotive screening | MPC5200B + automotive screening | MPC5200B | MPC5200B |
| USB Host Ports | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) | 2 x USB 1.1 (OHCI) |
| Lifecycle Status | EOL | EOL | EOL | EOL | EOL | EOL |
주요 차별점
- High single-chip integration with on-chip Fast Ethernet and dual USB 1.1 host (vs MPC5200CVR400BR2)
- Pin-compatible automotive-grade successor available (vs SPC5200CVR400B)
- Same die, lower-cost tray vs reel orientation (vs MPC5200CBV400)
설계 노트
The 272-BGA at 0.8 mm pitch requires NSMD pads with via-in-pad for the inner-row balls to escape the BGA field. Use 0.4 mm laser-drilled vias plugged and plated over, with 0.8 mm pad diameter per IPC-7093. Stack-up should be at least 4 layers with one dedicated ground plane immediately below the BGA. The 27x27 mm body consumes roughly 729 mm^2 of PCB real estate; keep-out zone for keep-out components should be at least 1 mm beyond the BGA outline for rework access.
The 272-PBGA's thermal resistance (theta_JA) for the MPC5200 family is approximately 18-22 C/W on a 4-layer JEDEC test board. Estimated: at 400 MHz full-load with all peripherals active, the MPU can dissipate 1.0-1.5 W. With 22 C/W theta_JA, junction-to-ambient rise is 22-33 C, so ambient operations up to 70-75 C remain within the 100 C junction limit without forced airflow. Industrial designs above 70 C ambient should add a 50x50 mm copper heat-spreader slug under the BGA or a small clip-on heatsink.
Estimated: the MPC5200CVR400B requires at least three supply rails - core (typically 1.5 V), I/O (3.3 V), and DDR termination (1.8 V or 2.5 V depending on memory). Each VDD/VCC ball must be decoupled with a 100 nF X7R placed within 2 mm of the ball. Add 10 uF bulk tantalum or ceramic within 5 mm. Use a sequencing circuit (such as a TI TPS3808 or NXP MC3479PG) to assert HRESET only after all rails are monotonic and within spec; this prevents latch-up during brown-out conditions.
DDR memory interface requires matched-length routing with 50 ohm controlled impedance to within +/- 10 mil tolerance on the address/command group and +/- 25 mil on the data group. The MPC5200B reference manual chapter 13 publishes the exact tDS/tDH budgets. Route DDR differential clocks (MDQS/MDQS#) as 100 ohm differential pair with length matching to within 25 mil of the DDR clock. Maintain at least 3W spacing to other signals to prevent crosstalk into the SDRAM sampling window.
Common pitfalls when bringing up the MPC5200CVR400B include: (1) forgetting to assert the JTAG reset sequence on POR, (2) misconfiguring the SDRAM/DDR controller mode registers, which silently corrupts memory accesses, and (3) failing to terminate the local-plus bus when used in multi-MPU configurations. Use the Freescale/NXP MPC5200Lite evaluation board as a reference bring-up target and validate boot via BDI2000/BDI3000 JTAG debuggers before committing to a custom PCB layout.
규정 준수 정보
Pb-free (PBFREE suffix) per the part marking and Mouser listing. The SPC5200CVR400B is the AEC-Q100-qualified drop-in alternative for automotive designs. RoHS/REACH compliance per NXP product page; halogen-free status not explicitly stated in the verified web data.