MSP430F1611IPM - 8MHz 16-bit Mixed-Signal MCU | Texas Instruments
MPN: MSP430F1611IPM ✓ Hoạt độngMSP430F1611IPM Tóm tắt
A mixed-signal microcontroller combines a digital processor with analog conversion and interface functions on one device. The MSP430 belongs to the microcontroller and embedded-processor hierarchy rather than a general-purpose processor class. Its 16-bit RISC core uses 16-bit registers and constant generators, while integrated analog peripherals reduce the need for external converters and interface components in compact industrial and instrumentation designs.
Core features include 8 MHz maximum clock speed, 48 KB Flash for firmware, 10 KB SRAM for working data, and 22 I/O ports. The analog subsystem includes a 12-bit ADC, two 12-bit DAC channels, and a comparator. Peripheral integration covers DMA, I2C, SPI, and UART, enabling the MCU to connect sensors, displays, memories, converters, and host processors. I2C support includes standard mode up to 100 kbps and fast mode up to 400 kbps.
Power efficiency is a defining MSP430 characteristic. The device consumes 330 µA in active mode at 1 MHz and 2.2 V, draws 1.1 µA in standby mode, and reaches 0.2 µA in off mode with RAM retention. It also provides five power-saving modes and wakes from standby in less than 6 µs. These figures make deterministic, battery-influenced operation practical when the design alternates between measurement activity and long low-power intervals.
Typical applications include industrial sensor acquisition, low-power instrumentation, portable measurement equipment, embedded data loggers, and compact control systems with analog outputs. The ADC supports analog measurement, while the dual DAC supports control signals, test excitation, or output-voltage setpoints. UART, SPI, I2C, and DMA provide flexible paths for external sensors, storage devices, and communication links.
PCB design should preserve a quiet analog supply path, place decoupling capacitors close to the supply pins, and route analog inputs away from high-current switching nodes. Verify the complete pin description in the manufacturer datasheet before assigning board functions. The 64-LQFP footprint also requires adequate solder-mask and thermal relief around the perimeter pads.
Bộ thay thế dễ dàng lắp đặt cho MSP430F1611IPM — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MSP430F1611IPM (cùng hình factor và footprint) — khác nhau ở Flash Memory, Package, Supply Voltage Range, ADC Resolution, Comparator.
MSP430F1613IPM
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MSP430F1491IPMG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MSP430F1611IPM Tỷ lệ tối đa & tính chất điện
| Product Type | 16-bit mixed-signal microcontroller (MCU) |
| CPU Architecture | MSP430 16-bit RISC |
| Maximum Clock Speed | 8 MHz |
| Flash Memory | 48 KB |
| SRAM | 10 KB |
| ADC Resolution | 12 bits |
| DAC Configuration | Dual 12-bit DAC |
| Comparator | Integrated |
| DMA | Integrated |
| Serial Interfaces | I2C, SPI, UART |
| I/O Ports | 22 ports |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Active Current | 330 µA at 1 MHz and 2.2 V |
| Standby Current | 1.1 µA |
| Off Current with RAM Retention | 0.2 µA |
| Power-Saving Modes | 5 modes |
| Standby Wake-Up Time | Less than 6 µs |
| I2C Maximum Data Rate | 400 kbps in fast mode |
| Hộp | 64-pin LQFP (PM), 10 mm x 10 mm |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân MSP430F1611IPM 64-pin lqfp (pm), 10 mm x 10 mm
Cấu hình chân cho MSP430F1611IPM (64-pin lqfp (pm), 10 mm x 10 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MSP430F1611IPM.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MSP430F1611IPM phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Low-Power Data Logger, Portable Measurement Instrument, Analog Control and Signal Generation, Communication Gateway, Battery-Powered IoT Node.
Industrial Sensor Acquisition
The MSP430F1611IPM suits industrial sensor modules that require local 12-bit conversion, low standby consumption, and flexible communications. Its 48 KB Flash can hold acquisition control, filtering, diagnostics, and calibration routines, while 10 KB SRAM supports working buffers and sensor fusion. The 330 µA active current at 1 MHz and 2.2 V supports repeated measurements, while the less-than-6 µs standby wake-up allows the controller to remain responsive between polls. Use I2C for compatible sensors, SPI for higher-rate converters, and UART for reporting results to a host controller.
Được đề xuất
Low-Power Data Logger
The MSP430F1611IPM is appropriate for periodic data logging because it combines 48 KB Flash with a standby current of 1.1 µA and an off-mode current of 0.2 µA with RAM retention. The MCU can wake, measure through the 12-bit ADC, store information in Flash, and return to a low-power state without frequent processor activity. Its five power-saving modes help separate active acquisition from idle intervals, and the integrated comparator can detect thresholds without continuous software polling. For long deployments, choose a suitable nonvolatile storage strategy and confirm write endurance for the expected logging cycle.
Được đề xuất
Portable Measurement Instrument
The MSP430F1611IPM fits portable measurement equipment that combines analog input conditioning with digital computation and limited power availability. Its 8 MHz 16-bit RISC core can process measurement results, the 12-bit ADC acquires the primary analog channel, and the dual 12-bit DAC can generate reference or control voltages. The 1.8 V minimum operating voltage supports low-voltage product architectures, while standby and RAM-retention modes preserve state between interactions. UART or USB-interface circuitry can expose results to a host, but the board must include the required level conversion and protection for external connections.
Được đề xuất
Analog Control and Signal Generation
The MSP430F1611IPM is well suited to closed-loop control tasks that require measured inputs and programmable outputs on one microcontroller. The 12-bit ADC provides the feedback path, the dual 12-bit DAC channels provide two independently controlled analog outputs, and the comparator can provide fast threshold information. Firmware running on the 16-bit RISC core can implement filtering, proportional-integral-derivative control, limit detection, and fault handling. I2C and SPI expand the design with external sensors or converters, while DMA can transfer peripheral data with less CPU intervention. Validate loop timing and output settling against the target system dynamics.
Được đề xuất
Communication Gateway
The MSP430F1611IPM can serve as a compact gateway between local sensors and a higher-level controller because it combines I2C, SPI, UART, and DMA in a low-power package. I2C supports standard operation up to 100 kbps and fast operation up to 400 kbps, while SPI accommodates faster peripherals and UART provides a straightforward host interface. The 48 KB Flash is sufficient for protocol handling and buffering logic, and 10 KB SRAM supports message queues and packet assembly. Use DMA for predictable peripheral transfers, define protocol timeouts, and ensure the chosen interface voltage levels match the external devices.
Được đề xuất
Battery-Powered IoT Node
The MSP430F1611IPM can serve as the control hub in a battery-powered IoT node that combines sensing, local logic, and low-rate communications. The 16-bit processor provides enough arithmetic capacity for preprocessing, while the 12-bit ADC supports sensor digitization and the dual DAC can drive low-power analog interfaces. Standby current of 1.1 µA and wake-up in less than 6 µs help reduce the time the node spends awake, although the complete energy budget also depends on sensors and radios. Use UART or SPI for attached modules and activate the radio only after local measurements are ready.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MSP430F1611IPM — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MSP430F1613IPM | MSP430F1491IPMG4 |
|---|---|---|---|
| Package | 64-pin LQFP (PM), 10 mm x 10 mm | 64-pin LQFP (PM), 10 mm x 10 mm | 64-pin LQFP (PM), 10 mm x 10 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | 16-bit mixed-signal microcontroller | 16-bit mixed-signal microcontroller | 16-bit mixed-signal microcontroller |
| CPU Architecture | MSP430 16-bit RISC | MSP430 16-bit RISC | MSP430 16-bit RISC |
| Serial Interfaces | I2C, SPI, UART | I2C, SPI, UART | I2C, SPI, UART |
Bảo phân biệt quan trọng
- Exact 48 KB Flash and 10 KB SRAM configuration (vsMSP430F1491IPMG4)
- Documented dual 12-bit DAC integration (vsMSP430F1491IPMG4)
- Low-power mixed-signal integration (vsMSP430F1613IPM)
Ghi chú thiết kế
Place the required supply bypass capacitors adjacent to the MSP430F1611IPM power pins and connect them with short, low-inductance traces. Separate analog and digital return paths as far as practical, especially around ADC and DAC circuits. Route analog inputs away from UART, switching-supply, and high-current outputs to reduce coupling into the 12-bit conversion results.
Do not treat a shared package name as proof of complete electrical interchangeability. Before replacing the MSP430F1611IPM with MSP430F1613IPM or MSP430F1491IPMG4, compare every assigned pin, supply requirement, clock configuration, memory requirement, ADC input, DAC output, DMA channel, and interrupt vector. Confirm that the replacement's software driver and development project support the selected device.
Design the power tree around the 1.8 V to 3.6 V operating range and include enough source current for the processor, analog circuitry, external sensors, and communication interfaces. The 330 µA figure applies to active operation at 1 MHz and 2.2 V and does not include external loads. Use regulator dropout margin, transient response, and startup sequencing appropriate for the complete system.
Keep the 64-pin LQFP footprint within the manufacturer's recommended land pattern and verify pin-one orientation against the package drawing. A 10 mm by 10 mm body requires adequate routing channels for power, ground, analog signals, and serial interfaces. Use vias sparingly beneath fine-pitch devices where process capability is uncertain, and follow the current assembly and land-pattern guidance for the production facility.
Treat analog reference and DAC outputs as sensitive signal paths: use short traces, solid ground references, and separate return paths from digital switching activity. If the ADC samples a high-impedance source, provide suitable settling time and acquisition support according to the manufacturer's guidance. Calibrate offset and gain at the final operating voltage because regulator and reference tolerances can shift the measurement scale.
Thông tin tuân thủ
The manufacturer lists the MSP430F1611 as an active mixed-signal microcontroller. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status require confirmation in the current product compliance documentation.
