Texas Instruments

MSP430F2232IDA - 16-Bit 16MHz Ultra-Low-Power MCU | Texas Instruments

MPN: MSP430F2232IDA ✓ Hoạt động
1.8 V to 3.6 V Vdss 270 µA at 1 MHz and 2.2 V Id 38-pin TSSOP Package 16 MHz Speed 8 KB Memory
MOQ: 1 |

MSP430F2232IDA Tóm tắt

Texas Instruments MSP430F2232IDA is a 16-bit mixed-signal microcontroller built around the MSP430 CPU16 architecture, operating at up to 16 MHz with 8 KB of flash memory and 512 B of SRAM in a 38-pin TSSOP package. It operates from 1.8 V to 3.6 V and integrates UART, SPI, I2C, timers, and mixed-signal peripherals for low-power embedded measurement and control designs.

A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The MSP430 belongs to the embedded microcontroller hierarchy and is optimized for portable measurement systems where energy efficiency and fast wake-up are more important than maximum processor throughput. Its 16-bit RISC CPU, 16-bit registers, constant generators, and 125 ns instruction-cycle capability support compact control code across sensor, communications, and industrial applications.

The MSP430F2232IDA provides ultra-low-power operation through active, standby, and off modes. At 1 MHz and 2.2 V, active-mode current is 270 µA, standby current is 0.7 µA, and off-mode current with RAM retention is 0.1 µA. The device can wake from standby in less than 1 µs, making it suitable for duty-cycled instruments that must respond quickly while conserving battery energy.

Its integrated communication resources include UART, SPI, and I2C interfaces. These allow the MCU to connect local sensors, transceivers, displays, and data-acquisition hardware without requiring separate serial-interface controllers. A timer subsystem supports periodic timing and event handling, while the mixed-signal feature set enables compact instrumentation designs in which analog measurements and digital control share the same device.

Typical applications include portable environmental monitors, industrial sensor nodes, low-power data loggers, building-automation endpoints, and compact measurement instruments. The 1.8 V minimum supply voltage also makes it relevant to energy-harvesting and coin-cell powered systems when the external load and sensor circuitry are designed for the same voltage range.

The principal design consideration is maintaining a complete low-power design rather than treating the MCU alone as an energy-saving component. Select peripheral clocks, sleep durations, pull-up values, and analog front-end biasing to match the measurement workload. Use the manufacturer pin-description table and mixed-signal peripheral guidance when assigning the 38 TSSOP pins and planning decoupling.

This product overview combines the exact orderable MPN, manufacturer feature data, package information, interface capabilities, and practical selection guidance. It also identifies the limits of drop-in sourcing by distinguishing electrically close family options from a verified cross-manufacturer replacement, helping engineers make PCB-level decisions with greater confidence.

Bộ thay thế dễ dàng lắp đặt cho MSP430F2232IDA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

MSP430F2232TDA

✅ Drop-In
📦 38-TSSOP
Same MSP430F2232 family and 38-TSSOP package; orderable grade or qualification code differs, so the exact suffix must be checked against the TI ordering table

📋 Tham chiếu thay thế (không có trong danh mục)

MSP430F2232TDAQ1

✅ Drop-In
📦 38-TSSOP
Same 38-TSSOP footprint and MSP430F2232 function; Q1 indicates an automotive qualification path, creating a qualification difference from the target

📋 Tham chiếu thay thế (không có trong danh mục)

MSP430F2232IDA Tỷ lệ tối đa & tính chất điện

Product Type 16-bit mixed-signal microcontroller
CPU Architecture MSP430 CPU16 16-bit RISC
Tần số xung maksimum 16 MHz
Instruction Cycle Time 125 ns
Flash Memory 8 KB
Flash Organization 8K x 8 plus 256 B
SRAM 512 B
Supply Voltage Range 1.8 V to 3.6 V
Active Current 270 µA at 1 MHz and 2.2 V
Standby Current 0.7 µA
Off Current With RAM Retention 0.1 µA
Standby Wake-Up Time Less than 1 µs
Serial Interfaces UART, SPI, and I2C
Timer Support On-chip timer
Power-Saving Modes Five low-power modes
Hộp 38-pin TSSOP
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân MSP430F2232IDA 38-pin tssop

Cấu hình chân cho MSP430F2232IDA (38-pin tssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 38-pin tssop cho MSP430F2232IDA

Không có dữ liệu chân cụ thể sẵn có cho MSP430F2232IDA.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MSP430F2232IDA phù hợp cho 6 Áp dụngs: Portable Environmental Sensor Node, Industrial Sensor and Condition Monitoring, Low-Power Data Logger, Battery-Powered Metering Instrument, Smart Building Sensor Endpoint, Compact Automation Controller.

🧩

Portable Environmental Sensor Node

The MSP430F2232IDA fits portable environmental monitoring because it combines a 16 MHz CPU16 core with low standby and off-mode current ratings of 0.7 µA and 0.1 µA, respectively. A battery-powered node can wake from standby in less than 1 µs, sample an environmental sensor, transmit the result through UART, SPI, or I2C, and return to sleep. The 1.8 V to 3.6 V operating range supports compact low-voltage designs, while 8 KB flash and 512 B SRAM support short control loops and compact data buffering. Board-level energy consumption will depend on the sensor, radio, regulator efficiency, and sampling interval.

🏭

Industrial Sensor and Condition Monitoring

For industrial condition monitoring, the MSP430F2232IDA provides a 16-bit CPU, timer resources, and three integrated serial interfaces within a 38-pin TSSOP package. It can coordinate pressure, temperature, vibration, or digital sensors and retain local operating state through 512 B of SRAM. The 125 ns instruction-cycle time supports responsive periodic sampling and control, while the 1.8 V to 3.6 V supply range allows integration with compatible low-voltage sensor systems. Industrial designs should still include transient protection, connector isolation, and suitable power regulation at the board level.

📟

Low-Power Data Logger

The MSP430F2232IDA is suited to a low-power data logger that spends most of its operating cycle between measurements. Its 0.7 µA standby current and less-than-1 µs wake-up time permit rapid duty-cycled operation, while the 16 MHz CPU can process readings before transferring stored information through UART or SPI. Eight kilobytes of flash provides room for firmware and configuration data, and 512 B of SRAM supports temporary sample handling. For longer records, an external nonvolatile memory can be added through SPI or I2C; write endurance and data-retention requirements should be included in the system design.

🔧

Battery-Powered Metering Instrument

A compact battery-powered metering instrument benefits from the MSP430F2232IDA's 16-bit RISC architecture, mixed-signal positioning, and low-power operating modes. The microcontroller can operate local control logic at 16 MHz when calculation speed is needed and then reduce activity between samples. UART provides a convenient path to a local display or host, while SPI and I2C support external converters, sensors, and memory. The 38-pin TSSOP package supports compact boards, although designers should follow the manufacturer's land pattern and decoupling guidance. A low-noise regulator and carefully selected analog components remain essential for accurate measurements.

🏠

Smart Building Sensor Endpoint

The MSP430F2232IDA can serve as a smart-building endpoint for occupancy, temperature, or equipment-state monitoring. Its integrated UART, SPI, and I2C interfaces allow connection to environmental sensors and building-network hardware while the 16-bit CPU handles local thresholds and debounce logic. Low standby and off currents are valuable in endpoints expected to operate for long periods between events. The 1.8 V minimum operating voltage also permits use with compatible low-voltage power systems. Installation-specific surge, wiring, grounding, and enclosure requirements should be addressed separately because they are outside the MCU package itself.

⚙️

Compact Automation Controller

The MSP430F2232IDA can act as a compact controller for low-voltage automation subsystems that need deterministic local logic and multiple serial peripherals. Its 16 MHz CPU16 core and 125 ns instruction-cycle capability provide useful throughput for sequencing actuators and processing sensor status, while the timer supports periodic control tasks. The integrated UART, SPI, and I2C interfaces reduce the need for additional protocol-conversion devices. Because the MCU operates only from 1.8 V to 3.6 V, higher-power loads require suitable drivers and regulation. Validate timing under worst-case operating conditions and preserve unused input states to avoid unwanted switching.

What is the MSP430F2232IDA?
The MSP430F2232IDA is a Texas Instruments 16-bit mixed-signal microcontroller with a 16 MHz MSP430 CPU16 core, 8 KB of flash memory, 512 B of SRAM, and a 38-pin TSSOP package. According to the Texas Instruments MSP430F2232 product page, it combines UART, SPI, I2C, and timer resources for low-power measurement and control applications.
What are the key specifications of MSP430F2232IDA that engineers should know?
The MSP430F2232IDA combines a 16 MHz MSP430 CPU16 core, 8 KB flash, 512 B SRAM, a 1.8 V to 3.6 V supply range, and UART/SPI/I2C peripherals in a 38-pin TSSOP. Texas Instruments also identifies 270 µA active current at 1 MHz and 2.2 V, 0.7 µA standby current, 0.1 µA off current with RAM retention, and standby wake-up below 1 µs.
What is the operating voltage of MSP430F2232IDA?
The MSP430F2232IDA operates from 1.8 V to 3.6 V. According to the manufacturer feature information, this low supply-voltage range supports compact portable systems and energy-conscious sensor nodes. The associated external circuitry should also use compatible logic levels and analog input ranges to prevent electrical stress outside the device specifications.
Where can I download the MSP430F2232IDA datasheet PDF?
The MSP430F2232IDA datasheet and supporting documents are available through the Texas Instruments MSP430F2232 product page at https://www.ti.com/product/MSP430F2232. Use the manufacturer document links for the authoritative pin descriptions, electrical characteristics, timing information, and mixed-signal peripheral guidance before finalizing the PCB design.
Where can I find the MSP430F2232IDA pinout?
Use the pin-description table in the Texas Instruments MSP430F2232 datasheet to find the authoritative 38-TSSOP pinout. The package information identifies a 38-pin TSSOP, but individual terminal assignments are not shown on this product page. Confirm package drawing, exposed thermal-pad requirements, and every signal name against the current manufacturer datasheet before routing a board.
How much power does the MSP430F2232IDA consume?
The MSP430F2232IDA draws 270 µA in active mode at 1 MHz and 2.2 V, 0.7 µA in standby mode, and 0.1 µA in off mode with RAM retention. According to Texas Instruments, it wakes from standby in less than 1 µs. Actual board consumption can be higher after accounting for sensors, pull resistors, communications, and regulator losses.
What can replace the MSP430F2232IDA?
The closest documented alternatives are the Texas Instruments MSP430F2232TDA and MSP430F2232TDAQ1, but they require careful review of temperature, qualification, and ordering differences before substitution. No verified cross-manufacturer pin-compatible replacement was identified. A replacement is not drop-in merely because it uses a 38-pin TSSOP; confirm the pin table, clock, memory, peripherals, and firmware behavior.
Is MSP430F2232IDA the same as MSP430F2232TDA?
No. The MSP430F2232IDA and MSP430F2232TDA belong to the same MSP430F2232 family and use the same 38-pin TSSOP package family, but their orderable suffixes can encode different device grades or qualification conditions. The exact distinguishing characteristics are not visible in the available product snippets, so review the TI ordering table before treating either part as a drop-in replacement.
MSP430F2232IDA vs MSP430F2232TDA: which is better for an industrial design?
Choose the MSP430F2232IDA for a design that specifically requires the industrial-grade orderable device identified in the manufacturer catalog. Choose the MSP430F2232TDA only after its exact temperature grade, qualification, and ordering parameters have been confirmed against the MSP430F2232 datasheet. Both are based on the same 16 MHz, 8 KB-flash MCU family, but suffix differences prevent an automatic substitution.
When should I choose MSP430F2232IDA over MSP430F2232TDA?
Choose the MSP430F2232IDA when its specified ordering grade, supply range, package, and qualification match the production requirements. Consider MSP430F2232TDA only if the manufacturer ordering table confirms that its temperature or qualification characteristics better satisfy the application. Both provide the same core MSP430F2232 function, so family-level resources can be evaluated before the final orderable suffix is chosen.
Is MSP430F2232IDA suitable for battery-powered sensor nodes?
The MSP430F2232IDA is suitable for battery-powered sensor nodes because its standby current is 0.7 µA, off current with RAM retention is 0.1 µA, and standby wake-up time is less than 1 µs. Actual battery life also depends on sensor current, sampling interval, communication duty cycle, regulator efficiency, and leakage across the complete board.
Which interfaces are integrated into MSP430F2232IDA?
The MSP430F2232IDA integrates UART, SPI, and I2C interfaces together with timer resources. According to the Texas Instruments product page, these peripherals support connected low-power systems without separate serial controllers. Select external pull-ups and connector isolation appropriate to the target bus voltage, and avoid enabling unused peripherals to reduce energy consumption.
Can MSP430F2232IDA replace a generic 16-bit microcontroller in an existing design?
The MSP430F2232IDA can replace a generic microcontroller only if the replacement board preserves its 38-TSSOP footprint, pin assignments, supply voltage, clock strategy, memory map, and required peripherals. Software compatibility is not automatic because the MSP430 instruction set, interrupt system, and peripheral registers are device-specific. Port the firmware and validate timing and mixed-signal behavior before production.
Where to buy MSP430F2232IDA online?
Use the Request a Quote form on this page to request the MSP430F2232IDA, current availability, and lead time. The form allows the exact 38-pin TSSOP orderable MPN and intended grade to be confirmed before an order is placed. The manufacturer and distributor product links listed for this page can also be used to review documentation and ordering details.
What is the price of MSP430F2232IDA?
Current pricing for the MSP430F2232IDA is handled through the Request a Quote form on this page rather than a static price statement. The form can return the applicable unit and quantity-break pricing for the exact MSP430F2232IDA orderable code. It also helps distinguish the target MPN from related family members with different package, temperature, or qualification suffixes.
What is the lead time for MSP430F2232IDA?
Request the current MSP430F2232IDA lead time through the Request a Quote form on this page. Lead time depends on manufacturer inventory, the exact orderable suffix, order quantity, and fulfillment conditions. The manufacturer product page should be used to confirm the part identity and available documentation before committing the device to a production schedule.

Dữ liệu tham khảo kỹ thuật cho MSP430F2232IDA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MSP430F2232IDA when the design requires a 16 MHz MSP430 mixed-signal MCU with 8 KB flash, 512 B SRAM, low-power operation, and integrated UART, SPI, and I2C in a 38-pin TSSOP package. It is particularly appropriate for battery-operated sensor nodes, compact data loggers, and portable measurement instruments. Select MSP430F2232TDA only when its exact temperature and ordering conditions satisfy the project and the manufacturer ordering table confirms interchangeability. Use MSP430F2232TDAQ1 when the automotive Q1 qualification path is required and its grade meets the deployment environment. No verified cross-manufacturer drop-in replacement was found, so changing brands would normally require PCB and firmware adaptation rather than simple component substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này MSP430F2232TDA MSP430F2232TDAQ1
Package 38-TSSOP 38-TSSOP 38-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments
CPU 16-bit MSP430 CPU16 RISC 16-bit MSP430 CPU16 RISC 16-bit MSP430 CPU16 RISC
Maximum Clock Frequency 16 MHz 16 MHz 16 MHz
Flash Memory 8 KB 8 KB 8 KB
SRAM 512 B 512 B 512 B
Supply Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V
Serial Interfaces UART, SPI, and I2C UART, SPI, and I2C UART, SPI, and I2C

Bảo phân biệt quan trọng

  • Exact industrial orderable designation (vsMSP430F2232TDA)
  • Non-automotive family positioning (vsMSP430F2232TDAQ1)
  • Integrated low-power communication peripherals (vsMSP430F2232TDA)

Ghi chú thiết kế

Design the complete board for the MSP430F2232IDA's low-power modes rather than evaluating the 0.7 µA standby rating in isolation. Disable unused peripherals, define clear sleep-entry and wake conditions, and account for sensor leakage, pull resistors, communications activity, and regulator quiescent current. Use the manufacturer power-management guidance to determine whether RAM retention is required during off mode and how wake-up should be initiated.

Follow the manufacturer's 38-TSSOP land pattern and place input and output decoupling capacitors close to their associated supply pins. Because this package is not represented in the selected package-diagram library, use the official Texas Instruments package drawing for pad dimensions, solder-mask clearance, and copper recommendations. Verify the pin table before assigning test points or routing mixed-signal inputs.

Separate analog inputs and their ground paths from switching-node and high-current return paths. Keep sensor traces short, use a continuous ground reference where practical, and place external analog filtering components near the sensing source. For UART, SPI, and I2C, verify logic levels and use appropriate pull resistor values; excessive pull strength can increase active-mode current even when the MCU is otherwise operating efficiently.

Do not substitute a family member solely because its package has the same pin count. Confirm the exact orderable suffix, temperature grade, qualification path, pin assignments, clock implementation, and peripheral mix in the MSP430F2232 ordering information. Re-test boot code, interrupt timing, mixed-signal calibration, and low-power behavior after any substitution; package equivalence alone does not guarantee behavioral equivalence.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Qualified
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The target MPN does not carry the Q1 automotive-ordering designation. Detailed RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the available product information.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MSP430F2232IDA datasheet MSP430F2232IDA specifications MSP430F2232IDA pinout MSP430F2232IDA datasheet pdf Texas Instruments MSP430F2232IDA MSP430F2232IDA equivalent MSP430F2232IDA replacement MSP430F2232IDA cross reference MSP430F2232IDA vs MSP430F2232TDA MSP430F2232IDA footprint MSP430F2232IDA application circuit MSP430F2232IDA price MSP430F2232IDA stock MSP430F2232 16MHz microcontroller MSP430F2232 38-TSSOP

Các bộ phận và thuật ngữ liên quan

Texas Instruments MSP430F2232IDA MSP430F2232TDA MSP430F2232TDAQ1 MSP430F2232 MSP430 MSP430 CPU16 16-bit RISC microcontroller mixed-signal microcontroller embedded processor semiconductor UART SPI I2C timer flash memory SRAM standby mode RAM retention wake-up time 38-TSSOP TSSOP package family surface-mount package low-power measurement
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ