OPA445AP - ±45V High-Voltage FET-Input Op Amp | Texas Instruments
MPN: OPA445AP ✓ Hoạt độngOPA445AP Tóm tắt
An operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs while providing high input impedance and low output impedance. The OPA445AP belongs to the FET-input operational-amplifier family, which is useful when source impedance is high and input bias current must remain low. Its high-voltage capability distinguishes it from conventional low-voltage signal amplifiers and makes it suitable for industrial, audio, instrumentation, and test-and-measurement signal paths.
The verified manufacturer description identifies the OPA445 as a monolithic operational amplifier capable of operation from supplies up to ±45 V and output currents of 15 mA. The verified distributor and datasheet listings identify the OPA445AP as a single amplifier in an 8-pin PDIP package. The device's 2 MHz gain-bandwidth product and 15 V/µs slew rate make it appropriate for moderate-bandwidth amplification, buffering, and signal-conditioning applications rather than high-frequency precision signal chains.
The OPA445AP is useful in high-voltage analog front ends, audio voltage-amplification stages, laboratory instrumentation, industrial control interfaces, and power-supply monitoring circuits. Because it uses a high-voltage architecture, PCB design must preserve adequate creepage and clearance between supply nets and surrounding conductive features. Decoupling capacitors should be placed close to the supply pins, and the input and output routing should avoid long traces that can increase noise pickup.
The most important design trade-off is the balance between its wide supply-voltage range and the operating limits of the surrounding circuit. Supply rails must remain within the manufacturer’s stated operating limits, and the output must not be loaded beyond the verified 15 mA capability. Signal amplitudes, input common-mode range, output swing, stability, and thermal behavior should be checked against the manufacturer datasheet before the part is used as a drop-in substitute for another amplifier.
This page combines the verified OPA445AP package, supply, speed, and sourcing information with application guidance, comparison criteria, and design checks intended to help engineers select and integrate the amplifier correctly.
Bộ thay thế dễ dàng lắp đặt cho OPA445AP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếOPA445AP Tỷ lệ tối đa & tính chất điện
| Product Type | Single operational amplifier |
| Input Type | FET input |
| Maximum Supply Voltage | ±45 V |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 15 V/µs |
| Điện áp tối đa đầu ra | 15 mA |
| Number of Circuits | 1 |
| Amplifier Type | General-purpose operational amplifier |
| Hộp | 8-PDIP |
| Kiểu lắp đặt | Through hole |
Hướng dẫn cấu hình chân OPA445AP 8-pdip
Cấu hình chân cho OPA445AP (8-pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho OPA445AP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
OPA445AP phù hợp cho 6 Áp dụngs: High-Voltage Audio Voltage Amplifier, Industrial Sensor Signal Conditioning, Power-Supply Feedback Monitoring, Laboratory Instrumentation Buffer, Precision Current Measurement Interface, Audio-Critical Buffering.
High-Voltage Audio Voltage Amplifier
The OPA445AP fits high-voltage audio voltage-amplification stages because it supports supplies up to ±45 V, uses a FET input, and provides a 15 V/µs slew rate. It can precede a higher-current power amplifier when the designer needs additional voltage gain or signal shaping. The 2 MHz gain-bandwidth product is sufficient for many audio-band applications, while the 15 mA output-current capability means the load must remain within the device’s rated limits. Confirm output swing, thermal conditions, and stability for the selected closed-loop gain.
Được đề xuất
Industrial Sensor Signal Conditioning
OPA445AP is appropriate for conditioning signals from high-impedance industrial sensors when the signal chain must tolerate elevated supply voltages. Its FET input reduces loading on the source, while the ±45 V architecture provides headroom for larger common-mode signals than conventional low-voltage amplifiers. The 2 MHz bandwidth and 15 V/µs slew rate support general measurement and control functions rather than precision signal-chain timing. Verify the input common-mode range, offset, noise, and stability at the actual operating gain.
Được đề xuất
Power-Supply Feedback Monitoring
The OPA445AP can monitor high-voltage power-supply nodes in laboratory and industrial systems when the feedback divider and protection network are designed for the relevant voltage range. Its ±45 V supply capability allows operation near elevated rails, and the FET input helps limit loading on the monitored divider. The amplifier’s 2 MHz gain-bandwidth product is more than adequate for slow supervisory signals. The key design checks are input common-mode limits, resistor power ratings, output swing, and isolation from switching-node transients.
Được đề xuất
Laboratory Instrumentation Buffer
OPA445AP is suitable for buffer and gain stages in laboratory instrumentation when test signals require a higher supply range than ordinary precision op amps provide. Its FET-input architecture supports high-impedance probes, and the 15 V/µs slew rate preserves useful response for moderate-frequency waveforms. The 2 MHz gain-bandwidth product should be included in the bandwidth budget for the selected closed-loop gain. Designers should also account for input capacitance, output loading, noise, and the need for clean grounding around the through-hole package.
Được đề xuất
Precision Current Measurement Interface
OPA445AP can be used around current-shunt and high-side sensing nodes when the sensing amplifier must tolerate a wide voltage range and the source presents a meaningful common-mode voltage. Its low-bias FET-input characteristic helps preserve measurement integrity with high source impedance, and its ±45 V supply capability supports elevated industrial rails. The 2 MHz bandwidth is suitable for many current-loop monitoring functions, although offset and drift determine accuracy. Confirm the common-mode range and stability for the selected gain and shunt network.
Được đề xuất
Audio-Critical Buffering
OPA445AP is useful for high-impedance audio buffering where conventional low-voltage amplifiers would not provide enough supply or common-mode range. The FET input helps minimize disturbance to the source, while the 2 MHz gain-bandwidth product and 15 V/µs slew rate provide adequate response for many audio paths. Use the device as a voltage buffer or gain stage rather than assuming it can directly drive a speaker. Output swing, load, thermal rise, and stable-noise performance must be evaluated with the intended audio network.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho OPA445AP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Bảo phân biệt quan trọng
- High-voltage signal amplification (vsOPA445AU)
- Through-hole DIP integration (vsOPA445AU)
- Moderate-bandwidth high-voltage performance (vsOPA445AU)
Ghi chú thiết kế
Place supply bypass capacitors close to the OPA445AP supply pins and connect the regulator return directly to the device ground. Keep input and feedback traces short, and route them away from supply and output nets to reduce capacitive pickup. Because the package is through-hole DIP, pay particular attention to lead inductance and the grounding of the supply bypass node.
Treat the ±45 V rails as a high-voltage design even when the signal amplitude is small. Verify absolute maximum limits, provide appropriate board clearance, and confirm that the power-supply design can start and stop without exceeding the amplifier’s limits. Add input protection or attenuation if a transient or fault condition could exceed the specified input range.
Do not select the OPA445AU as a direct replacement for the OPA445AP in an existing 8-pin PDIP footprint; the mounting styles differ. For replacements, compare supply range, common-mode range, output swing, input bias, offset, noise, bandwidth, slew rate, stability, and thermal behavior. Also check whether the substitute remains unity-gain stable under the intended feedback network.
Estimate power dissipation from the actual supply voltage, output voltage, and load current rather than using the nominal rail voltage alone. The dissipated power is approximately the output voltage multiplied by load current for a complementary output stage. Compare the resulting junction-temperature estimate with the package thermal limits and retain PCB copper as a heat spreader.
Thông tin tuân thủ
The verified manufacturer and distributor results identify the device and package but do not provide a compliance declaration in their displayed content.