Texas Instruments

OPA445AP - ±45V High-Voltage FET-Input Op Amp | Texas Instruments

MPN: OPA445AP ✓ सक्रिय
±45 V Vdss 15 mA Id 8-PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

OPA445AP अवलोकन

The Texas Instruments OPA445AP is a single high-voltage FET-input operational amplifier designed for operation from power supplies up to ±45 V, with an output current capability of 15 mA. The device is supplied in an 8-pin through-hole DIP package and is intended for applications requiring high output-voltage capability or large common-mode voltage swings. Its principal verified characteristics are ±45 V maximum supply operation, 2 MHz gain-bandwidth product, and 15 V/µs slew rate.

An operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs while providing high input impedance and low output impedance. The OPA445AP belongs to the FET-input operational-amplifier family, which is useful when source impedance is high and input bias current must remain low. Its high-voltage capability distinguishes it from conventional low-voltage signal amplifiers and makes it suitable for industrial, audio, instrumentation, and test-and-measurement signal paths.

The verified manufacturer description identifies the OPA445 as a monolithic operational amplifier capable of operation from supplies up to ±45 V and output currents of 15 mA. The verified distributor and datasheet listings identify the OPA445AP as a single amplifier in an 8-pin PDIP package. The device's 2 MHz gain-bandwidth product and 15 V/µs slew rate make it appropriate for moderate-bandwidth amplification, buffering, and signal-conditioning applications rather than high-frequency precision signal chains.

The OPA445AP is useful in high-voltage analog front ends, audio voltage-amplification stages, laboratory instrumentation, industrial control interfaces, and power-supply monitoring circuits. Because it uses a high-voltage architecture, PCB design must preserve adequate creepage and clearance between supply nets and surrounding conductive features. Decoupling capacitors should be placed close to the supply pins, and the input and output routing should avoid long traces that can increase noise pickup.

The most important design trade-off is the balance between its wide supply-voltage range and the operating limits of the surrounding circuit. Supply rails must remain within the manufacturer’s stated operating limits, and the output must not be loaded beyond the verified 15 mA capability. Signal amplitudes, input common-mode range, output swing, stability, and thermal behavior should be checked against the manufacturer datasheet before the part is used as a drop-in substitute for another amplifier.

This page combines the verified OPA445AP package, supply, speed, and sourcing information with application guidance, comparison criteria, and design checks intended to help engineers select and integrate the amplifier correctly.

के लिए ड्रॉप-इन विकल्प OPA445AP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।

विकल्प अनुरोध करें

OPA445AP Maximum Ratings और Electrical Characteristics

Product Type Single operational amplifier
Input Type FET input
Maximum Supply Voltage ±45 V
Gain-Bandwidth Product 2 MHz
Slew Rate 15 V/µs
अधिकतम आउटपुट करंट 15 mA
Number of Circuits 1
Amplifier Type General-purpose operational amplifier
पैकेज 8-PDIP
माउंटिंग प्रकार Through hole

OPA445AP 8-pdip पिन कॉन्फ़िगरेशन गाइड

OPA445AP (8-pdip पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

OPA445AP के लिए 8-pdip पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: OPA445AP.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

OPA445AP के लिए उपयुक्त है 6 अनुप्रयोगs: High-Voltage Audio Voltage Amplifier, Industrial Sensor Signal Conditioning, Power-Supply Feedback Monitoring, Laboratory Instrumentation Buffer, Precision Current Measurement Interface, Audio-Critical Buffering.

🎧

High-Voltage Audio Voltage Amplifier

The OPA445AP fits high-voltage audio voltage-amplification stages because it supports supplies up to ±45 V, uses a FET input, and provides a 15 V/µs slew rate. It can precede a higher-current power amplifier when the designer needs additional voltage gain or signal shaping. The 2 MHz gain-bandwidth product is sufficient for many audio-band applications, while the 15 mA output-current capability means the load must remain within the device’s rated limits. Confirm output swing, thermal conditions, and stability for the selected closed-loop gain.

🏭

Industrial Sensor Signal Conditioning

OPA445AP is appropriate for conditioning signals from high-impedance industrial sensors when the signal chain must tolerate elevated supply voltages. Its FET input reduces loading on the source, while the ±45 V architecture provides headroom for larger common-mode signals than conventional low-voltage amplifiers. The 2 MHz bandwidth and 15 V/µs slew rate support general measurement and control functions rather than precision signal-chain timing. Verify the input common-mode range, offset, noise, and stability at the actual operating gain.

⚡

Power-Supply Feedback Monitoring

The OPA445AP can monitor high-voltage power-supply nodes in laboratory and industrial systems when the feedback divider and protection network are designed for the relevant voltage range. Its ±45 V supply capability allows operation near elevated rails, and the FET input helps limit loading on the monitored divider. The amplifier’s 2 MHz gain-bandwidth product is more than adequate for slow supervisory signals. The key design checks are input common-mode limits, resistor power ratings, output swing, and isolation from switching-node transients.

🔧

Laboratory Instrumentation Buffer

OPA445AP is suitable for buffer and gain stages in laboratory instrumentation when test signals require a higher supply range than ordinary precision op amps provide. Its FET-input architecture supports high-impedance probes, and the 15 V/µs slew rate preserves useful response for moderate-frequency waveforms. The 2 MHz gain-bandwidth product should be included in the bandwidth budget for the selected closed-loop gain. Designers should also account for input capacitance, output loading, noise, and the need for clean grounding around the through-hole package.

📊

Precision Current Measurement Interface

OPA445AP can be used around current-shunt and high-side sensing nodes when the sensing amplifier must tolerate a wide voltage range and the source presents a meaningful common-mode voltage. Its low-bias FET-input characteristic helps preserve measurement integrity with high source impedance, and its ±45 V supply capability supports elevated industrial rails. The 2 MHz bandwidth is suitable for many current-loop monitoring functions, although offset and drift determine accuracy. Confirm the common-mode range and stability for the selected gain and shunt network.

🎵

Audio-Critical Buffering

OPA445AP is useful for high-impedance audio buffering where conventional low-voltage amplifiers would not provide enough supply or common-mode range. The FET input helps minimize disturbance to the source, while the 2 MHz gain-bandwidth product and 15 V/µs slew rate provide adequate response for many audio paths. Use the device as a voltage buffer or gain stage rather than assuming it can directly drive a speaker. Output swing, load, thermal rise, and stable-noise performance must be evaluated with the intended audio network.

What is the OPA445AP?
The OPA445AP is a single high-voltage FET-input operational amplifier from Texas Instruments designed for supplies up to ±45 V. It operates as a general-purpose precision signal-conditioning amplifier in an 8-pin PDIP package. According to the Texas Instruments OPA445 datasheet, the monolithic device supports output currents of 15 mA and is useful where high output voltage or large common-mode voltage swings are required.
What is the OPA445AP supply voltage range?
The OPA445AP supports supply operation up to ±45 V, according to the Texas Instruments OPA445 manufacturer datasheet. The exact recommended operating supply range and absolute maximum ratings should be taken from the datasheet tables before design sign-off. The OPA445AP is therefore intended for substantially higher voltage rails than conventional low-voltage operational amplifiers.
What are the key specifications of OPA445AP that engineers should know?
The main OPA445AP specifications are ±45 V maximum supply operation, 2 MHz gain-bandwidth product, 15 V/µs slew rate, 15 mA output-current capability, FET inputs, and an 8-pin PDIP package. These figures define a high-voltage, moderate-bandwidth amplifier for instrumentation, industrial, audio, and test applications. The Texas Instruments manufacturer datasheet is the controlling reference for complete electrical limits.
Where can I download the OPA445AP datasheet PDF?
The official Texas Instruments OPA445 datasheet PDF is available from the manufacturer page linked on this product page. It contains the device description, electrical characteristics, pin configuration, application information, and ordering details for the OPA445AP. Use the manufacturer document rather than an unofficial mirror when determining ratings or pin assignments.
Where can I find the OPA445AP pinout?
The OPA445AP pinout is shown in the pin-configuration section of the Texas Instruments OPA445 datasheet. The part is an 8-pin PDIP package, so the package has eight physical leads in a through-hole dual-inline arrangement. Confirm signal names and supply-pin locations against the datasheet before assigning PCB nets or designing a replacement board.
Is the OPA445AP suitable for audio amplifier applications?
The OPA445AP can be used in audio voltage-amplification and signal-conditioning stages because it combines a ±45 V supply capability with FET inputs and a 15 V/µs slew rate. Its 2 MHz gain-bandwidth product is adequate for many audio-band tasks. Output-current and output-swing limits must be checked for the selected load and output stage.
Is the OPA445AP suitable for industrial instrumentation?
The OPA445AP is suitable for many industrial instrumentation blocks because its high-voltage supply capability can accommodate elevated signal ranges, while the FET input supports high-impedance sources. The 2 MHz gain-bandwidth product and 15 V/µs slew rate are appropriate for general-purpose measurement and control paths. Check common-mode range, noise, offset, and stability at the intended gain.
OPA445AP vs OPA445AU: which package should I choose?
The OPA445AP is supplied in an 8-pin PDIP package, while OPA445AU is identified as a surface-mount alternative in the comparison information. Because the mounting style differs, OPA445AU is not a pin-for-pin drop-in replacement for an existing OPA445AP board. Choose OPA445AP for through-hole designs and OPA445AU only when the PCB footprint is intentionally changed.
What is the best drop-in replacement for OPA445AP?
No verified same-package, pin-compatible drop-in replacement for the OPA445AP is identified in the available cross-reference information. The OPA445AU uses a surface-mount package and therefore cannot directly replace an OPA445AP in an 8-pin PDIP footprint. For a new design, compare the OPA445AP against other 8-pin high-voltage amplifiers using supply range, input stage, bandwidth, slew rate, output swing, and stability.
Can OPA445AU replace OPA445AP on an existing PCB?
The OPA445AU cannot be assumed to replace the OPA445AP on an existing PCB because the OPA445AP is an 8-pin PDIP device and the OPA445AU is a surface-mount device. The change requires a different footprint and layout review. Treat it as a design migration rather than a drop-in substitution.
Where to buy OPA445AP online?
Use the Request a Quote form on this page to request OPA445AP availability, minimum order quantity, and current lead time. The OPA445AP is cataloged as an 8-PDIP Texas Instruments amplifier, and its sourcing status can be confirmed through the quote workflow. Current commercial terms should be taken from that quotation rather than from static web text.
What is the price of OPA445AP?
The current OPA445AP commercial price is obtained through the Request a Quote form on this page. Pricing can vary with quantity, package, and supply conditions, so use the quote response for an actionable figure. The product page does not present a static price as a substitute for a current quotation.
What is the lead time for OPA445AP?
The current OPA445AP lead time and minimum order quantity should be requested through the Request a Quote form on this page. Texas Instruments lists the OPA445AP as an 8-PDIP operational amplifier, but manufacturing availability and order scheduling can change. The quote workflow provides the current answer for the exact MPN and requested quantity.
Is OPA445AP in stock?
Current OPA445AP stock should be confirmed through the Request a Quote form on this page. Stock status is quantity-dependent and can change after the last market update. Submit the required quantity and packaging information to receive a current availability response for the exact OPA445AP MPN.
How should I design the PCB around OPA445AP?
Place input, output, and supply bypass components close to their associated OPA445AP pins, and route high-impedance input traces away from supply and output conductors. Maintain suitable clearance between the ±45 V-capable supply nodes and surrounding copper or board features. The Texas Instruments datasheet should govern pin placement, decoupling, and any application-specific layout requirements.
Does OPA445AP need a heatsink?
The OPA445AP is normally used as a voltage amplifier rather than a high-current power-output stage, and its verified output-current capability is 15 mA. Heat requirements depend on supply voltage, output swing, load current, ambient temperature, and PCB copper. For high dissipation, estimate junction rise using the thermal information in the manufacturer datasheet and preserve adequate copper area.

के लिए इंजीनियरिंग संदर्भ डेटा OPA445AP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the OPA445AP when the circuit requires a high-voltage operational amplifier in an 8-pin through-hole DIP footprint, particularly around audio voltage stages, industrial signal conditioning, laboratory instrumentation, and supply-feedback monitoring. Its verified ±45 V supply capability, 2 MHz gain-bandwidth product, 15 V/µs slew rate, FET input, and 15 mA output-current capability make it appropriate for moderate-bandwidth voltage amplification rather than direct speaker or power-stage drive. Select a surface-mount OPA445-family configuration for a new compact PCB, but do not treat it as a drop-in replacement for the PDIP OPA445AP. For any third-party substitute, verify supply range, common-mode range, output swing, offset, noise, stability, thermal performance, and exact pin assignments. The most important choice is therefore package compatibility first, followed by the complete electrical operating envelope.

मुख्य विशेषताएँ

  • High-voltage signal amplification (बनामOPA445AU)
  • Through-hole DIP integration (बनामOPA445AU)
  • Moderate-bandwidth high-voltage performance (बनामOPA445AU)

डिज़ाइन नोट्स

Place supply bypass capacitors close to the OPA445AP supply pins and connect the regulator return directly to the device ground. Keep input and feedback traces short, and route them away from supply and output nets to reduce capacitive pickup. Because the package is through-hole DIP, pay particular attention to lead inductance and the grounding of the supply bypass node.

Treat the ±45 V rails as a high-voltage design even when the signal amplitude is small. Verify absolute maximum limits, provide appropriate board clearance, and confirm that the power-supply design can start and stop without exceeding the amplifier’s limits. Add input protection or attenuation if a transient or fault condition could exceed the specified input range.

Do not select the OPA445AU as a direct replacement for the OPA445AP in an existing 8-pin PDIP footprint; the mounting styles differ. For replacements, compare supply range, common-mode range, output swing, input bias, offset, noise, bandwidth, slew rate, stability, and thermal behavior. Also check whether the substitute remains unity-gain stable under the intended feedback network.

Estimate power dissipation from the actual supply voltage, output voltage, and load current rather than using the nominal rail voltage alone. The dissipated power is approximately the output voltage multiplied by load current for a complementary output stage. Compare the resulting junction-temperature estimate with the package thermal limits and retain PCB copper as a heat spreader.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The verified manufacturer and distributor results identify the device and package but do not provide a compliance declaration in their displayed content.

डेटा सत्यापन तिथि: 2026-11-19 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

opa445ap datasheet OPA445AP Texas Instruments OPA445AP pinout OPA445AP datasheet pdf OPA445AP ±45V op amp OPA445AP 2MHz bandwidth OPA445AP 8-PDIP amplifier OPA445AP drop-in replacement OPA445AP price OPA445AP stock and lead time OPA445AP vs OPA445AU OPA445AP application circuit

संबंधित कंपोनेंट्स और शब्द

Texas Instruments OPA445AP OPA445 OPA445AU OPA541AP Operational amplifier FET-input operational amplifier Analog signal conditioner High-voltage amplifier Monolithic amplifier Single amplifier ±45 V power supply 2 MHz gain-bandwidth product 15 V/µs slew rate 15 mA output current 8-PDIP package Through-hole mounting Common-mode voltage Output voltage swing Input bias current Input offset voltage Industrial instrumentation Audio voltage amplification Power-supply feedback monitoring
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें