OPA860ID - 370MHz Wide-Bandwidth OTA & Buffer | Texas Instruments
MPN: OPA860ID ✓ Hoạt độngOPA860ID Tóm tắt
An operational transconductance amplifier is an amplifier whose output current is controlled by an input voltage. In signal-path terms, an OTA belongs to the operational-amplifier family, but it transfers current rather than presenting a conventional voltage output. The OPA860ID also contains a wide-band voltage buffer that can follow the OTA output, giving designers both transconductance and buffered-voltage operating modes in one package.
The principal feature of the OPA860ID is its 370 MHz small-signal bandwidth. This bandwidth supports high-speed video, RF, and intermediate-frequency signal chains where the transconductance stage must amplify small control or error signals without excessive delay. The OTA can also be used as a current-output stage, while the internal buffer supplies a low-impedance voltage output when the system requires conventional signal routing.
Because the device combines an OTA and a buffer, the circuit designer can select the more appropriate output stage for a given application. The OTA section operates as a voltage-controlled current source, while the buffer section provides a conventional voltage output. This versatility is useful in video and RF systems that evaluate gain, impedance, and loading behavior during prototype development.
Typical uses include high-performance video processing, RF and IF signal conditioning, current-feedback and transconductance-based filter stages, laboratory instrumentation, and wideband analog signal chains. The single +5 V supply arrangement simplifies system design compared with dual-supply analog circuits, although output headroom must remain within the approximately -4.2 V to +4.2 V swing limits.
PCB layout should prioritize short, controlled-impedance traces at the high-impedance OTA input. Keep the signal and ground paths compact, place bypassing capacitors close to the supply pins, and avoid long traces adjacent to switching nodes. These layout practices limit parasitic capacitance, reduce unintended feedback, and preserve the wideband behavior that distinguishes the OPA860 from ordinary low-frequency operational amplifiers.
This page organizes the OPA860ID electrical characteristics, package information, application guidance, and verified alternatives into a design-focused reference. It also compares the available orderable family members so engineers can assess drop-in reuse while accounting for supply configuration, output-current capability, bandwidth, and package differences.
Bộ thay thế dễ dàng lắp đặt cho OPA860ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
OPA860IDR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
OPA860UA
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
OPA860UB
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
OPA860ID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Operational Transconductance Amplifier (OTA) and Buffer |
| Number of Circuits | 1 circuit |
| Channel Count | 1 channel |
| Bandwidth | 370 MHz |
| Điện áp cung cấp | +5 V |
| Output Swing | -4.2 V to +4.2 V |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân OPA860ID 8-pin soic
Cấu hình chân cho OPA860ID (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho OPA860ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
OPA860ID phù hợp cho 6 Áp dụngs: High-Performance Video Signal Conditioning, RF and IF Signal Conditioning, Transconductance-Based Active Filtering, Wideband Instrumentation and Measurement, Current-Drive Signal Generation, Wideband Analog Gain and Buffer Stages.
High-Performance Video Signal Conditioning
The OPA860ID fits video-conditioning stages that require more bandwidth than a conventional precision op amp can provide. Its 370 MHz bandwidth preserves fast transitions and short propagation delay, while the integrated buffer gives the designer a low-impedance voltage output for driving the next stage. The OTA section can also be used where current-mode gain is useful. Operating from a single +5 V supply simplifies the analog rail structure, although the usable output is limited to approximately -4.2 V to +4.2 V. Keep video traces short, use a continuous ground reference, and bypass the supply pins locally so switching activity and parasitic capacitance do not distort the edge response.
Được đề xuất
RF and IF Signal Conditioning
The OPA860ID is suited to RF and IF conditioning blocks because its 370 MHz bandwidth supports high-frequency analog signals while the transconductance output provides a current-output gain mechanism. Designers can evaluate the OTA section as a controlled-current stage or use the internal voltage buffer to present a conventional low-impedance output to subsequent circuitry. Its single +5 V operation is useful in compact RF and IF subsystems, but the approximately -4.2 V to +4.2 V output swing should be checked against downstream bias and clipping requirements. High-speed routing should be impedance controlled, with short feedback loops and careful isolation from switching converters.
Được đề xuất
Transconductance-Based Active Filtering
The OPA860ID can form the central element of active filters that require a controlled current response rather than a conventional voltage gain response. Its transconductance behavior is useful in analog filter experiments and wideband feedback networks where impedance and stability must be evaluated carefully. The 370 MHz bandwidth provides design headroom for filter sections operating well above audio frequencies. Because the OTA is a current-output element, the feedback network determines the effective impedance and loop behavior. Prototype the filter with conservative gain, measure phase margin and settling behavior, and confirm that the approximately -4.2 V to +4.2 V output swing does not clip under worst-case input conditions.
Được đề xuất
Wideband Instrumentation and Measurement
The OPA860ID supports laboratory instrumentation that must combine a current-output stage with a convenient buffered voltage output. Its 370 MHz bandwidth is valuable in impedance analyzers, high-speed probe interfaces, and wideband test fixtures where slow op amps would distort the measured response. The internal buffer allows a straightforward voltage-output configuration, while the OTA section offers current injection for specialized test setups. A single +5 V supply reduces supply complexity in portable instrumentation, but the output headroom and load capability must be verified against the probe or fixture being driven. Use short coax or controlled-impedance PCB routes for test-point connections.
Được đề xuất
Current-Drive Signal Generation
The OPA860ID's operational transconductance section can be used to generate a current proportional to a control voltage, making the device relevant to programmable current sources and wideband analog signal generators. The 370 MHz bandwidth allows the control loop or output waveform to contain significantly more frequency content than audio-band implementations. The voltage buffer provides a convenient way to monitor or distribute the generated signal. Designers should confirm the OTA's output-current range and output-impedance behavior in the manufacturer data sheet before fixing the load range. Keep the high-impedance control node compact and place compensation components where they cannot pick up noise from external cabling.
Được đề xuất
Wideband Analog Gain and Buffer Stages
The OPA860ID is useful when a conventional op amp and a separate wideband buffer would otherwise be required. The integrated voltage buffer supports a direct voltage-output stage, and the OTA section can be arranged as a transconductance element with external feedback. Its 370 MHz bandwidth allows the stage to process fast analog envelopes or video-related waveforms while operating from one +5 V rail. The approximately -4.2 V to +4.2 V output swing is adequate for many low-swing analog systems but leaves less headroom than a dual-rail amplifier. Confirm the load impedance and stability with the complete feedback network rather than relying on nominal bandwidth alone.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho OPA860ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | OPA860IDR | OPA860UA | OPA860UB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Operational Transconductance Amplifier and Buffer | Operational Transconductance Amplifier and Buffer | OPA860 family OTA and Buffer | OPA860 family OTA and Buffer |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Bandwidth | 370 MHz | 370 MHz | 370 MHz | 370 MHz |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V |
| Output Swing | -4.2 V to +4.2 V | -4.2 V to +4.2 V | -4.2 V to +4.2 V | -4.2 V to +4.2 V |
| Output Stage Options | Transconductance output and integrated voltage buffer | Transconductance output and integrated voltage buffer | Transconductance output and integrated voltage buffer | Transconductance output and integrated voltage buffer |
Bảo phân biệt quan trọng
- Integrated OTA and voltage buffer in one device (vsOPA860IDR)
- Wideband transconductance operation (vsOPA860UA)
- Single-supply wideband analog support (vsOPA860UB)
Ghi chú thiết kế
Treat the OTA input as a high-impedance node: keep its copper path short, avoid test pads and long stubs near the pin, and provide a quiet ground reference. Place supply-bypass capacitors immediately across the relevant supply pins and keep switching-regulator connections away from the analog input. Long traces add parasitic capacitance that can move the effective pole and destabilize wideband feedback networks.
Build the complete feedback network before evaluating frequency response, because the OPA860ID's transconductance stage and 370 MHz bandwidth make external impedances part of the circuit definition. Start with conservative loop gain, measure phase margin and settling with light loading, and reduce compensation if the measured response rings. Use short, controlled-impedance routes for any external buffer or test connection.
Do not assume that the approximately -4.2 V to +4.2 V output range is a full dual-rail swing; the OPA860ID operates from a single +5 V supply, leaving reduced headroom at both limits. Check peak signal level, load current, and output-impedance requirements in the manufacturer data sheet before setting gain. Also verify the correct tape-and-reel or tube ordering code for the assembly process before releasing a production order.
Thông tin tuân thủ
Compliance declarations and automotive qualification are not stated in the available product documentation index. Request current manufacturer compliance and qualification records before releasing regulated production hardware.