Texas Instruments

OPA860ID - 370MHz Wide-Bandwidth OTA & Buffer | Texas Instruments

MPN: OPA860ID ✓ 啟用中
+5 V Vdss 8-pin SOIC Package
MOQ: 1 |

OPA860ID 概覽

The Texas Instruments OPA860ID is a single-channel, wide-bandwidth operational transconductance amplifier and voltage buffer packaged in an 8-pin SOIC. It combines a bipolar operational transconductance amplifier (OTA) with a unity-gain buffer output, providing a 370 MHz bandwidth and approximately -4.2 V to +4.2 V output swing on a single +5 V supply.

An operational transconductance amplifier is an amplifier whose output current is controlled by an input voltage. In signal-path terms, an OTA belongs to the operational-amplifier family, but it transfers current rather than presenting a conventional voltage output. The OPA860ID also contains a wide-band voltage buffer that can follow the OTA output, giving designers both transconductance and buffered-voltage operating modes in one package.

The principal feature of the OPA860ID is its 370 MHz small-signal bandwidth. This bandwidth supports high-speed video, RF, and intermediate-frequency signal chains where the transconductance stage must amplify small control or error signals without excessive delay. The OTA can also be used as a current-output stage, while the internal buffer supplies a low-impedance voltage output when the system requires conventional signal routing.

Because the device combines an OTA and a buffer, the circuit designer can select the more appropriate output stage for a given application. The OTA section operates as a voltage-controlled current source, while the buffer section provides a conventional voltage output. This versatility is useful in video and RF systems that evaluate gain, impedance, and loading behavior during prototype development.

Typical uses include high-performance video processing, RF and IF signal conditioning, current-feedback and transconductance-based filter stages, laboratory instrumentation, and wideband analog signal chains. The single +5 V supply arrangement simplifies system design compared with dual-supply analog circuits, although output headroom must remain within the approximately -4.2 V to +4.2 V swing limits.

PCB layout should prioritize short, controlled-impedance traces at the high-impedance OTA input. Keep the signal and ground paths compact, place bypassing capacitors close to the supply pins, and avoid long traces adjacent to switching nodes. These layout practices limit parasitic capacitance, reduce unintended feedback, and preserve the wideband behavior that distinguishes the OPA860 from ordinary low-frequency operational amplifiers.

This page organizes the OPA860ID electrical characteristics, package information, application guidance, and verified alternatives into a design-focused reference. It also compares the available orderable family members so engineers can assess drop-in reuse while accounting for supply configuration, output-current capability, bandwidth, and package differences.

直接替換替代品,適用於 OPA860ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

OPA860IDR

✅ 直接替換
📦 8-pin SOIC
Same 370 MHz bandwidth and electrical function; only the shipment format changes from tube to 8-pin SOIC tape and reel (0% electrical difference)

📋 參考替代品(不在目錄中)

OPA860UA

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin SOIC
Same OPA860 family OTA and buffer function in an 8-pin SOIC footprint; electrical rating differences versus OPA860ID are not quantified in the available documentation

📋 參考替代品(不在目錄中)

OPA860UB

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin SOIC
Same OPA860 family OTA and buffer function in an 8-pin SOIC footprint; temperature or grade differences versus OPA860ID are not quantified in the available documentation

📋 參考替代品(不在目錄中)

OPA860ID 最大額定值與電氣特性

Amplifier Type Operational Transconductance Amplifier (OTA) and Buffer
Number of Circuits 1 circuit
Channel Count 1 channel
Bandwidth 370 MHz
供應電壓 +5 V
Output Swing -4.2 V to +4.2 V
封裝 8-pin SOIC
安裝類型 Surface mount

OPA860ID 8-pin soic 腳位配置指南

OPA860ID(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

OPA860ID 的 8-pin soic 封裝腳位圖

無詳細腳位定義資料: OPA860ID.

請參閱 資料表 以查看完整腳位配置。

典型應用

OPA860ID 適用於 6 應用s: High-Performance Video Signal Conditioning, RF and IF Signal Conditioning, Transconductance-Based Active Filtering, Wideband Instrumentation and Measurement, Current-Drive Signal Generation, Wideband Analog Gain and Buffer Stages.

📺

High-Performance Video Signal Conditioning

The OPA860ID fits video-conditioning stages that require more bandwidth than a conventional precision op amp can provide. Its 370 MHz bandwidth preserves fast transitions and short propagation delay, while the integrated buffer gives the designer a low-impedance voltage output for driving the next stage. The OTA section can also be used where current-mode gain is useful. Operating from a single +5 V supply simplifies the analog rail structure, although the usable output is limited to approximately -4.2 V to +4.2 V. Keep video traces short, use a continuous ground reference, and bypass the supply pins locally so switching activity and parasitic capacitance do not distort the edge response.

🌐

RF and IF Signal Conditioning

The OPA860ID is suited to RF and IF conditioning blocks because its 370 MHz bandwidth supports high-frequency analog signals while the transconductance output provides a current-output gain mechanism. Designers can evaluate the OTA section as a controlled-current stage or use the internal voltage buffer to present a conventional low-impedance output to subsequent circuitry. Its single +5 V operation is useful in compact RF and IF subsystems, but the approximately -4.2 V to +4.2 V output swing should be checked against downstream bias and clipping requirements. High-speed routing should be impedance controlled, with short feedback loops and careful isolation from switching converters.

🔧

Transconductance-Based Active Filtering

The OPA860ID can form the central element of active filters that require a controlled current response rather than a conventional voltage gain response. Its transconductance behavior is useful in analog filter experiments and wideband feedback networks where impedance and stability must be evaluated carefully. The 370 MHz bandwidth provides design headroom for filter sections operating well above audio frequencies. Because the OTA is a current-output element, the feedback network determines the effective impedance and loop behavior. Prototype the filter with conservative gain, measure phase margin and settling behavior, and confirm that the approximately -4.2 V to +4.2 V output swing does not clip under worst-case input conditions.

📟

Wideband Instrumentation and Measurement

The OPA860ID supports laboratory instrumentation that must combine a current-output stage with a convenient buffered voltage output. Its 370 MHz bandwidth is valuable in impedance analyzers, high-speed probe interfaces, and wideband test fixtures where slow op amps would distort the measured response. The internal buffer allows a straightforward voltage-output configuration, while the OTA section offers current injection for specialized test setups. A single +5 V supply reduces supply complexity in portable instrumentation, but the output headroom and load capability must be verified against the probe or fixture being driven. Use short coax or controlled-impedance PCB routes for test-point connections.

🎛️

Current-Drive Signal Generation

The OPA860ID's operational transconductance section can be used to generate a current proportional to a control voltage, making the device relevant to programmable current sources and wideband analog signal generators. The 370 MHz bandwidth allows the control loop or output waveform to contain significantly more frequency content than audio-band implementations. The voltage buffer provides a convenient way to monitor or distribute the generated signal. Designers should confirm the OTA's output-current range and output-impedance behavior in the manufacturer data sheet before fixing the load range. Keep the high-impedance control node compact and place compensation components where they cannot pick up noise from external cabling.

📡

Wideband Analog Gain and Buffer Stages

The OPA860ID is useful when a conventional op amp and a separate wideband buffer would otherwise be required. The integrated voltage buffer supports a direct voltage-output stage, and the OTA section can be arranged as a transconductance element with external feedback. Its 370 MHz bandwidth allows the stage to process fast analog envelopes or video-related waveforms while operating from one +5 V rail. The approximately -4.2 V to +4.2 V output swing is adequate for many low-swing analog systems but leaves less headroom than a dual-rail amplifier. Confirm the load impedance and stability with the complete feedback network rather than relying on nominal bandwidth alone.

推薦產品摘要

OPA860ID Texas Instruments 用於: High-Performance Video Signal Conditioning, RF and IF Signal Conditioning, Transconductance-Based Active Filtering, Wideband Instrumentation and Measurement, Current-Drive Signal Generation, Wideband Analog Gain and Buffer Stages OPA860IDR Tape-and-reel assembly option for the same OPA860 function 用於: High-Performance Video Signal Conditioning, RF and IF Signal Conditioning, Wideband Instrumentation and Measurement OPA860UA OPA860 family variant for laboratory evaluation 用於: Transconductance-Based Active Filtering, Wideband Analog Gain and Buffer Stages OPA860UB OPA860 family option for waveform-generation evaluation 用於: Current-Drive Signal Generation
What is the OPA860ID?
The OPA860ID is a wide-bandwidth operational transconductance amplifier and voltage buffer from Texas Instruments. It combines a bipolar OTA, which converts an input-voltage error into an output current, with a unity-gain voltage buffer in one 8-pin SOIC package. According to the Texas Instruments product page, the device is intended for high-performance video, RF, and IF circuitry and supports a 370 MHz bandwidth.
What are the key specifications of OPA860ID?
The OPA860ID is a single-channel device with a 370 MHz bandwidth, approximately -4.2 V to +4.2 V output swing, and an 8-pin SOIC package. It operates from a single +5 V supply and contains both an operational transconductance amplifier and a voltage buffer. The Texas Instruments OPA860 product page identifies wide-bandwidth video, RF, and IF systems as the principal application areas.
Where can I download the OPA860ID datasheet PDF?
The official OPA860ID datasheet and supporting documents are available from the Texas Instruments OPA860 product page at https://www.ti.com/product/OPA860. Select the Data sheet link in the technical documentation area for the wide-bandwidth OTA and buffer. The manufacturer page also provides ordering information, quality data, and application support for the OPA860 family.
Where can I find the OPA860ID pinout?
Use the pin-description table and package drawing in the Texas Instruments OPA860 datasheet to assign the eight SOIC pins. The device combines the OTA and buffer in one package, so the pin functions should be taken directly from the manufacturer documentation rather than inferred from a generic operational-amplifier diagram. The product family is offered in an 8-pin SOIC configuration.
Can the OPA860ID be used as a conventional voltage buffer?
Yes, the OPA860ID includes a voltage buffer in addition to its OTA section. Texas Instruments describes the component as a wide-bandwidth operational transconductance amplifier and buffer, giving it two useful output paths. The OTA section behaves as a voltage-controlled current source, while the buffer section provides a conventional low-impedance voltage output for high-speed signal routing.
What is the OPA860ID bandwidth?
The OPA860ID has a bandwidth of 370 MHz. According to the Texas Instruments OPA860 product description, the wide-bandwidth bipolar OTA and buffer are intended for video, RF, and IF systems. That bandwidth is the principal reason to choose this device over a general-purpose operational amplifier when signal propagation delay and high-frequency response are critical.
How much output voltage swing does the OPA860ID provide?
The OPA860ID provides approximately -4.2 V to +4.2 V output swing from a single +5 V supply. This leaves headroom for the internal amplifier stages and keeps the output inside the device's usable linear region. Applications that require a larger swing should use a higher supply arrangement or a different amplifier family.
Is OPA860ID suitable for RF and IF signal chains?
Yes, the OPA860ID is specifically suited to RF and IF circuitry because it combines a 370 MHz bandwidth with selectable transconductance and buffered-voltage outputs. Texas Instruments lists RF and IF systems among its intended applications. The wideband OTA can serve as a current-output gain stage, while the buffer can provide a low-impedance drive for downstream circuitry.
What is the difference between OPA860ID and OPA860IDR?
OPA860ID and OPA860IDR identify orderable versions of the same OPA860 family device, and both are listed in 8-pin SOIC form. OPA860ID is the tube-packed designation, while OPA860IDR is the tape-and-reel designation used for automated volume handling. Their electrical functionality remains the same, so the packaging code must match the board's assembly process.
What can replace the OPA860ID?
No independent drop-in replacement is established for the OPA860ID from the available component cross-reference information. The closest orderable family member is OPA860IDR, which retains the OPA860 electrical design and 8-pin SOIC footprint but changes only the shipping format to tape and reel. Treat any other OTA as a redesign candidate unless its pinout, supply range, transconductance, bandwidth, and stability are independently verified.
Is OPA860ID the same as a conventional operational amplifier?
No. The OPA860ID combines a conventional voltage buffer with an operational transconductance amplifier whose output is current-driven. A standard operational amplifier develops an output voltage from its differential input, whereas the OTA transfers current according to a transconductance factor. The on-chip buffer lets the same package provide a conventional voltage output when required.
When should I choose the OPA860ID over a general-purpose op amp?
Choose the OPA860ID when the design needs both transconductance operation and a wideband buffered-voltage output, particularly in video, RF, or IF signal paths. Its 370 MHz bandwidth and single +5 V supply make it suitable for high-speed analog stages. A general-purpose operational amplifier is more appropriate when only conventional voltage gain, low cost, or low power is required.
OPA860ID vs OPA860IDR: which version fits my assembly process?
Select OPA860ID for tube-based or manual low-volume handling and OPA860IDR for tape-and-reel assembly. Both belong to the same wide-bandwidth OTA and buffer family, and the cross-reference listing confirms the OPA860IDR package designation. The choice should follow the PCB assembly method and order quantity rather than a change in circuit functionality.
How should I lay out a PCB for the OPA860ID?
Keep the high-impedance OTA input traces short, place supply-bypass capacitors close to the device pins, and route high-speed signals over continuous ground planes. Avoid placing sensitive input traces beside switching nodes or long digital traces. Texas Instruments identifies the OPA860 as a wideband bipolar device, so short feedback paths and minimized parasitic capacitance are essential for predictable high-frequency behavior.
Where can I buy OPA860ID online?
The OPA860ID can be requested through the Request a Quote form on this page. The form is the appropriate route for current availability, order quantity, lead time, and shipment configuration without relying on a static price table. The manufacturer lists the OPA860 family for ordering, and the device is also cataloged in the 8-pin SOIC configuration.
What is the price and lead time of OPA860ID?
Current OPA860ID pricing and lead time should be confirmed through the Request a Quote form on this page. The form captures the required quantity, package, and shipment details so the order can be quoted for the current supply position. Static price figures are not used here because they can change independently of the live quotation.
Is OPA860ID RoHS compliant and available for automotive use?
The OPA860ID is a general-purpose wide-bandwidth analog IC, and its RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the available product documentation index. Automotive qualification is also not established by the orderable information. Request the current compliance and qualification documents before releasing a regulated or automotive production design.

工程參考資料,適用於 OPA860ID — 比較、設計指引及合規資訊。

選型指南

Choose OPA860ID when the signal path needs a wide-bandwidth operational transconductance stage, a conventional buffered-voltage output, or both functions in the same package. Its 370 MHz bandwidth and single +5 V operation are particularly appropriate for video, RF, IF, instrumentation, and active-filter prototypes. Select OPA860IDR when the board assembly process requires tape-and-reel handling; its electrical function and 8-pin SOIC footprint remain the same. OPA860UA and OPA860UB are useful family-level options when a specific orderable temperature or grade configuration is required, but their electrical differences should be checked against the manufacturer data sheet before substitution. Do not use a generic OTA or conventional operational amplifier as a drop-in replacement unless pinout, transconductance, bandwidth, supply range, output-current capability, and stability have all been verified.

與替代品比較

參數 本產品 OPA860IDR OPA860UA OPA860UB
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Type Operational Transconductance Amplifier and Buffer Operational Transconductance Amplifier and Buffer OPA860 family OTA and Buffer OPA860 family OTA and Buffer
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit
Bandwidth 370 MHz 370 MHz 370 MHz 370 MHz
Supply Voltage +5 V +5 V +5 V +5 V
Output Swing -4.2 V to +4.2 V -4.2 V to +4.2 V -4.2 V to +4.2 V -4.2 V to +4.2 V
Output Stage Options Transconductance output and integrated voltage buffer Transconductance output and integrated voltage buffer Transconductance output and integrated voltage buffer Transconductance output and integrated voltage buffer

主要差異化特點

  • Integrated OTA and voltage buffer in one device (對比OPA860IDR)
  • Wideband transconductance operation (對比OPA860UA)
  • Single-supply wideband analog support (對比OPA860UB)

設計說明

Treat the OTA input as a high-impedance node: keep its copper path short, avoid test pads and long stubs near the pin, and provide a quiet ground reference. Place supply-bypass capacitors immediately across the relevant supply pins and keep switching-regulator connections away from the analog input. Long traces add parasitic capacitance that can move the effective pole and destabilize wideband feedback networks.

Build the complete feedback network before evaluating frequency response, because the OPA860ID's transconductance stage and 370 MHz bandwidth make external impedances part of the circuit definition. Start with conservative loop gain, measure phase margin and settling with light loading, and reduce compensation if the measured response rings. Use short, controlled-impedance routes for any external buffer or test connection.

Do not assume that the approximately -4.2 V to +4.2 V output range is a full dual-rail swing; the OPA860ID operates from a single +5 V supply, leaving reduced headroom at both limits. Check peak signal level, load current, and output-impedance requirements in the manufacturer data sheet before setting gain. Also verify the correct tape-and-reel or tube ordering code for the assembly process before releasing a production order.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

Compliance declarations and automotive qualification are not stated in the available product documentation index. Request current manufacturer compliance and qualification records before releasing regulated production hardware.

資料驗證日期: 2026-11-09 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

OPA860ID datasheet OPA860ID datasheet pdf OPA860ID pinout OPA860ID 370MHz OPA860ID transconductance amplifier OPA860ID SOIC-8 OPA860ID application circuit OPA860ID vs OPA860IDR OPA860ID replacement OPA860ID cross reference OPA860ID price OPA860ID stock Texas Instruments OPA860ID OPA860ID video amplifier OPA860ID RF IF circuitry

相關元件與詞彙

Texas Instruments OPA860ID OPA860IDR OPA860UA OPA860UB Operational Transconductance Amplifier OTA Operational Amplifier Voltage Buffer Bipolar Amplifier Voltage-Controlled Current Source Single +5 V Supply 370 MHz Bandwidth Transconductance Gain Current Feedback 8-pin SOIC SOIC Package Family Surface Mount High-Speed Video RF Signal Conditioning IF Signal Chain Active Filter Wideband Instrumentation Output Swing Texas Instruments Product Documentation
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情