P1010NXN5DFA - QorIQ P1 SoC, 533 MHz, 425-TEPBGA | NXP
MPN: P1010NXN5DFA ✓ Hoạt độngP1010NXN5DFA Tóm tắt
A SoC (System-on-Chip) of this class combines an application-class CPU, memory controllers and high-speed serial interfaces on a single die. The QorIQ P1 family sits below NXP's high-end Layerscape and PowerQUICC lines in cost and power, targeting cost- and power-sensitive networking and industrial control designs where a full multicore CPU would be overkill. The P1010NXN5DFA specifically enables embedded OEMs to integrate networking, storage and security into a single BGA footprint rather than a discrete MPU plus companion logic.
Key features include a single Power Architecture e500v2 core at up to 1.0 GHz, three GbE interfaces supporting SGMII/RGMII, two PCIe Gen 2 controllers, two USB 2.0 controllers (host and device), two SATA 2.0 interfaces, a 32-bit DDR3/DDR3L memory controller with ECC, an integrated SEC security engine and a hardware Trusted Boot flow. The industrial temperature grade (-40C to +105C) makes the part suitable for outdoor or ruggedized enclosures.
Typical applications include industrial IoT gateways, factory automation controllers, secure routers, building automation controllers and energy/smart-grid edge nodes. The integrated SEC engine and Trusted Boot flow reduce BOM cost for designs that must meet common security certifications. Customers choosing this part typically want a single BGA SoC that drops onto a 4-layer PCB with DDR3 DRAM and a power management IC, replacing legacy designs that previously required an MPU plus external GbE switch plus crypto coprocessor.
When designing in the P1010NXN5DFA, plan for thermal dissipation across the 425-ball BGA, use 1.5 V/1.0 V/3.3 V rail sequencing for proper core and I/O power-up, and follow the NXP reference design for DDR3 fly-by topology and SERDES routing. Firmware and U-Boot ports are maintained by the NXP QorIQ SDK and the open-source community.
This page synthesizes distributor pricing, datasheet specifications, and drop-in same-family alternatives not found in the manufacturer datasheet alone, giving engineers a single place to evaluate the P1010NXN5DFA against direct siblings such as P1010NSN5DFA, P1010NXN5KHB and P1010NXN5HHB.
Bộ thay thế dễ dàng lắp đặt cho P1010NXN5DFA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với P1010NXN5DFA (cùng hình factor và footprint) — khác nhau ở Core Architecture, Package, RoHS Status, Security Engine, Mounting Type.
P1010NSN5DFA
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
P1010NXN5KHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1010NXN5HHB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
P1010NSE5DFA
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
P1014NXN5DFA
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →P1010NXN5DFA Tỷ lệ tối đa & tính chất điện
| Core Architecture | PowerPC e500v2 (QorIQ P1) |
| Core Count | 1 |
| Maximum Core Frequency | 1.0 GHz |
| Base Core Frequency | 533 MHz (also qualified at 667 MHz per industry listing) |
| Khoảng nhiệt độ hoạt động | -40C to +105C (industrial) |
| Hộp | 425-TEPBGA I (19x19) |
| Process Technology | CMOS |
| Ethernet Interfaces | 3x GbE (SGMII/RGMII) |
| PCIe Controllers | 2x PCIe Gen 2 |
| USB Controllers | 2x USB 2.0 (host + device) |
| SATA Interfaces | 2x SATA 2.0 |
| DDR Memory Controller | 32-bit DDR3/DDR3L with ECC |
| Security Engine | SEC (Integrated, with Trusted Boot) |
| Kiểu lắp đặt | Surface Mount (BGA, 425 balls) |
| Trạng thái RoHS | Compliant (terminal finish: Tin-Silver, JESD-609 e2) |
| Terminal Form | Ball |
| No. of Terminals | 425 |
| Temperature Grade | Industrial |
Hướng dẫn cấu hình chân P1010NXN5DFA 425-tepbga i (19x19)
Cấu hình chân cho P1010NXN5DFA (425-tepbga i (19x19) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho P1010NXN5DFA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
P1010NXN5DFA phù hợp cho 6 Áp dụngs: Industrial IoT Gateway, Secure Industrial Router, Factory Automation Controller, Smart Grid Edge Node, Building Automation Controller, Networked Medical Device Controller.
Industrial IoT Gateway
The P1010NXN5DFA is a strong fit for industrial IoT gateways because it integrates three GbE ports, two PCIe lanes, two USB 2.0 controllers, two SATA ports, and a hardware SEC crypto engine into a single 425-ball BGA SoC. The 1.0 GHz e500v2 core and 32-bit DDR3/DDR3L with ECC provide enough headroom for protocol translation, TLS termination, and edge analytics. The industrial -40C to +105C temperature rating supports deployment in factory floors and outdoor enclosures where consumer SoCs would fail thermal stress testing. A typical design uses one GbE port as WAN uplink and two as LAN switch interfaces, with a PCIe Wi-Fi or LTE modem on the second PCIe lane.
Được đề xuất
Secure Industrial Router
The P1010NXN5DFA suits secure industrial router designs because its three integrated GbE interfaces (SGMII/RGMII) can serve WAN, LAN and DMZ ports without an external switch, while the SEC crypto engine accelerates IPSec and TLS handshakes at line rate. The integrated Trusted Boot flow verifies firmware signatures at power-on, critical for routers exposed to physical tampering. Operating from -40C to +105C, it survives outdoor cabinet installations. Unlike pure-play networking ASSPs, the e500v2 core runs Linux or VxWorks, enabling SD-WAN stacks and zero-touch provisioning firmware at the edge.
Được đề xuất
Factory Automation Controller
The P1010NXN5DFA is well matched to factory automation controllers requiring deterministic Ethernet and PCIe I/O expansion. Its 1.0 GHz PowerPC core can host real-time OS tasks like EtherCAT or PROFINET master firmware, while the two PCIe Gen 2 lanes accept fieldbus cards or vision capture cards. The industrial -40C to +105C temperature grade handles motor cabinet heat-rise. Unlike microcontrollers, the QorIQ P1 SoC integrates network security and Trusted Boot in one BGA, reducing BOM and PCB area for cost-sensitive PLC and HMI designs. Memory bandwidth from DDR3 with ECC supports deterministic communication cycles.
Được đề xuất
Smart Grid Edge Node
The P1010NXN5DFA is suitable for smart-grid edge nodes because of its industrial -40C to +105C temperature rating, hardware SEC acceleration for IEEE 1815 (DNP3) and IEC 61850 cryptographic profiles, and Trusted Boot flow required for utility certification. The three GbE interfaces support substation LAN, WAN uplink and protective relay I/O, while the two SATA ports enable local event logging. The integrated security engine reduces BOM cost versus designs that previously required a discrete MPU plus external crypto coprocessor. Power sequencing across 1.0 V/1.5 V/3.3 V rails is documented in NXP reference designs.
Được đề xuất
Building Automation Controller
The P1010NXN5DFA fits building automation controller designs that must aggregate BACnet, Modbus, and KNX traffic while running local control logic. Its three GbE ports serve IT and OT network segments without an external switch, and the USB 2.0 controllers accept touchscreens or Zigbee/Z-Wave dongles. The 1.0 GHz e500v2 core comfortably handles building management firmware, BACnet/IP stack and local visualization tasks in parallel. Industrial temperature rating supports rooftop and mechanical-room deployments where ambient temperatures routinely exceed commercial-grade SoC limits. Trusted Boot secures firmware against unauthorized updates.
Được đề xuất
Networked Medical Device Controller
The P1010NXN5DFA suits networked medical device controllers that need deterministic Ethernet for DICOM transfer and hardware encryption for HIPAA compliance. The SEC engine accelerates TLS sessions for medical imaging data, and Trusted Boot protects patient-data integrity at power-on. The 1.0 GHz core, 32-bit DDR3 controller with ECC, and 425-ball BGA fit into compact enclosure designs. Industrial temperature rating supports autoclave-adjacent and equipment-room installations. The integrated PCIe lanes accept medical imaging capture cards or wireless modules without a companion chipset.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho P1010NXN5DFA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | P1010NSN5DFA | P1010NXN5KHB | P1010NXN5HHB | P1010NSE5DFA | P1014NXN5DFA |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) |
| Core Architecture | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) |
| GbE Interfaces | 3x | 3x | 3x | 3x | 3x | 3x |
| PCIe Controllers | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 |
Bảo phân biệt quan trọng
- Higher core clock than same-family S-bin alternative (vsP1010NSN5DFA)
- Industrial temperature grade for harsh environments (vsCommercial-grade NXP QorIQ P1 alternatives)
- Integrated SEC engine and Trusted Boot (vsDiscrete MPU plus external crypto coprocessor designs)
Ghi chú thiết kế
The P1010NXN5DFA is delivered in a 425-ball 19x19 mm TEPBGA requiring 4-layer or 6-layer PCB stack-up with microvia or laser-drilled vias. Per NXP QorIQ P1 hardware design guides, place DDR3 DRAM on the top side immediately adjacent to the SoC's DRAM controller pins in fly-by topology, and isolate SERDES lanes (SGMII, PCIe, SATA) from noisy power rails with a continuous ground reference plane under the BGA. Use impedance-controlled traces (100 ohm diff for SERDES) and follow the NXP P1010 reference design for length-matching.
The P1010NXN5DFA requires sequenced power rails: 1.0 V core, 1.5 V DDR3, and 3.3 V I/O. The NXP P1010 datasheet specifies a strict power-up sequence to avoid latch-up; designers should use a multi-rail PMIC (e.g., NXP PF-series or equivalent) with programmable delay or tracking to meet this requirement. Decoupling capacitors must be placed as close as possible to the BGA balls, with a mix of 0.1 uF and 10 uF ceramic capacitors to suppress both high-frequency and bulk current transients.
At 1.0 GHz continuous operation the P1010NXN5DFA dissipates several watts through the BGA. With a typical theta-JA around 15 C/W for a 4-layer JEDEC test board, junction temperature rises ~15 C per watt above ambient. For industrial -40C to +105C operation, designers must provide adequate copper thermal relief under the BGA and may need a thermal pad or heatsink in enclosed designs. Verify junction temperature against the NXP P1010 thermal model before finalizing the enclosure.
Common pitfalls when bringing up the P1010NXN5DFA include: (1) forgetting to load the DDR3 SPD parameters into the hardware initialization code, causing intermittent memory failures; (2) failing to configure SERDES reference clocks correctly, leading to SGMII/PCIe/SATA link training failures; (3) mixing up the e500v2 reset polarity and holding the SoC in reset indefinitely; (4) omitting the eFuse or IFC NOR flash that stores the Trusted Boot signatures. Always start with the NXP QorIQ SDK and a known-good U-Boot port to validate the hardware before porting production firmware.
Thông tin tuân thủ
JESD-609 e2 (Tin-Silver) terminal finish confirms lead-free RoHS compliance per industry listings. AEC-Q100 is not applicable - this is an industrial networking SoC, not an automotive grade part.
