P1010NXN5DFA - QorIQ P1 SoC, 533 MHz, 425-TEPBGA | NXP
부품 번호: P1010NXN5DFA ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $34.94 | $34.94 |
| 10 | $32.1 | $321.00 |
| 100 | $28.75 | $2,875.00 |
| 500 | $25.2 | $12,600.00 |
| 1,000 | $22.5 | $22,500.00 |
P1010NXN5DFA 개요
A SoC (System-on-Chip) of this class combines an application-class CPU, memory controllers and high-speed serial interfaces on a single die. The QorIQ P1 family sits below NXP's high-end Layerscape and PowerQUICC lines in cost and power, targeting cost- and power-sensitive networking and industrial control designs where a full multicore CPU would be overkill. The P1010NXN5DFA specifically enables embedded OEMs to integrate networking, storage and security into a single BGA footprint rather than a discrete MPU plus companion logic.
Key features include a single Power Architecture e500v2 core at up to 1.0 GHz, three GbE interfaces supporting SGMII/RGMII, two PCIe Gen 2 controllers, two USB 2.0 controllers (host and device), two SATA 2.0 interfaces, a 32-bit DDR3/DDR3L memory controller with ECC, an integrated SEC security engine and a hardware Trusted Boot flow. The industrial temperature grade (-40C to +105C) makes the part suitable for outdoor or ruggedized enclosures.
Typical applications include industrial IoT gateways, factory automation controllers, secure routers, building automation controllers and energy/smart-grid edge nodes. The integrated SEC engine and Trusted Boot flow reduce BOM cost for designs that must meet common security certifications. Customers choosing this part typically want a single BGA SoC that drops onto a 4-layer PCB with DDR3 DRAM and a power management IC, replacing legacy designs that previously required an MPU plus external GbE switch plus crypto coprocessor.
When designing in the P1010NXN5DFA, plan for thermal dissipation across the 425-ball BGA, use 1.5 V/1.0 V/3.3 V rail sequencing for proper core and I/O power-up, and follow the NXP reference design for DDR3 fly-by topology and SERDES routing. Firmware and U-Boot ports are maintained by the NXP QorIQ SDK and the open-source community.
This page synthesizes distributor pricing, datasheet specifications, and drop-in same-family alternatives not found in the manufacturer datasheet alone, giving engineers a single place to evaluate the P1010NXN5DFA against direct siblings such as P1010NSN5DFA, P1010NXN5KHB and P1010NXN5HHB.
드롭인 대체품: P1010NXN5DFA — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: P1010NXN5DFA (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Package, RoHS Status, Security Engine, Mounting Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
P1010NSN5DFA
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
P1010NXN5KHB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
P1010NXN5HHB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
P1010NSE5DFA
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
P1014NXN5DFA
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$22.1 / 개
데이터시트 보기 →P1010NXN5DFA 최대 정격 & 전기적 특성
| Core Architecture | PowerPC e500v2 (QorIQ P1) |
| Core Count | 1 |
| Maximum Core Frequency | 1.0 GHz |
| Base Core Frequency | 533 MHz (also qualified at 667 MHz per industry listing) |
| 동작 온도 범위 | -40C to +105C (industrial) |
| 패키지 | 425-TEPBGA I (19x19) |
| Process Technology | CMOS |
| Ethernet Interfaces | 3x GbE (SGMII/RGMII) |
| PCIe Controllers | 2x PCIe Gen 2 |
| USB Controllers | 2x USB 2.0 (host + device) |
| SATA Interfaces | 2x SATA 2.0 |
| DDR Memory Controller | 32-bit DDR3/DDR3L with ECC |
| Security Engine | SEC (Integrated, with Trusted Boot) |
| 실장 유형 | Surface Mount (BGA, 425 balls) |
| RoHS 상태 | Compliant (terminal finish: Tin-Silver, JESD-609 e2) |
| Terminal Form | Ball |
| No. of Terminals | 425 |
| Temperature Grade | Industrial |
P1010NXN5DFA 425-tepbga i (19x19) 핀 구성 가이드
P1010NXN5DFA(425-tepbga i (19x19) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: P1010NXN5DFA.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
P1010NXN5DFA 적합 용도: 6 애플리케이션s: Industrial IoT Gateway, Secure Industrial Router, Factory Automation Controller, Smart Grid Edge Node, Building Automation Controller, Networked Medical Device Controller.
Industrial IoT Gateway
The P1010NXN5DFA is a strong fit for industrial IoT gateways because it integrates three GbE ports, two PCIe lanes, two USB 2.0 controllers, two SATA ports, and a hardware SEC crypto engine into a single 425-ball BGA SoC. The 1.0 GHz e500v2 core and 32-bit DDR3/DDR3L with ECC provide enough headroom for protocol translation, TLS termination, and edge analytics. The industrial -40C to +105C temperature rating supports deployment in factory floors and outdoor enclosures where consumer SoCs would fail thermal stress testing. A typical design uses one GbE port as WAN uplink and two as LAN switch interfaces, with a PCIe Wi-Fi or LTE modem on the second PCIe lane.
추천
Secure Industrial Router
The P1010NXN5DFA suits secure industrial router designs because its three integrated GbE interfaces (SGMII/RGMII) can serve WAN, LAN and DMZ ports without an external switch, while the SEC crypto engine accelerates IPSec and TLS handshakes at line rate. The integrated Trusted Boot flow verifies firmware signatures at power-on, critical for routers exposed to physical tampering. Operating from -40C to +105C, it survives outdoor cabinet installations. Unlike pure-play networking ASSPs, the e500v2 core runs Linux or VxWorks, enabling SD-WAN stacks and zero-touch provisioning firmware at the edge.
추천
Factory Automation Controller
The P1010NXN5DFA is well matched to factory automation controllers requiring deterministic Ethernet and PCIe I/O expansion. Its 1.0 GHz PowerPC core can host real-time OS tasks like EtherCAT or PROFINET master firmware, while the two PCIe Gen 2 lanes accept fieldbus cards or vision capture cards. The industrial -40C to +105C temperature grade handles motor cabinet heat-rise. Unlike microcontrollers, the QorIQ P1 SoC integrates network security and Trusted Boot in one BGA, reducing BOM and PCB area for cost-sensitive PLC and HMI designs. Memory bandwidth from DDR3 with ECC supports deterministic communication cycles.
추천
Smart Grid Edge Node
The P1010NXN5DFA is suitable for smart-grid edge nodes because of its industrial -40C to +105C temperature rating, hardware SEC acceleration for IEEE 1815 (DNP3) and IEC 61850 cryptographic profiles, and Trusted Boot flow required for utility certification. The three GbE interfaces support substation LAN, WAN uplink and protective relay I/O, while the two SATA ports enable local event logging. The integrated security engine reduces BOM cost versus designs that previously required a discrete MPU plus external crypto coprocessor. Power sequencing across 1.0 V/1.5 V/3.3 V rails is documented in NXP reference designs.
추천
Building Automation Controller
The P1010NXN5DFA fits building automation controller designs that must aggregate BACnet, Modbus, and KNX traffic while running local control logic. Its three GbE ports serve IT and OT network segments without an external switch, and the USB 2.0 controllers accept touchscreens or Zigbee/Z-Wave dongles. The 1.0 GHz e500v2 core comfortably handles building management firmware, BACnet/IP stack and local visualization tasks in parallel. Industrial temperature rating supports rooftop and mechanical-room deployments where ambient temperatures routinely exceed commercial-grade SoC limits. Trusted Boot secures firmware against unauthorized updates.
추천
Networked Medical Device Controller
The P1010NXN5DFA suits networked medical device controllers that need deterministic Ethernet for DICOM transfer and hardware encryption for HIPAA compliance. The SEC engine accelerates TLS sessions for medical imaging data, and Trusted Boot protects patient-data integrity at power-on. The 1.0 GHz core, 32-bit DDR3 controller with ECC, and 425-ball BGA fit into compact enclosure designs. Industrial temperature rating supports autoclave-adjacent and equipment-room installations. The integrated PCIe lanes accept medical imaging capture cards or wireless modules without a companion chipset.
추천
추천 제품 요약
엔지니어링 참조 데이터: P1010NXN5DFA — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | P1010NSN5DFA | P1010NXN5KHB | P1010NXN5HHB | P1010NSE5DFA | P1014NXN5DFA |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) | 425-TEPBGA I (19x19) |
| Core Architecture | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) | PowerPC e500v2 (QorIQ P1) |
| GbE Interfaces | 3x | 3x | 3x | 3x | 3x | 3x |
| PCIe Controllers | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 | 2x PCIe Gen 2 |
주요 차별점
- Higher core clock than same-family S-bin alternative (vs P1010NSN5DFA)
- Industrial temperature grade for harsh environments (vs Commercial-grade NXP QorIQ P1 alternatives)
- Integrated SEC engine and Trusted Boot (vs Discrete MPU plus external crypto coprocessor designs)
설계 노트
The P1010NXN5DFA is delivered in a 425-ball 19x19 mm TEPBGA requiring 4-layer or 6-layer PCB stack-up with microvia or laser-drilled vias. Per NXP QorIQ P1 hardware design guides, place DDR3 DRAM on the top side immediately adjacent to the SoC's DRAM controller pins in fly-by topology, and isolate SERDES lanes (SGMII, PCIe, SATA) from noisy power rails with a continuous ground reference plane under the BGA. Use impedance-controlled traces (100 ohm diff for SERDES) and follow the NXP P1010 reference design for length-matching.
The P1010NXN5DFA requires sequenced power rails: 1.0 V core, 1.5 V DDR3, and 3.3 V I/O. The NXP P1010 datasheet specifies a strict power-up sequence to avoid latch-up; designers should use a multi-rail PMIC (e.g., NXP PF-series or equivalent) with programmable delay or tracking to meet this requirement. Decoupling capacitors must be placed as close as possible to the BGA balls, with a mix of 0.1 uF and 10 uF ceramic capacitors to suppress both high-frequency and bulk current transients.
At 1.0 GHz continuous operation the P1010NXN5DFA dissipates several watts through the BGA. With a typical theta-JA around 15 C/W for a 4-layer JEDEC test board, junction temperature rises ~15 C per watt above ambient. For industrial -40C to +105C operation, designers must provide adequate copper thermal relief under the BGA and may need a thermal pad or heatsink in enclosed designs. Verify junction temperature against the NXP P1010 thermal model before finalizing the enclosure.
Common pitfalls when bringing up the P1010NXN5DFA include: (1) forgetting to load the DDR3 SPD parameters into the hardware initialization code, causing intermittent memory failures; (2) failing to configure SERDES reference clocks correctly, leading to SGMII/PCIe/SATA link training failures; (3) mixing up the e500v2 reset polarity and holding the SoC in reset indefinitely; (4) omitting the eFuse or IFC NOR flash that stores the Trusted Boot signatures. Always start with the NXP QorIQ SDK and a known-good U-Boot port to validate the hardware before porting production firmware.
규정 준수 정보
JESD-609 e2 (Tin-Silver) terminal finish confirms lead-free RoHS compliance per industry listings. AEC-Q100 is not applicable - this is an industrial networking SoC, not an automotive grade part.
